☆ 4.7 Article

Ultrafast high-temperature sintering of polymer-derived ceramic nanocomposites for high-temperature thin-film sensors

CHEMICAL ENGINEERING JOURNAL (2023)

Related references

Note: Only part of the references are listed.

Article Chemistry, Multidisciplinary

Abnormal Graphitization Behavior in Near-Surface/Interface Region of Polymer-Derived Ceramics

Chao Wu et al.

Summary: This study investigates the phenomenon of the graphitization of free carbon in polymer-derived ceramics (PDCs) and uncovers the crucial role of surface/interface interactions in regulating carbon and its properties. Due to the enrichment behavior of free carbon in the near-surface/interface region, PDCs exhibit highly abnormal properties, such as the behavior of the current and the edge effect. These surface/interface interactions are of great significance for the applications of PDCs.

SMALL (2023)

Add to Collection

Article Engineering, Environmental

Ultrafast sintering of Na3Zr2Si2PO12 solid electrolyte for long lifespan solid-state sodium ion batteries

Pengfeng Jiang et al.

Summary: The smart manufacturing of solid-state electrolytes (SSEs) is crucial for the assembly and performance improvement of solid-state batteries. This study employed an ultrafast high-temperature sintering method to prepare Na3Zr2Si2PO12 ceramic SSEs with high ionic conductivity. The prepared SSEs exhibited excellent electrochemical performance.

CHEMICAL ENGINEERING JOURNAL (2023)

Add to Collection

Article Engineering, Environmental

Temperature-insensitive conductive composites for noninterference strain sensing

Chao Wu et al.

Summary: In this study, a new temperature-insensitive material was developed by controlling electron scattering and thermally assisted hopping transport in conductive composites, which successfully eliminated environmental interference owing to temperature fluctuations. The proposed material enables noninterference dynamic strain monitoring over an ultrawide temperature range of 30-300 degrees C.

CHEMICAL ENGINEERING JOURNAL (2023)

Add to Collection

Article Materials Science, Ceramics

Influence of substrate temperature on the microstructure of YSZ films and their application as the insulating layer of thin film sensors for harsh temperature environments

Hao Liu et al.

Summary: The electrical insulation characteristics of a YSZ/Al2O3 multilayer insulating structure were investigated for the purpose of improving the insulation properties and adhesion of thin film sensors used to monitor the health of hot-section components of aeroengine intelligence. The results showed that the YSZ thin film with compact and uniform topography significantly enhanced the insulation resistance of the multilayer insulating structure. The YSZ/Al2O3 multilayer insulating structure was found to be suitable for thin film sensors, as demonstrated by the low relative resistance error.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Ceramics

High-temperature electrical properties of polymer-derived ceramic SiBCN thin films fabricated by direct writing

Chao Wu et al.

Summary: In this study, SiBCN thin-film resistance grids were fabricated and tested for their resistance-temperature characteristics, stability, and repeatability in high-temperature environments. The results showed that the SiBCN films exhibited excellent oxidation resistance and electrical conductivity, making them suitable for in situ temperature monitoring of hot components in harsh environments.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Ceramics

Electromagnetic wave absorption properties of polymer-derived magnetic carbon-rich SiCN-based composite ceramics

Shan Wang et al.

Summary: This paper discusses the preparation of carbon-rich SiCN-based composite ceramics by adding a mixture of Fe and Ni nanoparticles to liquid polysilazane. The addition of magnetic particles improves the impedance matching and magnetic loss performance of the composite ceramics. Furthermore, the formation of carbon nanotubes through FeNi catalysis enhances the dielectric loss ability. As a result, the electromagnetic wave absorption performance of the composite ceramics is significantly improved.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Review Materials Science, Ceramics

Advances in ultra-high temperature ceramics, composites, and coatings

Dewei Ni et al.

Summary: Ultra-high temperature ceramics (UHTCs) have ultra-high melting points, outstanding mechanical properties, and ablation resistance at elevated temperatures, making them promising materials for structural applications in extreme environments such as rockets and hypersonic vehicles. The development of high-entropy UHTCs is an emerging direction for ultra-high temperature materials.

