☆ 4.7 Article

Research on mechanical properties and failure mechanism of TRM composites via digital image correlation method and finite element simulation

COMPOSITE STRUCTURES (2023)

Related references

Note: Only part of the references are listed.

Article Construction & Building Technology

Effect of steel fiber-volume fraction and distribution on flexural behavior of Ultra-high performance fiber reinforced concrete by digital image correlation technique

Shaoqiang Meng et al.

Summary: This study investigates the impact of steel fiber volume fraction and distribution on the flexural behavior of UHPFRC, revealing a correlation between fiber distribution characteristics and flexural response. Increasing fiber volume fraction results in a more zigzag crack propagation path, significantly affecting the flexural behavior of UHPFRC.

CONSTRUCTION AND BUILDING MATERIALS (2022)

Add to Collection

Article Chemistry, Physical

Experimental Investigation of the TRM-to-Masonry Bond after Exposure to Elevated Temperatures: Cementitious and Alkali-Activated Matrices of Various Densities

Paraskevi D. Askouni et al.

Summary: Limited research has been done on the effect of high temperatures on the bond between textile-reinforced mortar (TRM) and masonry. In this study, masonry prisms with double-layered TRM strips were exposed to 200°C and 400°C for 1 hour and then tested under shear bond conditions. The results showed that exposure to elevated temperatures did not change the failure mode of the specimens. The residual bond capacity of the TRM systems decreased linearly with increasing temperature. The alkali-activated TRM systems performed better in terms of bond strength compared to cement-based systems. All systems retained approximately 50% of their original bond strength after heating at 400°C. Lightweight matrices provided comparable or better heat protection at the TRM/masonry interface depending on the type of binder.

MATERIALS (2022)

Add to Collection

Article Mechanics

Cyclic shear-compression testing of brick masonry walls repaired and retrofitted with basalt textile reinforced mortar

Larisa Garcia-Ramonda et al.

Summary: This study validated the effectiveness of using the B-TRM system to reinforce damaged masonry walls and improve their resistance and ductility, with results applicable for seismic retrofit and post-earthquake repair. Additionally, the research enhanced the understanding of the behavior mechanism and displacement capacity of masonry walls under cyclic horizontal displacement.

COMPOSITE STRUCTURES (2022)

Add to Collection

Article Mechanics

Flexural behavior of concrete slabs strengthened with textile reinforced geopolymer mortar

Hai Yan Zhang et al.

Summary: This paper presents experimental and numerical studies on the flexural behavior of RC one-way slabs strengthened with TRGM. The results show that TRGM can delay crack development and enhance flexural capacity of slabs, and increasing number of strengthening layers and decreasing spacing can increase the flexural capacity.

COMPOSITE STRUCTURES (2022)

Add to Collection

Article Materials Science, Multidisciplinary

In Situ Deformation of First Tarsometatarsal Arthrodesis Implants with Digital Image Correlation: A Cadaveric Study

Victor ChuYu Shen et al.

Summary: This study compared the biomechanical performance of two implant constructs in a matched-pair cadaveric model and found that the locking plate construct performed superiorly during loading compared to the nitinol staple construct.

JOM (2022)

Add to Collection

Article Mechanics

Assessment and modeling of the debonding failure of fabric-reinforced cementitious matrix (FRCM) systems

Ahmed Mandor et al.

Summary: This paper developed a model to predict debonding strains in reinforced concrete members strengthened with fabric-reinforced cementitious matrix systems. The study identified key parameters affecting debonding mechanisms and developed three models using nonlinear regression analysis to accurately predict debonding strains. Two of the models demonstrated excellent prediction performance, while neglecting the tensile strength of the concrete substrate in the third model resulted in a lower prediction accuracy.

COMPOSITE STRUCTURES (2021)

Add to Collection

Article Mechanics

Experimental and analytical study on the behavior of RC beams with externally bonded carbon-FRCM composites

Liangliang Wei et al.

Summary: The experimental results show that externally bonded carbon fabric reinforced cementitious matrix (carbonFRCM) can effectively enhance the load-carrying capacity of RC beams. For multilayer carbon-FRCM design, two layers of carbon fabric is an optimal choice. The utilization efficiency of carbon fabric is slightly higher in the fabric slippage failure compared to the peeling-off of concrete cover.

COMPOSITE STRUCTURES (2021)

Add to Collection

Article Computer Science, Interdisciplinary Applications

Damage-based finite-element modelling of in-plane loaded masonry walls repaired with FRCM

Jean-Patrick Plassiard et al.

Summary: Results of the study show that the masonry wall repair using textile reinforced mortar achieved recovery and even an increase in initial stiffness and strength. Finite-element simulations were conducted to assess the gain in strength for different degrees of wall damage, along with investigating crack patterns and effects of different repair configurations.

