Related references
Note: Only part of the references are listed.Adhesive bond strength of PEO coated AA6060-T6
Dominic Shore et al.
SURFACE & COATINGS TECHNOLOGY (2021)
Current status of carbon fibre and carbon fibre composites recycling
Jin Zhang et al.
COMPOSITES PART B-ENGINEERING (2020)
Introduction to Plasma Electrolytic Oxidation-An Overview of the Process and Applications
Frank Simchen et al.
COATINGS (2020)
Relaxation Kinetics of Plasma Electrolytic Oxidation Coated Al Electrode: Insight into the Role of Negative Current
Aleksey B. Rogov et al.
JOURNAL OF PHYSICAL CHEMISTRY C (2020)
Role of cathodic current in plasma electrolytic oxidation of Al: A quantitative approach to in-situ evaluation of cathodically induced effects
Aleksey B. Rogov et al.
ELECTROCHIMICA ACTA (2019)
In-situ SEM analysis of brittle plasma electrolytic oxidation coating bonded to plastic aluminum substrate: Microstructure and fracture behaviors
Yongchun Zou et al.
MATERIALS CHARACTERIZATION (2019)
Reactive Synthesis of Ceramic-Metal Composites
Nahum Travitzky et al.
ADVANCED ENGINEERING MATERIALS (2018)
Review of the Soft Sparking Issues in Plasma Electrolytic Oxidation
Dah-Shyang Tsai et al.
METALS (2018)
The Role of Cathodic Current in Plasma Electrolytic Oxidation of Aluminum: Phenomenological Concepts of the Soft Sparking Mode
Aleksey B. Rogov et al.
LANGMUIR (2017)
Joining of carbon fibre reinforced polymer (CFRP) composites and aluminium alloys - A review
A. Pramanik et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2017)
Delay in micro-discharges appearance during PEO of Al: Evidence of a mechanism of charge accumulation at the electrolyte/oxide interface
J. Martin et al.
APPLIED SURFACE SCIENCE (2017)
The role of cathodic current in PEO of aluminum: Influence of cationic electrolyte composition on the transient current-voltage curves and the discharges optical emission spectra
A. B. Rogov et al.
APPLIED SURFACE SCIENCE (2017)
Nano-structured interpenetrating composites with enhanced Young's modulus and desired Poisson's ratio
Hanxing Zhu et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2016)
Influence of coating morphology on adhesive bonding of titanium pre-treated by plasma electrolytic oxidation
S. Aliasghari et al.
SURFACE & COATINGS TECHNOLOGY (2016)
Cyclic compression behavior and energy dissipation of aluminum foam-polyurethane interpenetrating phase composites
Shaobo Liu et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2015)
High growth rate, wear resistant coatings on an Al-Cu-Li alloy by plasma electrolytic oxidation in concentrated aluminate electrolytes
Ying-liang Cheng et al.
SURFACE & COATINGS TECHNOLOGY (2015)
Suggested mechanism for the MAO ceramic coating on aluminium substrates using bipolar current mode in the alkaline silicate electrolytes
Mohannad M. S. Al Bosta et al.
APPLIED SURFACE SCIENCE (2014)
Enhancement in specific strength of open cell aluminium foams through plasma electrolytic oxidation treatment
T. Abdulla et al.
SCRIPTA MATERIALIA (2014)
INFLUENCE OF THE CATHODIC PULSE ON THE FORMATION AND MORPHOLOGY OF OXIDE COATINGS ON ALUMINIUM PRODUCED BY PLASMA ELECTROLYTIC OXIDATION
W. Gebarowski et al.
ARCHIVES OF METALLURGY AND MATERIALS (2013)
Effects of electrical parameters on plasma electrolytic oxidation of aluminium
J. Martin et al.
SURFACE & COATINGS TECHNOLOGY (2013)
Processing of ceramic-metal composites
N. Travitzky
ADVANCES IN APPLIED CERAMICS (2012)
The influence of pulse timing and current mode on the microstructure and corrosion behaviour of a plasma electrolytic oxidation (PEO) coated AM60B magnesium alloy
R. O. Hussein et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2012)
Microstructure and multi-scale mechanical behavior of hard anodized and plasma electrolytic oxidation (PEO) coatings on aluminum alloy 5052
J. M. Wheeler et al.
SURFACE & COATINGS TECHNOLOGY (2012)
Mechanisms of interfacial adhesion in metal-polymer composites - Effect of chemical treatment
Carol Ochoa-Putman et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2011)
Effect of Plasma Electrolytic Oxidation coating on the specific strength of open-cell aluminium foams
T. Abdulla et al.
MATERIALS & DESIGN (2011)
An investigation into the mechanical and tribological properties of plasma electrolytic oxidation and hard-anodized coatings on 6082 aluminum alloy
Ugur Malayoglu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Changes induced by process parameters in oxide layers grown by the PEO process on Al alloys
A. Melhem et al.
SURFACE & COATINGS TECHNOLOGY (2011)
The influences of duty cycle on the bonding strength of AZ31B magnesium alloy by microarc oxidation treatment
Yuming Tang et al.
SURFACE & COATINGS TECHNOLOGY (2010)
Plasma electrolytic oxidation of pre-anodized aluminium
E. Matykina et al.
CORROSION SCIENCE (2009)
Use of LCA to evaluate the environmental benefits of substituting chromic acid anodizing (CAA)
Erwan Harscoet et al.
JOURNAL OF CLEANER PRODUCTION (2008)
Tailored aluminium oxide layers by bipolar current adjustment in the Plasma Electrolytic Oxidation (PEO) process
F. Jaspard-Mecuson et al.
SURFACE & COATINGS TECHNOLOGY (2007)
Porosity in plasma electrolytic oxide coatings
JA Curran et al.
ACTA MATERIALIA (2006)
Oxide ceramic coatings on aluminium alloys produced by a pulsed bipolar plasma electrolytic oxidation process
AL Yerokhin et al.
SURFACE & COATINGS TECHNOLOGY (2005)
Characterization of fiber/matrix interface strength: applicability of different tests, approaches and parameters
S Zhandarov et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2005)
Cracking and decohesion of a thin Al2O3 film on a ductile Al-5%Mg substrate
CJ Xie et al.
ACTA MATERIALIA (2005)
Fabrication and structural performance of periodic cellular metal sandwich structures
HNG Wadley et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2003)
How can adhesion be determined from micromechanical tests?
E Pisanova et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2001)
Share Paper