JOURNAL OF ADVANCED CERAMICS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Microstrain-range giant piezoresistivity of silicon oxycarbide thin films under mechanical cyclic loads

Emmanuel Ricohermoso et al.

Summary: In this study, thin-film strain gauge element arrays were prepared using large-area silicon oxycarbide thin films and structured electrodes. The strain gauge elements exhibited giant piezoresistivity with excellent reversibility and short response times, indicating great potential for MEMS-related applications.

MATERIALS & DESIGN (2022)

Add to Collection

Article Materials Science, Ceramics

TiB2-modified PDC electrical solder joints for electrical interconnection in extreme environments

Chao Wu et al.

Summary: In this study, TiB2-modified PDC electrical solder joints were developed for electrical interconnections in harsh environments, exhibiting extremely low resistance, reliable electrical connection, and oxidation resistance at high temperatures.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Engineering, Environmental

Microencapsulation of high temperature metallic phase change materials with SiCN shell

Kaichen Wang et al.

Summary: Metallic phase change materials (PCMs) have broad application prospects, but corrosion at high temperature is a problem. This research proposed a high temperature PCM microencapsulating technology with SiCN shell and prepared MEPCMs with different core-shell mass ratios. The experimental results showed that MEPCMs with a core-shell mass ratio of 4:1 had high phase change temperature and good heat storage capability.

CHEMICAL ENGINEERING JOURNAL (2022)

Add to Collection

Article Engineering, Environmental

Additive manufacturing of nanocellulose/polyborosilazane derived CNFs-SiBCN ceramic metamaterials for ultra-broadband electromagnetic absorption

Heqiang Liu et al.

Summary: This study develops modified SiBCN ceramic-based metamaterials with defect-rich carbon nanofibers (CNFs) using additive manufacturing and polymer derived ceramic route. The materials exhibit high permittivity and strong polarization capability with suitable cellulose content and annealing temperature. Additionally, the materials show excellent absorption performance at different thicknesses.

CHEMICAL ENGINEERING JOURNAL (2022)

Add to Collection

Article Materials Science, Ceramics

Thin-film temperature sensor made from particle-filled polymer-derived ceramics pyrolyzed in vacuum

Zaifu Cui et al.

Summary: This study proposes the pyrolysis of polymer-derived ceramics (PDC) thin films in vacuum to solve the oxidation issue and verifies its application in high-temperature sensors. It provides a feasible method for the fabrication of high-temperature PDC thin-film sensors.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Editorial Material Materials Science, Ceramics

Ultrafast high-temperature sintering offers rapid, pressureless production of high-quality glasses

[Anonymous]

AMERICAN CERAMIC SOCIETY BULLETIN (2022)

Add to Collection

Article Materials Science, Ceramics

The role of carbon in microstructure evolution of SiBCO ceramics

Xiwen Xia et al.

Summary: This article investigates the effect of carbon content in SiBCO polymer precursors. It is found that carbon contributes to the formation of graphitic carbon and has a significant impact on the microstructure evolution of ceramics.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Upscaling Ultrafast High-Temperature Sintering (UHS) to consolidate large-sized and complex-shaped ceramics

Fei Zuo et al.

Summary: This study proposes a novel Ultrafast High-temperature Sintering (UHS) configuration using graphite powder medium, which allows for the production of larger and complex-shaped ceramic products with fast sintering rate and fine tuning of microstructures.

SCRIPTA MATERIALIA (2022)

Add to Collection

Article Engineering, Electrical & Electronic

TiB2/SiCN Thin-Film Strain Gauges Fabricated by Direct Writing for High-Temperature Application

Chao Wu et al.

Summary: In this study, TiB2/SiCN thin-film strain gauges were fabricated on nickel base alloy substrates for in situ strain monitoring of hot components. The results show that these ceramic-based strain gauges exhibit excellent thermal stability and strain response, with an operating temperature of up to 700 degrees C.

IEEE SENSORS JOURNAL (2022)

Add to Collection

Article Materials Science, Ceramics

Ultrafast high-temperature heating in air

Yihan Liang et al.

