☆ 4.6 Article

A Perspective on Emerging and Future Sintering Technologies of Ceramic Materials

ADVANCED ENGINEERING MATERIALS (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Room temperature stability, structure and mechanical properties of cubic tungsten carbide in flash sintered products

Isacco Mazo et al.

Summary: This study investigates the possibility of obtaining the metastable cubic tungsten car-bide phase (WC1-x) through rapid and ultra-rapid consolidation of hexagonal WC nanopowders. Spark plasma sintering and flash sintering techniques were used to study the formation and stability of WC(1-x) during sintering. Flash sintering process uniquely yields a biphasic ceramic material composed of cubic-WC/hex-WC(10/90 vol%). Ultrafast sintering of powders with Cr and V impurities results in a peculiar cubic WC quaternary phase (W0.87Cr0.12V0.09)C(0.71) that retains the metastable character of WC1-x but decomposes into thermodynamically stable hexagonal phases after annealing.

JOURNAL OF MATERIALS SCIENCE (2023)

Add to Collection

Article Materials Science, Ceramics

Synthesis and flash sintering of zirconium nitride powder

Suprabha Das et al.

Summary: This study successfully synthesized ZrN powder via a urea route and sintered it into near fully dense single-phase ceramics using a flash sintering setup. The effects of processing parameters on the synthesis method were investigated.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Ceramics

Mechanical properties of cold sintered ZnO investigated by nanoindentation and micro-pillar testing

Khushnuda Nur et al.

Summary: The mechanical properties of cold sintered and conventionally sintered ZnO samples were compared using nanoindentation and micro-pillar testing. It was found that cold sintered samples had higher hardness but lower elastic modulus and compressive stress. Transmission electron microscopy investigations confirmed the distinctive nature of grain boundary regions in cold sintered samples that influenced their deformation behavior.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Electrical resistance flash sintering of tungsten carbide

Isacco Mazo et al.

Summary: This study explored the ultrafast sintering of binderless tungsten carbide using electric/pressure assisted sintering, achieving high density in a few seconds by controlling the combination of voltage and pressure. Longer sintering time after flash sintering only slightly improved density, despite significant energetic consumption.

MATERIALS & DESIGN (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Ultra-fast high-temperature sintering of strontium titanate

Tarini Prasad Mishra et al.

Summary: This paper introduces the characteristics of Ultrafast High-temperature Sintering (UHS) technology and its application in the densification of strontium titanate samples. Experimental and simulation results show that UHS can achieve extremely high heating rates, rapid densification, and the addition of iron can control grain growth and achieve uniform densification and grain growth. Electrical conductivity tests indicate that UHS sintered samples can fully exhibit the functional properties of strontium titanate.

ACTA MATERIALIA (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Carbon free ultra-fast high temperature sintering of translucent zirconia

Jinghua Wu et al.

Summary: In this study, a novel UHS configuration based on a tungsten heater energized by a Spark Plasma Sintering machine (UH-SPS) was developed. This approach significantly reduced the firing time and maintained high transmittance, and it could be applied to other ceramics degraded by carbon contamination.

SCRIPTA MATERIALIA (2022)

Add to Collection

Editorial Material Materials Science, Ceramics

Ultrafast high-temperature sintering offers rapid, pressureless production of high-quality glasses

[Anonymous]

AMERICAN CERAMIC SOCIETY BULLETIN (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Rapid thermal sintering of screen-printed LiCoO2 films

Walter Sebastian Scheld et al.

Summary: A rapid photonic sintering process was used to obtain compact films of cathode active material of lithium batteries. The films showed homogeneous densification and structural consistency, and exhibited good electrochemical activity.

THIN SOLID FILMS (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Upscaling Ultrafast High-Temperature Sintering (UHS) to consolidate large-sized and complex-shaped ceramics

Fei Zuo et al.

Summary: This study proposes a novel Ultrafast High-temperature Sintering (UHS) configuration using graphite powder medium, which allows for the production of larger and complex-shaped ceramic products with fast sintering rate and fine tuning of microstructures.

SCRIPTA MATERIALIA (2022)

Add to Collection

Article Materials Science, Ceramics

Touch-free flash sintering with magnetic induction within a reactor activated by the usual flash method

Syed I. A. Jalali et al.