COMPUTERS & STRUCTURES (2021)

Add to Collection

Article Polymer Science

Catechol-modified epoxy coatings with high adhesive strength on saturated concrete substrate

Dewen Sun et al.

Summary: A series of catechol-modified epoxy resin biomimetic coatings with high adhesive strength on saturated concrete substrate were designed and synthesized. The adhesive properties can be improved by forming hydrogen bonds and coordination complexes in the interface of coating and saturated concrete substrate. Adding a proper amount of catechol groups can enhance the adhesive strength of epoxy coatings on saturated concrete substrate.

IRANIAN POLYMER JOURNAL (2021)

Add to Collection

Article Engineering, Multidisciplinary

Analyzing the effect of misalignment on single-filament carbon fiber tensile testing via stereoscopic computer vision imaging

Cole A. Love-Baker et al.

Summary: Understanding the constitutive properties of carbon fibers is crucial for high-resolution composite simulations and the development of low-cost alternative precursor materials. Single-fiber tensile testing is a useful tool for measuring CF properties, but challenges exist due to factors such as small fiber diameter, fiber brittleness, and required nanoscale/microscale resolution. Fiber misalignment is identified as a critical factor affecting the accuracy of measured properties, and a robust method of fiber alignment using stereoscopic computer vision is proposed to improve accuracy in testing.

MEASUREMENT SCIENCE AND TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Ceramics

Characterizing environment-dependent fracture mechanisms of ceramic matrix composites via digital image correlation

Clifton H. Bumgardner et al.

Summary: A novel methodology using in situ stereoscopic digital image correlation was employed to assess the fracture mechanics of SiC/SiC ceramic matrix composites. The study revealed that cracks propagate along the specimen length during hermeticity testing, and that heat treatment in open air results in decreased flexural properties and brittle failure.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Ceramics

Unveiling hermetic failure of ceramic tubes by digital image correlation and acoustic emission

Clifton H. Bumgardner et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2020)

Add to Collection

Article Engineering, Biomedical

3D digital image correlation evaluation of arthrodesis implants

Victor ChuYu Shen et al.

CLINICAL BIOMECHANICS (2020)

Add to Collection

Article Engineering, Multidisciplinary

Analysis of tow architecture variability in biaxially braided composite tubes

Frederick M. Heim et al.

COMPOSITES PART B-ENGINEERING (2020)

Add to Collection

Article Mechanics

Study on the flexural strengthening effect of RC beams reinforced by FRP grid with PCM shotcrete

Rui Guo et al.

COMPOSITE STRUCTURES (2020)

Add to Collection

Article Engineering, Multidisciplinary

Numerical simulation of the tensile behavior of FRCM strengthening systems

Ernesto Grande et al.

COMPOSITES PART B-ENGINEERING (2020)

Add to Collection

Article Engineering, Multidisciplinary

Quantifying the effect of tow architecture variability on the performance of biaxially braided composite tubes

Frederick M. Heim et al.

COMPOSITES PART B-ENGINEERING (2020)

Add to Collection

Article Mechanics

Tensile behaviour of glass FRCM systems with fabrics' overlap: Experimental results and numerical modeling

Jacopo Donnini et al.

COMPOSITE STRUCTURES (2019)

Add to Collection

Article Construction & Building Technology

Comparison of different types of TRM composites for strengthening masonry panels

Xuan Wang et al.

CONSTRUCTION AND BUILDING MATERIALS (2019)

Add to Collection

Article Mechanics

Ancient masonry arches and vaults strengthened with TRM, SRG and FRP composites: Experimental evaluation

Francesca Giulia Carozzi et al.

COMPOSITE STRUCTURES (2018)

Add to Collection

Article Mechanics

Out-of-plane maximum resisting bending moment of masonry walls strengthened with FRCM composites

T. D'Antino et al.

COMPOSITE STRUCTURES (2018)

Add to Collection

Article Mechanics

FRCM/internal transverse shear reinforcement interaction in shear strengthened RC beams

Tadesse G. Wakjira et al.

COMPOSITE STRUCTURES (2018)

Add to Collection

Article Engineering, Multidisciplinary

Mechanical performance of epoxy coated AR-glass fabric Textile Reinforced Mortar: Influence of coating thickness and formulation

Massimo Messori et al.

COMPOSITES PART B-ENGINEERING (2018)

Add to Collection

Article Engineering, Multidisciplinary

Effect of test setup on the fiber-to-mortar pull-out response in TRM composites: Experimental and analytical modeling

Ali Dalalbashi et al.