Summary: In this study, a novel configuration for ultrafast high-temperature heating in air using commercial graphite paper is presented. This configuration enables stable high temperatures and ultrafast heating rates. By considering different heating profiles, ultrafast high-temperature sintering with tunable microstructures is demonstrated.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Engineering, Environmental

Sensitivity enhanced, highly stretchable, and mechanically robust strain sensors based on reduced graphene oxide-aramid nanofibers hybrid fillers

Yankun Lin et al.

Summary: In this study, a sensitivity enhanced, highly stretchable, and mechanically robust strain sensor based on RGO-ANFs hybrid fillers and NR matrix was proposed. The strain sensor exhibited improved sensing performance, wide detection range, expected mechanical properties, excellent stability and repeatability, as well as fast feedback. It could monitor joint movements and physiological activities in real time under various temperature conditions.

CHEMICAL ENGINEERING JOURNAL (2022)

Add to Collection

Article Chemistry, Analytical

Additive-Manufactured Platinum Thin-Film Strain Gauges for Structural Microstrain Testing at Elevated Temperatures

Xiaochuan Pan et al.

Summary: This paper investigates the feasibility and performance of fabricating platinum high-temperature thin-film strain sensors on nickel-based alloy substrates using additive manufacturing. The results show that the fabricated sensors have good static and dynamic strain responses, making them suitable for in-situ strain monitoring of high-temperature complex components.

MICROMACHINES (2022)

Add to Collection

Article Chemistry, Physical

Manufacturing smart surfaces with embedded sensors via magnetron sputtering and laser scribing

Javier Diez-Sierra et al.

Summary: Magnetron sputtering combined with laser scribing enables the manufacturing of thin film sensors/actuators embedded on component surfaces, adding active monitoring and actuation capabilities. The process involves coating the target surface with an insulator layer and a metallic conductor layer, and selectively removing the conductor to create an isolated circuit using laser scribing. This technology allows for high-precision and adhesive-free sensors that can be located in components with complex geometries.

APPLIED SURFACE SCIENCE (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Rapid Pressureless Sintering of Glasses

Zhiwei Lin et al.

Summary: This study reports an ultrafast high-temperature sintering (UHS) technique for the rapid fabrication of high-quality silica glass. Using UHS, silica precursors can be densified within seconds, resulting in sintered glasses with high relative densities and high visible transmittances. The UHS technique can also be extended to sinter other functional glasses and transparent ceramics.

SMALL (2022)

Add to Collection

Article Materials Science, Ceramics

Compressive thermal stress and microstructure-driven charge carrier transport in silicon oxycarbide thin films

Emmanuel Ricohermoso et al.

Summary: This study investigates the charge carrier transport mechanism in silicon oxycarbide thin films, finding that highly-graphitized carbon-rich areas are dispersed within an oxygen-rich matrix, leading to compressive biaxial stress. Hall measurements show p-type carriers dominating the SiOC film, with carrier mobility two magnitudes higher than in monolithic samples. The improved conductivity of the SiOC thin film is attributed to enhanced carrier mobility and a reduced percolation threshold due to the phase-separated morphology.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Ultrafast high-temperature sintering of bulk oxides

Rui-Fen Guo et al.

Summary: By employing the innovative ultrafast high-temperature sintering technique, ceramic densification can be achieved in a very short time, which accelerates the material screening rate and facilitates the development of novel materials.

SCRIPTA MATERIALIA (2021)

Add to Collection

Article Engineering, Electrical & Electronic

Polymer-derived ceramic thin-film temperature sensor

Zaifu Cui et al.

Summary: This work successfully addresses the monitoring challenges of machines in harsh environments by fabricating an ultra-thin-film temperature sensor, providing a new solution for aerospace applications.

SENSORS AND ACTUATORS A-PHYSICAL (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Rapid Synthesis and Sintering of Metals from Powders

Chengwei Wang et al.

