☆ 4.6 Article

Hot Deformation Analysis and Microstructure Evolution of a Novel Al-Cu-Li Alloy by Isothermal Compression

ADVANCED ENGINEERING MATERIALS (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Effects of Dynamic Precipitation and Processing Parameters on Dynamic Recrystallization Behavior of 2195 Al-Cu-Li Alloy during Hot Compression

You-jie Guo et al.

Summary: The study on the effects of dynamic precipitation and processing parameters on the dynamic recrystallization behavior of 2195 Al-Cu-Li alloy revealed that the Zener-Hollomon parameter plays a crucial role in the softening process while temperature-induced phase changes can shift softening mechanisms. As Z value decreases, the recrystallization mechanism shifts from discontinuous to continuous, with temperature and phase composition influencing the transition.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Deformation microstructure and thermomechanical processing maps of homogenized AA2070 aluminum alloy

Jiashi Miao et al.

Summary: The hot deformation behavior of homogenized AA2070 Al-Li-Cu alloy was studied, and it was found that dynamic precipitation of T-1 phase causes back stress at temperatures below 400°C, while intermetallic phases gradually dissolve at temperatures above 400°C, leading to dominant dynamic recrystallization as the softening mechanism.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Chemistry, Physical

T1 precipitate bands and particle stimulated nucleation in 2195 Al-Cu-Li alloy during hot deformation

Ding-ding Lu et al.

Summary: This paper investigates the dynamic precipitation and recrystallization behavior of aluminum alloys at middle temperature and appropriate strain rates. The results show that these behaviors significantly improve the mechanical properties of the alloys. The study provides valuable insights into the optimization of material structures.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Chemistry, Physical

Modeling Dynamic Recrystallization Behavior in a Novel HIPed P/M Superalloy during High-Temperature Deformation

Qiu-Mei Yang et al.

Summary: The features and evolution of microstructure of a new HIPed P/M superalloy are investigated through hot-compression tests. The study reveals the significant influence of deformation conditions on dynamic recrystallization (DRX) features and grain-growth behavior.

MATERIALS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Dynamic microstructural evolution of Al-Cu-Li alloys during hot deformation

Ya Tang et al.

Summary: In this study, the evolution of deformation microstructures and multiscale phases in Al-Cu-Li alloy was investigated under different temperatures and strain rates. The results showed that the compress temperature has an impact on the characteristic and dynamic deformation behaviors of secondary phases. Proper strain rates can promote the formation and growth of multistage banded T-1 phase.

MATERIALS CHARACTERIZATION (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Hot deformation behavior and microstructure evolution of the spray deposited and secondary hot extruded 2195 Al-Li alloy

Guojing Yang et al.

Summary: This study investigates the influence of hot deformation parameters on the microstructure evolution and deformation behavior of the extruded 2195 Al-Li alloy. The optimized hot deformation conditions lead to continuous dynamic recrystallization and microstructure refinement. The presence of large second phases and liquid-like grain boundaries in the extruded plate results in a lower deformation activation energy.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Dynamic microstructural evolution of Al-Cu-Li alloys during hot deformation

Ya Tang et al.

Summary: The study reveals that compression temperature significantly influences the characteristic and dynamic behavior of secondary phases in Al-Cu-Li alloy during hot deformation. Proper strain rates can accelerate the formation and growth of T-1 phase, but at higher temperatures, T-1 phase may completely dissolve into the matrix.

MATERIALS CHARACTERIZATION (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Dynamic Softening Mechanism and an Improved Unified Constitutive Model for an Al-Cu-Mn-Fe-Zr Alloy during Warm Deformation

Jun-Quan Wang et al.

Summary: The deformation behavior of an Al-Cu-Mn-Fe-Zr alloy is influenced by temperature and strain rate, with the dominant mechanism being dynamic recovery to balance work hardening. Low strain rates consume more dislocations, making it difficult to trigger dynamic recrystallization, while high strain rates promote the process of dynamic recrystallization.

ADVANCED ENGINEERING MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Kinetic model for describing continuous and discontinuous dynamic recrystallization behaviors of 2195 aluminum alloy during hot deformation

Jingjing Zhang et al.