COMPOSITES PART B-ENGINEERING (2018)

Add to Collection

Article Engineering, Multidisciplinary

Numerical investigation on the bond behavior of FRCM strengthening systems

Ernesto Grande et al.

COMPOSITES PART B-ENGINEERING (2018)

Add to Collection

Article Engineering, Multidisciplinary

Fiber-to-mortar bond behavior in TRM composites: Effect of embedded length and fiber configuration

Ali Dalalbashi et al.

COMPOSITES PART B-ENGINEERING (2018)

Add to Collection

Article Construction & Building Technology

Comparison between different tensile test set-ups for the mechanical characterization of inorganic-matrix composites

T. D'Antino et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

Add to Collection

Article Materials Science, Ceramics

Scalable measurements of tow architecture variability in braided ceramic composite tubes

Frederick M. Heim et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2018)

Add to Collection

Review Construction & Building Technology

State-of-the-art on strengthening of masonry structures with textile reinforced mortar (TRM)

Leonidas Alexandros S. Kouris et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Uniting Strength and Toughness of Al Matrix Composites with Coordinated Al3Ni and Al3Ti Reinforcements

Frederick M. Heim et al.

ADVANCED ENGINEERING MATERIALS (2018)

Add to Collection

Article Materials Science, Composites

Experimental and numerical study on short eccentric columns strengthened by textile-reinforced concrete under sustaining load

Dejun Liu et al.

JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2017)

Add to Collection

Article Mechanics

Mechanical, thermal and interfacial performances of carbon fiber reinforced composites flavored by carbon nanotube in matrix/interface

Zhongbo Zhao et al.

COMPOSITE STRUCTURES (2017)

Add to Collection

Article Engineering, Multidisciplinary

Tensile behaviour of a basalt TRM strengthening system: Influence of mortar and reinforcing textile ratios

Carmelo Caggegi et al.

COMPOSITES PART B-ENGINEERING (2017)

Add to Collection

Article Engineering, Multidisciplinary

Experimental analysis on tensile and bond properties of PBO and aramid fabric reinforced cementitious matrix for strengthening masonry structures

Carmelo Caggegi et al.

COMPOSITES PART B-ENGINEERING (2017)

Add to Collection

Article Engineering, Multidisciplinary

Mechanical characterization of textile reinforced inorganic-matrix composites

T. D'Antino et al.

COMPOSITES PART B-ENGINEERING (2017)

Add to Collection

Article Engineering, Multidisciplinary

Experimental investigation of tuff masonry panels reinforced with surface bonded basalt textile-reinforced mortar

Giancarlo Marcari et al.

COMPOSITES PART B-ENGINEERING (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Multi-level characterization of steel reinforced mortars for strengthening of masonry structures

Bahman Ghiassi et al.

MATERIALS & DESIGN (2016)

Add to Collection

Article Engineering, Civil

Using digital image correlation to evaluate fatigue behavior of strengthened reinforced concrete beams

Mohammed Mahal et al.

ENGINEERING STRUCTURES (2015)

Add to Collection

Article Engineering, Multidisciplinary

Mechanical behaviour of ultra-high-performance fibrous-concrete wood panels reinforced by FRP bars

E. Ferrier et al.

COMPOSITES PART B-ENGINEERING (2014)

Add to Collection

Article Mechanics

Flexural strengthening of RC beams using textile reinforced mortar - Experimental and numerical study

Hussein M. Elsanadedy et al.

COMPOSITE STRUCTURES (2013)

Add to Collection

Article Engineering, Civil

Experimental and Numerical Study for the Shear Strengthening of Reinforced Concrete Beams Using Textile-Reinforced Mortar

Yousef A. Al-Salloum et al.

JOURNAL OF COMPOSITES FOR CONSTRUCTION (2012)

Add to Collection

Review Engineering, Civil

Maintenance, management, life-cycle design and performance of structures and infrastructures: a brief review

Dan M. Frangopol et al.

STRUCTURE AND INFRASTRUCTURE ENGINEERING (2012)

Add to Collection

Article Materials Science, Multidisciplinary

Analysis of Cracks and Deformations in a Full Scale Reinforced Concrete Beam Using a Digital Image Correlation Technique

J. -F. Destrebecq et al.

EXPERIMENTAL MECHANICS (2011)

Add to Collection

Review Mechanics

Application of polymer composites in civil construction: A general review

Sandeep S. Pendhari et al.

COMPOSITE STRUCTURES (2008)

Add to Collection

Article Construction & Building Technology

Use of FRP composites in civil structural applications

L Van Den Einde et al.

CONSTRUCTION AND BUILDING MATERIALS (2003)

Add to Collection

© Peeref 2019-2024. All rights reserved.