Summary: Powder to bulk processing techniques like additive manufacturing and metal injection molding have revolutionized complex metal design and manufacturing. However, they often face challenges like residue stress and slow sintering processes. The ultrafast high-temperature sintering process offers a quick solution for synthesizing and sintering bulk metals and alloys, allowing for rapid screening and development of new metal compositions and structures.

ADVANCED SCIENCE (2021)

Add to Collection

Article Materials Science, Ceramics

Fast pyrolysis of a SiC-based polymer precursor using a spark plasma sintering apparatus-Effects of heating methods and pyrolysis atmosphere

Jian Gu et al.

Summary: The heating method significantly affects the pyrolysis behavior, crystallinity, and ceramic yield of SiC-based precursor-derived ceramics. SPS results in higher crystallinity and shorter processing time compared to the tube furnace method. The study demonstrates a promising approach for pyrolyzing ceramic precursors with improved thermal stability.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Chemistry, Multidisciplinary

3D Printed Graphene-Based 3000 K Probe

Zhiqiang Liang et al.

Summary: The study introduces a novel method of small-scale heating using 3D printed RGO probes, achieving precise heating with high spatial and temporal resolutions. The research demonstrates the selective synthesis of metal nanoparticles such as platinum and silver on nano-carbon substrates, which is not achievable by traditional steady-state heating.

ADVANCED FUNCTIONAL MATERIALS (2021)

Add to Collection

Article Chemistry, Multidisciplinary

High-Temperature Ultrafast Sintering: Exploiting a New Kinetic Region to Fabricate Porous Solid-State Electrolyte Scaffolds

Ruiliu Wang et al.

Summary: The method described in the text offers a simple and efficient way to fabricate 3D porous scaffolds with ceramic solid-state electrolytes, allowing for rapid sintering of the desired crystalline phase and control over densification. This approach is suitable for various applications in all-solid-state batteries.

ADVANCED MATERIALS (2021)

Add to Collection

Review Materials Science, Multidisciplinary

The fate and role of in situ formed carbon in polymer-derived ceramics

Qingbo Wen et al.

PROGRESS IN MATERIALS SCIENCE (2020)

Add to Collection

Article Materials Science, Ceramics

Electrical insulation improvements of ceramic coating for high temperature sensors embedded on aeroengine turbine blade

Haotian Weng et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Materials Science, Ceramics

Electrospun SiOC ceramic fiber mats as freestanding electrodes for electrochemical energy storage applications

Shakir Bin Mujib et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Multidisciplinary Sciences

High-throughput, combinatorial synthesis of multimetallic nanoclusters

Yonggang Yao et al.

PROCEEDINGS OF THE NATIONAL ACADEMY OF SCIENCES OF THE UNITED STATES OF AMERICA (2020)

Add to Collection

Article Multidisciplinary Sciences

A general method to synthesize and sinter bulk ceramics in seconds

Chengwei Wang et al.

SCIENCE (2020)

Add to Collection

Article Chemistry, Multidisciplinary

Thermal Shock Synthesis of Nanocatalyst by 3D-Printed Miniaturized Reactors

Yun Qiao et al.

SMALL (2020)

Add to Collection

Article Chemistry, Multidisciplinary

Computation-Guided Synthesis of New Garnet-Type Solid-State Electrolytes via an Ultrafast Sintering Technique

Ruiliu Wang et al.

ADVANCED MATERIALS (2020)

Add to Collection

Review Materials Science, Multidisciplinary

What's new in ceramics sintering? A short report on the latest trends and future prospects

Mattia Biesuz et al.

CURRENT OPINION IN SOLID STATE & MATERIALS SCIENCE (2020)

Add to Collection

Article Chemistry, Analytical

Development, Characterisation and High-Temperature Suitability of Thin-Film Strain Gauges Directly Deposited with a New Sputter Coating System

Daniel Klaas et al.

SENSORS (2020)

Add to Collection

Article Chemistry, Multidisciplinary

High-Temperature Pulse Method for Nanoparticle Redispersion

Hua Xie et al.

JOURNAL OF THE AMERICAN CHEMICAL SOCIETY (2020)

Add to Collection

Article Multidisciplinary Sciences

Printable, high-performance solid-state electrolyte films

Weiwei Ping et al.