Summary: This study describes a new system for flash sintering, where a green sample is sintered quickly using an energy transfer mechanism between the reactor walls and the sample through a magnetic field. The experiments show that the reactor walls, in a constant state of flash, generate a concentrated plasma field that helps transfer energy to the green sample. The method is capable of achieving high-density and uniform nanoscale sintering in just a few seconds.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Ceramics

Microstructure and conductivity of blacklight-sintered TiO2, YSZ, and Li0.33La0.57TiO3

Lukas Porz et al.

Summary: Blacklight sintering technology enables rapid densification of ceramics with precise process control and excellent material quality.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2022)

Add to Collection

Article Chemistry, Physical

Rapid thermal processing of garnet-based composite cathodes

Walter Sebastian Scheld et al.

Summary: Rapid thermal annealing techniques are promising for processing ceramic materials, especially those containing elements with high vapor pressure. In this study, the sintering method RTP was used to fabricate composite ceramic cathodes of LLZO and LCO, effectively mitigating secondary phase formation between the two materials.

JOURNAL OF POWER SOURCES (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Pressureless flash sintering of α-SiC: Electrical characteristics and densification

Andrew Gibson et al.

Summary: The application of an electric field over a ceramic powder compact at elevated temperatures can achieve flash sintering in a shorter time compared to conventional sintering, without the need for external pressure. By adding specific sintering aids, high-density sintering can be achieved at lower temperatures.

ACTA MATERIALIA (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Blacklight sintering of ceramics

Lukas Porz et al.

Summary: This study achieved ultrafast heating of ceramics using intense blue and UV light, enabling sintering within seconds with high efficiency. This technology has broad application prospects and can be widely applied in energy storage and conversion, electronic, and structural applications.

MATERIALS HORIZONS (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Rapid Pressureless Sintering of Glasses

Zhiwei Lin et al.

Summary: This study reports an ultrafast high-temperature sintering (UHS) technique for the rapid fabrication of high-quality silica glass. Using UHS, silica precursors can be densified within seconds, resulting in sintered glasses with high relative densities and high visible transmittances. The UHS technique can also be extended to sinter other functional glasses and transparent ceramics.

SMALL (2022)

Add to Collection

Article Materials Science, Ceramics

Ultra-fast, selective, non-melting, laser sintering of alumina with anisotropic and size-suppressed grains

Xiao Geng et al.

Summary: This paper reports an ultra-fast sintering phenomenon of alumina achieved through scanning laser irradiation. The study found that alumina can be sintered to high density in a short time using laser scanning, with a different microstructure compared to furnace-sintered alumina. The grain size and relative density of laser-sintered alumina vary from the center to the edge of the laser beam, and the sintering mechanism is affected by the laser scanning speed.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Promoting microstructural homogeneity during flash sintering of ceramics through thermal management

Gareth M. Jones et al.

Summary: Flash sintering is a promising novel ceramic sintering technology that offers potential benefits in reducing firing time and furnace temperature, but challenges remain in scaling up to industrial manufacturing levels due to difficulties in managing heat generation and microstructural homogeneity.

MRS BULLETIN (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Electric-field-assisted processing of ceramics: Nonthermal effects and related mechanisms

Olivier Guillon et al.

Summary: Field-assisted processing methods, such as spark plasma sintering and flash sintering, expand the toolbox of ceramic engineering. Electric fields can induce nonthermal effects, including modifying defect formation and generating new phases. The interplay of ion transport and electrical conductivity is crucial for understanding effects caused by electric fields.

MRS BULLETIN (2021)

Add to Collection

Article Materials Science, Ceramics

Ultrafast high-temperature sintering (UHS) of fine grained α-Al2O3

Milad Kermani et al.

Summary: The research introduces a method of Ultrafast High-temperature Sintering (UHS) for producing fully dense and fine-grain alpha-Al2O3 samples. By utilizing a multi-step computer-controlled current profile, highly dense samples with an average grain size of 0.77 μm can be achieved in just a few tens of seconds.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Ceramics

Ultrafast high-temperature sintering of silicon nitride: A comparison with the state-of-the-art techniques

Rui-Xin Luo et al.

Summary: Ultrafast High-temperature Sintering (UHS) has been successfully applied to fabricate silicon nitride (Si3N4) bulks in a short period of time, achieving high density and promoting the evolution of the liquid phase sintering system towards a nonequilibrium state.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Thermally-insulated ultra-fast high temperature sintering (UHS) of zirconia: A master sintering curve analysis

Jian Dong et al.

