☆ 4.7 Article

Wear performance of Ti-6Al-4 V titanium alloy through nano-doped lubricants

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2023)

Related references

Note: Only part of the references are listed.

Article Engineering, Biomedical

Wear behavior of materials for additive manufacturing after simulated occlusion of deciduous dentition

Yujeong Shin et al.

JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2023)

Add to Collection

Article Engineering, Mechanical

Wear and Friction Mechanism of Stainless Steel 420 Under Various Lubrication Conditions: A Tribological Assessment With Ball on Flat Test

Munish Kumar Gupta et al.

Summary: The wear mechanism of stainless steel 420 is influenced by the adhesion and abrasion between contact surfaces when using 100Cr6 balls. This study conducted ball-on-flat experiments on stainless steel 420 and 100Cr6 friction pairs under different conditions, and examined wear properties including volume loss, profile tracks, micrographs, and coefficient of friction. The results showed that the use of minimum quantity lubrication (MQL) and pool conditions improved the tribological properties of stainless steel 420 against 100Cr6 ball.

JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2023)

Add to Collection

Article Engineering, Civil

Fracture toughness, wear, and microstructure properties of aluminum/titanium/steel multi-laminated composites produced by cross-accumulative roll-bonding process

Yaping Wang et al.

Summary: This paper investigates the microstructure and mechanical properties of aluminum/titanium/steel multi-laminated composites fabricated by the CARB process. Increasing the number of rolling passes resulted in more instabilities, decreased ultimate and yield strength, decreased elongation, and changes in fracture toughness and wear mechanisms.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Tribological and rheological evaluation of a graphene nanosheets-based lubricant for metal-on-metal and wet clutch interfaces

Julio A. Cao-Romero-Gallegos et al.

Summary: This study analyzed the tribological and rheological behavior of mineral oil additivated with graphene nano-sheets as a lubricant, focusing on its potential application in automatic transmission systems. The addition of graphene nano-sheets made the lubricants non-Newtonian shear-thinning, increased viscosity at high shear rates, reduced wear rate for metallic interfaces, and enhanced the thermal stability and anti-shudder property of wet clutches.

MATERIALS LETTERS (2022)

Add to Collection

Article Engineering, Chemical

Thermophysical, rheological and electrical properties of mono and hybrid TiB2/B4C nanofluids based on a propylene glycol:water mixture

Javier P. Vallejo et al.

Summary: In this study, mono B4C and TiB2 and hybrid TiB2:B4C nanoadditives were used to design nanofluids for the first time, with B4C mono nanofluid showing the highest improvements in thermal conductivity and electrical conductivity, but also the highest viscosity increases. The hybrid nanofluid displayed intermediate values for most properties between the mono nanofluids, except for dynamic viscosity.

POWDER TECHNOLOGY (2022)

Add to Collection

Article Engineering, Mechanical

Understanding the lubrication regime phenomenon and its influence on tribological characteristics of additively manufactured 316 Steel under novel lubrication environment

Mehmet Erdi Korkmaz et al.

Summary: This study focuses on the lubrication regime phenomena and its influence on the tribological characteristics of additively manufactured 316 steel under a novel lubrication environment. The results show that the hybrid cryo+MQL condition can provide a good lubrication film, leading to improved tribological properties.

TRIBOLOGY INTERNATIONAL (2022)

Add to Collection

Review Engineering, Mechanical

Inorganic nanomaterial lubricant additives for base fluids, to improve tribological performance: Recent developments

Junhai Wang et al.

Summary: This paper reviews recent research developments regarding the tribological performances of a series of inorganic nano-additives in lubricating fluids. It examines various types of inorganic nanomaterials, summarizes their lubrication mechanisms, identifies factors affecting tribological performance, and discusses challenges and future research directions. The review offers new perspectives to improve understanding of inorganic nano-additives in tribology and new approaches to expand their practical applications.

FRICTION (2022)

Add to Collection

Article Engineering, Mechanical

The synergistic effect of MAO-treated and PAO-graphene oil on tribological properties of Ti6Al4V alloys

Dongya Zhang et al.

Summary: In this study, MAO coatings were fabricated on Ti6Al4V surface, and modified graphene was used as an oil additive, which effectively enhanced the tribological properties and reduced the friction coefficients. The friction coefficient of Ti6Al4V lubricated with modified oil was lower than that of Ti6Al4V lubricated with PAO-MGr synthetic oils.

WEAR (2022)

Add to Collection

Article Engineering, Manufacturing

Novel design of MXene@UiO-66-NH2 hybrid nanofluids towards promoting the mechanical and tribological performance of fabric composites

Meng Liu et al.