SCIENCE ADVANCES (2020)

Add to Collection

Article Engineering, Electrical & Electronic

Effect of thickness on the electrical properties of PdCr strain sensitive thin film

Hao Liu et al.

JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS (2019)

Add to Collection

Article Engineering, Electrical & Electronic

High temperature static and dynamic strain response of PdCr thin film strain gauge prepared on Ni-based superalloy

Hao Liu et al.

SENSORS AND ACTUATORS A-PHYSICAL (2019)

Add to Collection

Article Engineering, Environmental

Thermostable SiCO@BN sheets with enhanced electromagnetic wave absorption

Yongzhao Hou et al.

CHEMICAL ENGINEERING JOURNAL (2019)

Add to Collection

Article Materials Science, Ceramics

Preparation and the effects of ion irradiation on bulk SiOC ceramics

Zihao Zhao et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Add to Collection

Article Chemistry, Multidisciplinary

Recent Advances in Mechanism Research and Methods for Electric-Field-Assisted Sintering of Ceramics

Mattan Ze'ev Becker et al.

ADVANCED MATERIALS (2018)

Add to Collection

Article Engineering, Environmental

Lightweight, flexible SiCN ceramic nanowires applied as effective microwave absorbers in high frequency

Peng Wang et al.

CHEMICAL ENGINEERING JOURNAL (2018)

Add to Collection

Article Chemistry, Physical

Effect of Al2O3/Al bilayer protective coatings on the high-temperature stability of PdCr thin film strain gages

Shenyong Yang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Article Chemistry, Physical

Fabrication of a thin double-layer thermistor based on DVB-modified polymer-derived SiCN ceramics

Baisheng Ma et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Article Engineering, Electrical & Electronic

YSZ/Al2O3 multilayered film as insulating layer for high temperature thin film strain gauge prepared on Ni-based superalloy

Hao Liu et al.

SENSORS AND ACTUATORS A-PHYSICAL (2018)

Add to Collection

Article Engineering, Electrical & Electronic

Polymer-derived SiAlOC ceramic pressure sensor with potential for high-temperature application

Ni Li et al.

SENSORS AND ACTUATORS A-PHYSICAL (2017)

Add to Collection

Proceedings Paper Instruments & Instrumentation

Preparation and evaluation of PdCr thin film resistive strain gauges

Hao Liu et al.

6TH INTERNATIONAL CONFERENCE ON MATERIALS AND APPLICATIONS FOR SENSORS AND TRANSDUCERS, (IC-MAST 2016) (2017)

Add to Collection

Article Materials Science, Ceramics

Electrical insulation of ceramic thin film on metallic aero-engine blade for high temperature sensor applications

Junchao Gao et al.

CERAMICS INTERNATIONAL (2016)

Add to Collection

Article Materials Science, Ceramics

Microwave Absorption of SiC/HfCxN1-x/C Ceramic Nanocomposites with HfCxN1-x-Carbon Core-Shell Particles

Qingbo Wen et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2016)

Add to Collection

Article Materials Science, Coatings & Films

Preparation, characterization and application of high-temperature Al2O3 insulating film

Di Niu et al.

SURFACE & COATINGS TECHNOLOGY (2016)

Add to Collection

Article Physics, Applied

Wireless passive polymer-derived SiCN ceramic sensor with integrated resonator/antenna

Yan Li et al.

APPLIED PHYSICS LETTERS (2013)

Add to Collection

Article Engineering, Electrical & Electronic

Near-Field Electrospray Microprinting of Polymer-Derived Ceramics

Hongxu Duan et al.

JOURNAL OF MICROELECTROMECHANICAL SYSTEMS (2013)

Add to Collection

Article Engineering, Electrical & Electronic

Fabrication and electrical properties of polymer-derived ceramic (PDC) thin films for high-temperature heat flux sensors

Duckbong Seo et al.

SENSORS AND ACTUATORS A-PHYSICAL (2011)

Add to Collection

© Peeref 2019-2024. All rights reserved.