Summary: The thermally-insulated Ultra-fast High temperature Sintering (UHS) technology utilizes a fiberboard insulator to reduce energy consumption by 40% compared to the reference set-up. With an ultrafast heating rate, dense and fine-grained microstructures are achieved within 60 seconds.

SCRIPTA MATERIALIA (2021)

Add to Collection

Article Multidisciplinary Sciences

Millisecond photonic sintering of iron oxide doped alumina ceramic coatings

Evgeniia Gilshtein et al.

Summary: In this study, alumina particles were sintered using millisecond flash lamp irradiation with extreme heating rates. The low visible light absorption of alumina was resolved by adding colored alpha -Fe2O3 nanoparticles, which initiated grain growth during sintering. This photonic sintering approach may be extended to other refractory ceramics with low absorption in the visible light range.

SCIENTIFIC REPORTS (2021)

Add to Collection

Article Materials Science, Ceramics

Flash sintering feasibility study and localized densification in boron carbide

Andrew Rosenberger et al.

Summary: The feasibility of flash sintering boron carbide was investigated by applying DC electric field across different electrodes, field strengths, and thermal profiles. Flash behavior was observed at low furnace temperatures with field strengths of 68-278 V/cm, but only a small channel of the specimen was densified due to hot spot effects. The scalable densification of B4C at low furnace temperatures with flash sintering is theorized to be possible by applying a higher current density through power supply or specimen modifications.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Ceramics

Development of a processing map for safe flash sintering of gadolinium-doped ceria

Tarini Prasad Mishra et al.

Summary: Flash sintering is a rapid sintering method suitable for oxides and complex ceramics. Electrical parameters, such as electric field and electric current, influence the onset temperature and densification of flash sintering. Developing a processing map, exemplified by gadolinium-doped ceria, can guide flash sintering in different material systems.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Ceramics

Modelling of elimination of strength-limiting defects by pressure-assisted sintering at low stress levels

Fumihiro Wakai et al.

Summary: The study demonstrates that large ellipsoidal voids can be eliminated by pressure-assisted sintering, and mechanical stress helps promote the rate of densification.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Ceramics

Li7La3Zr2O12 solid electrolyte sintered by the ultrafast high-temperature method

Martin Ihrig et al.

Summary: All-solid-state Li batteries with garnet LLZO as solid electrolyte show stability against Li metal, but challenges exist in integrating it due to high temperature and long dwell time for sintering. Advanced sintering techniques like Ultrafast High-temperature Sintering can significantly increase sintering rates, but demixing at grain boundaries may occur during sintering in vacuum and Ar atmosphere.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Low-Thermal-Budget Photonic Sintering of Hybrid Pastes Containing Submicron/Nano CuO/Cu2O Particles

Po-Hsiang Chiu et al.

Summary: Copper oxide particles were used to form conductive circuits through photonic sintering, resulting in improved electrical conductivity without damaging the substrate. The addition of Cu2O and copper formate was found to decrease the electrical resistivity of the reduced copper further.

NANOMATERIALS (2021)

Add to Collection

Article Materials Science, Ceramics

Element-specific displacements in defect-enriched TiO2: Indication of a flash sintering mechanism

Matte Jongmanns et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Ceramics

A theoretical analysis of cold sintering

Mattia Biesuz et al.

ADVANCES IN APPLIED CERAMICS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of AC field on uniaxial viscosity and sintering stress of ceria

Chen Cao et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Current-rate flash sintering of gadolinium doped ceria: Microstructure and Defect generation

Tarini Prasad Mishra et al.

ACTA MATERIALIA (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Application of Electric Current-Assisted Sintering Techniques for the Processing of Advanced Materials

Martin Bram et al.

ADVANCED ENGINEERING MATERIALS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Contactless flash sintering based on cold plasma

Jian Dong et al.

SCRIPTA MATERIALIA (2020)

Add to Collection

Article Multidisciplinary Sciences

A general method to synthesize and sinter bulk ceramics in seconds

Chengwei Wang et al.

SCIENCE (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Electronic conductivity in gadolinium doped ceria under direct current as a trigger for flash sintering

Tarini Prasad Mishra et al.

SCRIPTA MATERIALIA (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Reactive flash sintering of the entropy-stabilized oxide Mg0.2Ni0.2Co0.2Cu0.2Zn0.2O

Bola Yoon et al.