Summary: Dynamic recrystallization behavior of 2195 aluminum alloy was studied through hot compression experiments, revealing both discontinuous and continuous dynamic recrystallization occurring in the alloy within the temperature range of 300-520 degrees Celsius and strain rates of 0.01-10 s(-1). The dominant DRX mechanism transitioned from DDRX to CDRX when the strain exceeded 1.2, with the number of CDRX grains increasing at higher temperatures or lower strain rates.

MATERIALS CHARACTERIZATION (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Dynamic recrystallization mechanisms of 2195 aluminum alloy during medium/high temperature compression deformation

Jingjing Zhang et al.

Summary: The study found that the 2195 aluminum alloy softens mainly through DDRX at medium temperatures and through CDRX at high temperatures. Additionally, the CDRX process involves multiple subgrain-forming mechanisms.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Chemistry, Physical

Effects of coarse Al2CuLi phase on the hot deformation behavior of Al-Li alloy

Xiao-Ya Wang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure and hot deformation behavior of a new aluminum-lithium-copper based AA2070 alloy

Jiashi Miao et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Progress in characterization methods for thermoplastic deforming constitutive models of Al-Li alloys: a review

Peng Zhang et al.

JOURNAL OF MATERIALS SCIENCE (2020)

Add to Collection

Article Engineering, Manufacturing

Constitutive modeling and microstructure characterization of 2196 Al-Li alloy in various hot deformation conditions

Xiaoxue Chen et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure evolution and processing map of Al-Cu-Li-Mg-Ag alloy

Qingbo Yang et al.

MATERIALS CHEMISTRY AND PHYSICS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Hot deformation characterization of as-homogenized Al-Cu-Li X2A66 alloy through processing maps and microstructural evolution

Liwei Zhong et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

Add to Collection

Review Multidisciplinary Sciences

Strengthening mechanisms, deformation behavior, and anisotropic mechanical properties of Al-Li alloys: A review

Ali Abd El-Aty et al.

JOURNAL OF ADVANCED RESEARCH (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Plastic flow behavior and microstructure characteristics of light-weight 2060 Al-Li alloy

Xingwei Zheng et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Chemistry, Physical

Dynamic restoration mechanism and physically based constitutive model of 2050 Al-Li alloy during hot compression

Ruihua Zhu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

Add to Collection

Article Chemistry, Physical

Hot deformation behavior of 2060 alloy

Ling Ou et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

Add to Collection

Review Materials Science, Multidisciplinary

Recent developments in advanced aircraft aluminium alloys

Tolga Dursun et al.

MATERIALS & DESIGN (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Flow behavior and processing maps of 2099 alloy

F. Zhang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Chemistry, Physical

Hot deformation and processing map of a typical Al-Zn-Mg-Cu alloy

Y. C. Lin et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2013)

Add to Collection

Article Nanoscience & Nanotechnology

High temperature deformation behavior and optimal hot processing parameters of Al-Si eutectic alloy

H. E. Hu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)

Add to Collection

Article Nanoscience & Nanotechnology

Modeling constitutive relationship of Ti17 titanium alloy with lamellar starting microstructure

Xiong Ma et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)

Add to Collection

Article Nanoscience & Nanotechnology

A phenomenological constitutive model for high temperature flow stress prediction of Al-Cu-Mg alloy

Y. C. Lin et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)

Add to Collection

Article Materials Science, Multidisciplinary

The Evolution of Al-Li Base Products for Aerospace and Space Applications

Roberto J. Rioja et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2012)

Add to Collection

Article Materials Science, Multidisciplinary

Hot deformation and processing maps of extruded ZE41A magnesium alloy

S. Anbuselvan et al.

MATERIALS & DESIGN (2010)

Add to Collection

Article Nanoscience & Nanotechnology

Hot deformation behaviour of as-cast Mg-2Zn-1Mn alloy in compression: a study with processing map

O Sivakesavam et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)

Add to Collection

Article Nanoscience & Nanotechnology

Constitutive analysis in hot working

HJ McQueen et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2002)

Add to Collection

© Peeref 2019-2024. All rights reserved.