Summary: In this study, MXene@UiO-66-NH2 nanofluids were synthesized by anchoring UiO-66-NH2 nanoparticles onto MXene nanosheets, followed by further functionalization. The introduction of MXene@UiO-66-NH2 nanofluids effectively reduced the friction and wear of fabric composites.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2022)

Add to Collection

Article Engineering, Mechanical

A novel use of hybrid Cryo-MQL system in improving the tribological characteristics of additively manufactured 316 stainless steel against 100 Cr6 alloy

Recep Demirsoz et al.

Summary: This study focuses on the tribological behavior of 316 L stainless steel against 100 Cr6 alloy under various cooling environments, finding that the combination of cryo and MQL cooling conditions can improve tribological performance while minimizing material volume loss and wear rates.

TRIBOLOGY INTERNATIONAL (2022)

Add to Collection

Article Engineering, Civil

Effect of cutting process adjustment on crystallographic texture of machined surface layer of titanium alloy

Anhai Li et al.

Summary: This paper investigates the surface quality control methods in titanium alloy machining, proposes two machining process adjustment methods, carries out finite element simulation, and validates the results through experiments.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2022)

Add to Collection

Article Green & Sustainable Science & Technology

Convective Heat Transfer Coefficient Model Under Nanofluid Minimum Quantity Lubrication Coupled with Cryogenic Air Grinding Ti-6Al-4V

Jianchao Zhang et al.

Summary: A new environmentally sustainable approach, CNMQL, is proposed to address the unfavorable lubricating characteristic of cryogenic air and the deficient cooling performance of minimum quantity lubrication. A convective heat transfer coefficient model was established to investigate the heat transfer mechanism of vortex tube cold air fraction by CNMQL. Experimental verification showed that when the cold air fraction was 0.35, nanofluids exhibited low specific grinding energy, high viscosity, and a large contact angle.

INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING-GREEN TECHNOLOGY (2021)

Add to Collection

Article Engineering, Mechanical

Tribological characterization of ZnO nanofluids as fastener lubricants

Xue Han et al.

Summary: Thread galling is a common problem when tightening fasteners, and in this study, the potential of zinc oxide nanofluids as thread lubricants was investigated. By finding suitable surfactants for dispersing and stabilizing the nanoparticles, the goal is to eliminate or minimize galling. PIBSA mixed with ZnO nanoparticles showed superior dispersion and stability compared to OA mixed with ZnO nanoparticles.

WEAR (2021)

Add to Collection

Article Engineering, Manufacturing

Effects of hybrid nanofluids on machining performance in MQL-milling of Inconel X-750 superalloy

Senol Sirin et al.

Summary: The study investigated the machining performance of Inconel X-750 superalloy using nanoparticles with different shapes and properties. It was found that the hybrid nanofluid hBN/Grpt outperformed other hybrid conditions, showing significant improvement in tool life.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Mechanical

Vibration signatures in ball bearings as a function of lubricant viscosity ratio κ, under alternating lubrication conditions

Morten Opprud Jakobsen et al.

Summary: This paper analyzes the vibrations emitted by a set of grease lubricated ball bearings run under load, when lubrication conditions alternate between good and insufficient. The study shows a good correlation between the lubrication ratio κ and spectral kurtosis for a given frequency band, both when the bearing is new and when κ is below 0.6.

TRIBOLOGY INTERNATIONAL (2021)

Add to Collection

Article Engineering, Multidisciplinary

Tribological behaviors of novel epoxy nanocomposites filled with solvent-free ionic SiO2 nanofluids

Yuexia Guo et al.

Summary: The addition of SiO2 nanofluids into epoxy resin greatly improves the tribological performance, forming a nanostructured tribofilm on the steel surface. The growth of the load-bearing tribofilm is essential for enhancing the tribological performance of the EP nanocomposite.

COMPOSITES PART B-ENGINEERING (2021)

Add to Collection

Article Energy & Fuels

Viscosity, tribological and physicochemical features of ZnO and MoS2 diesel oil-based nanofluids: An experimental study

Seyed Borhan Mousavi et al.

Summary: The study investigated the effects of temperature and nanoparticle content on the viscosity, tribological properties, and physicochemical features of diesel oil-based nanofluids. ZnO and MoS2 nanoparticles were found to enhance the tribological characteristics of pure diesel oil. The addition of nanoparticles also increased the pumping power.

FUEL (2021)

Add to Collection

Article Materials Science, Ceramics

A tribological investigation of SLM fabricated TC4 titanium alloy with carburization pre-treatment

Wenlong Yang et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Engineering, Mechanical

Investigation of hard turning performance of eco-friendly cooling strategies: Cryogenic cooling and nanofluid based MQL

Cagri Vakkas Yildirim

TRIBOLOGY INTERNATIONAL (2020)

Add to Collection

Article Green & Sustainable Science & Technology

New approach for cooling and lubrication in dry machining on the example of internal cylindrical grinding of bearing rings

Krzysztof Nadolny et al.