SCRIPTA MATERIALIA (2020)

Add to Collection

Article Materials Science, Ceramics

Sintering of a sodium-based NASICON electrolyte: A comparative study between cold, field assisted and conventional sintering methods

Joao Gustavo Pereira da Silva et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Add to Collection

Article Nanoscience & Nanotechnology

On the kinetics of liquid-assisted densification during flash sintering of ceramic nanoparticles

Rachman Chaim

SCRIPTA MATERIALIA (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Unveiling the mechanisms of cold sintering of ZnO at 250 degrees C by varying applied stress and characterizing grain boundaries by Kelvin Probe Force Microscopy

J. Gonzalez-Julian et al.

ACTA MATERIALIA (2018)

Add to Collection

Article Materials Science, Ceramics

Intergranular amorphous films formed by DC electric field in pure zirconia

Nobuhiro Morisaki et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2018)

Add to Collection

Article Materials Science, Ceramics

Selective laser sintering of porcelain

A. Danezan et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2018)

Add to Collection

Article Chemistry, Physical

Phase-pure BiFeO3 produced by reaction flash-sintering of Bi2O3 and Fe2O3

Eva Gil-Gonzalez et al.

JOURNAL OF MATERIALS CHEMISTRY A (2018)

Add to Collection

Review Materials Science, Ceramics

High-performance ceramic parts with complex shape prepared by selective laser sintering: a review

An-Nan Chen et al.

ADVANCES IN APPLIED CERAMICS (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Printed highly conductive Cu films with strong adhesion enabled by low-energy photonic sintering on low-Tg flexible plastic substrate

Xinzhou Wu et al.

NANOTECHNOLOGY (2017)

Add to Collection

Article Materials Science, Ceramics

Current understanding and future research directions at the onset of the next century of sintering science and technology

Rajendra K. Bordia et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

Ultra-fast firing: Effect of heating rate on sintering of 3YSZ, with and without an electric field

W. Ji et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2017)

Add to Collection

Article Engineering, Chemical

Spark plasma sintering and complex shapes: The deformed interfaces approach

Charles Maniere et al.

POWDER TECHNOLOGY (2017)

Add to Collection

Review Engineering, Mechanical

Direct selective laser sintering and melting of ceramics: a review

Swee Leong Sing et al.

RAPID PROTOTYPING JOURNAL (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Probing the densification mechanisms during flash sintering of ZnO

Yuanyao Zhang et al.

ACTA MATERIALIA (2017)

Add to Collection

Article Chemistry, Multidisciplinary

Protocol for Ultralow-Temperature Ceramic Sintering: An Integration of Nanotechnology and the Cold Sintering Process

Hanzheng Guo et al.

ACS NANO (2016)

Add to Collection

Article Chemistry, Multidisciplinary

Cold Sintering Process of Composites: Bridging the Processing Temperature Gap of Ceramic and Polymer Materials

Jing Guo et al.

ADVANCED FUNCTIONAL MATERIALS (2016)

Add to Collection

Article Chemistry, Multidisciplinary

Cold Sintering: A Paradigm Shift for Processing and Integration of Ceramics

Jing Guo et al.

ANGEWANDTE CHEMIE-INTERNATIONAL EDITION (2016)

Add to Collection

Article Materials Science, Ceramics

Cold Sintering Process: A Novel Technique for Low-Temperature Ceramic Processing of Ferroelectrics

Hanzheng Guo et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2016)

Add to Collection

Article Materials Science, Ceramics

Analysis of the Power Density at the Onset of Flash Sintering

Rishi Raj

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2016)

Add to Collection

Article Materials Science, Ceramics

FAST/SPS sintering of nanocrystalline zinc oxide-Part I: Enhanced densification and formation of hydrogen-related defects in presence of adsorbed water

Benjamin Dargatz et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2016)

Add to Collection

Article Engineering, Mechanical

Shaping ceramics through indirect selective laser sintering

Jan Patrick Deckers et al.

RAPID PROTOTYPING JOURNAL (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Inkjet printing and photonic sintering of silver and copper oxide nanoparticles for ultra-low-cost conductive patterns

Andreas Albrecht et al.

JOURNAL OF MATERIALS CHEMISTRY C (2016)

Add to Collection

Article Multidisciplinary Sciences

All-photonic drying and sintering process via flash white light combined with deep-UV and near-infrared irradiation for highly conductive copper nano-ink

Hyun-Jun Hwang et al.