SUSTAINABLE MATERIALS AND TECHNOLOGIES (2020)

Add to Collection

Review Multidisciplinary Sciences

Nanotechnology implications for high performance lubricants

Deepika

SN APPLIED SCIENCES (2020)

Add to Collection

Article Engineering, Mechanical

Dispersing mechanism and tribological performance of vegetable oil-based CNT nanofluids with different surfactants

Teng Gao et al.

TRIBOLOGY INTERNATIONAL (2019)

Add to Collection

Article Automation & Control Systems

Tribological properties under the grinding wheel and workpiece interface by using graphene nanofluid lubricant

Xin Cui et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

Add to Collection

Review Engineering, Mechanical

Dispersion of Nanoparticles in Lubricating Oil: A Critical Review

Yan Chen et al.

LUBRICANTS (2019)

Add to Collection

Article Automation & Control Systems

Performance evaluation of Ti-6Al-4V machining using nano-cutting fluids under minimum quantity lubrication

H. Hegab et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Chemistry, Physical

Lubrication Performance of Graphene as Lubricant Additive in 4-n-pentyl-4 '-cyanobiphyl Liquid Crystal (5CB) for Steel/Steel Contacts

Zhiliang Li et al.

MATERIALS (2018)

Add to Collection

Article Engineering, Manufacturing

Performance evaluation of Ti-6Al-4V grinding using chip formation and coefficient of friction under the influence of nanofluids

Dinesh Setti et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2015)

Add to Collection

Article Green & Sustainable Science & Technology

Experimental evaluation of MoS2 nanoparticles in jet MQL grinding with different types of vegetable oil as base oil

Yanbin Zhang et al.

JOURNAL OF CLEANER PRODUCTION (2015)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of Particle Size and Ligand on the Tribological Properties of Amino Functionalized Hairy Silica Nanoparticles as an Additive to Polyalphaolefin

Tianyi Sui et al.

JOURNAL OF NANOMATERIALS (2015)

Add to Collection

Article Engineering, Mechanical

Wear behaviour of hydrogenated DLC in a pin-on-disc model test under lubrication with different diesel fuel types

Martin H. Djoufack et al.

TRIBOLOGY INTERNATIONAL (2015)

Add to Collection

Proceedings Paper Engineering, Multidisciplinary

Tribological behaviour of a lubricant oil containing boron nitride nanoparticles

Qingming Wan et al.

NEW PARADIGM OF PARTICLE SCIENCE AND TECHNOLOGY, PROCEEDINGS OF THE 7TH WORLD CONGRESS ON PARTICLE TECHNOLOGY (2015)

Add to Collection

Article Engineering, Civil

Heat transfer characteristics of silver/water nanofluids in a shell and tube heat exchanger

L. Godson et al.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Preparation, characterization, viscosity, and thermal conductivity of nitrogen-doped graphene aqueous nanofluids

Mohammad Mehrali et al.

JOURNAL OF MATERIALS SCIENCE (2014)

Add to Collection

Article Engineering, Chemical

Understanding the Role of Nanoparticles in Nano-oil Lubrication

Kwangho Lee et al.

TRIBOLOGY LETTERS (2009)

Add to Collection

Article Chemistry, Multidisciplinary

Synthetic Routes and Formation Mechanisms of Spherical Boron Nitride Nanoparticles

Chengchun Tang et al.

ADVANCED FUNCTIONAL MATERIALS (2008)

Add to Collection

Article Engineering, Mechanical

Experimental analysis of tribological properties of lubricating oils with nanoparticle additives

Y. Y. Wu et al.

WEAR (2007)

Add to Collection

Article Engineering, Mechanical

Microstructure and tribological properties of Al-Pb alloy modified by high current pulsed electron beam

J. An et al.

WEAR (2006)

Add to Collection

Article Instruments & Instrumentation

Improvement of tribological behavior of a Ti-Al-Zr alloy by nitrogen ion implantation

Y. Z. Liu et al.

NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION B-BEAM INTERACTIONS WITH MATERIALS AND ATOMS (2006)

Add to Collection

Article Chemistry, Physical

Hybrid organic -: inorganic catalysts:: a cooperative effect between support, and palladium and nickel salen complexes on catalytic hydrogenation of imines

V Ayala et al.

JOURNAL OF CATALYSIS (2004)

Add to Collection

Article Engineering, Mechanical

Tribological properties of WS2 nanoparticles under mixed lubrication

L Rapoport et al.

WEAR (2003)

Add to Collection

Article Engineering, Mechanical

Measurement of the potential of static electricity generated by the friction of oil lubricated metal on metal

A Sasaki et al.

TRIBOLOGY TRANSACTIONS (2002)

Add to Collection

© Peeref 2019-2024. All rights reserved.