SCIENTIFIC REPORTS (2016)

Add to Collection

Article Multidisciplinary Sciences

Ultrafast-Contactless Flash Sintering using Plasma Electrodes

Theo Saunders et al.

SCIENTIFIC REPORTS (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Growth of single crystalline seeds into polycrystalline strontium titanate: Anisotropy of the mobility, intrinsic drag effects and kinetic shape of grain boundaries

Wolfgang Rheinheimer et al.

ACTA MATERIALIA (2015)

Add to Collection

Article Materials Science, Ceramics

Electroluminescence and the measurement of temperature during Stage III of flash sintering experiments

Kalvis Terauds et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2015)

Add to Collection

Article Materials Science, Ceramics

Electrical characteristics of flash sintering: thermal runaway of Joule heating

R. I. Todd et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2015)

Add to Collection

Review Materials Science, Multidisciplinary

Field-Assisted Sintering Technology/Spark Plasma Sintering: Mechanisms, Materials, and Technology Developments

Olivier Guillon et al.

ADVANCED ENGINEERING MATERIALS (2014)

Add to Collection

Article Materials Science, Ceramics

Flash Spark Plasma Sintering (FSPS) of Pure ZrB2

Salvatore Grasso et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2014)

Add to Collection

Article Materials Science, Ceramics

Influence of the Field and the Current Limit on Flash Sintering at Isothermal Furnace Temperatures

John S. C. Francis et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2013)

Add to Collection

Article Materials Science, Ceramics

Preliminary investigation of flash sintering of SiC

E. Zapata-Solvas et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2013)

Add to Collection

Article Materials Science, Ceramics

An experimental setup for shrinkage evaluation during electric field-assisted flash sintering: Application to yttria-stabilized zirconia

R. Muccillo et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2013)

Add to Collection

Review Materials Science, Multidisciplinary

Laser additive manufacturing of metallic components: materials, processes and mechanisms

D. D. Gu et al.

INTERNATIONAL MATERIALS REVIEWS (2012)

Add to Collection

Article Materials Science, Ceramics

Effect of Electrical Field/Current on Sintering of Fully Stabilized Zirconia

Raschid Baraki et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2012)

Add to Collection

Article Materials Science, Ceramics

Low Temperature Sintering of Nanocrystalline Zinc Oxide: Effect of Heating Rate Achieved by Field Assisted Sintering/Spark Plasma Sintering

Sebastian Schwarz et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2012)

Add to Collection

Article Materials Science, Ceramics

Joule heating during flash-sintering

Rishi Raj

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2012)

Add to Collection

Article Chemistry, Multidisciplinary

Origin of the Ultra-nonlinear Switching Kinetics in Oxide-Based Resistive Switches

Stephan Menzel et al.

ADVANCED FUNCTIONAL MATERIALS (2011)

Add to Collection

Article Materials Science, Ceramics

Building a Sintering Front through Fast Firing

Daniel E. Garcia et al.

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2011)

Add to Collection

Article Materials Science, Ceramics

Flash Sintering of Nanograin Zirconia in <5 s at 850°C

Marco Cologna et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2010)

Add to Collection

Article Materials Science, Ceramics

Chemical solution-deposited BaTiO3 thin films on Ni foils:: Microstructure and interfaces

Tanawadee Dechakupt et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2008)

Add to Collection

Article Chemistry, Physical

Ceramic components manufacturing by selective laser sintering

Ph. Bertrand et al.

APPLIED SURFACE SCIENCE (2007)

Add to Collection

Article Materials Science, Multidisciplinary

Carbonate binders by cold sintering of calcium carbonate

Premalatha De Silva et al.

JOURNAL OF MATERIALS SCIENCE (2007)

Add to Collection

Article Materials Science, Multidisciplinary

The synthesis of lead-free ferroelectric Bi0.5Na0.5TiO3-Bi0.5K0.5TiO3 thin films by sol-gel method

T. Yu et al.

MATERIALS LETTERS (2007)

Add to Collection

Article Geochemistry & Geophysics

Microstructural evolution and grain boundary structure during static recrystallization in synthetic polycrystals of Sodium Chloride containing saturated brine

O Schenk et al.

CONTRIBUTIONS TO MINERALOGY AND PETROLOGY (2004)

Add to Collection

Article Materials Science, Ceramics

Properties of nanocrystalline ferroelectric PZT ceramics

Z Surowiak et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2001)

Add to Collection

© Peeref 2019-2024. All rights reserved.