☆ 4.8 Article

A novel droplet plus arc additive manufacturing for aluminum alloy: Method, microstructure and mechanical properties

ADDITIVE MANUFACTURING (2023)

Related references

Note: Only part of the references are listed.

Article Optics

Mechanism investigation for the influence of laser power on droplet transfer behaviors in laser-MIG hybrid welding

Fuyun Liu et al.

Summary: This study investigates the influence of laser power on droplet transfer in laser-MIG hybrid welding. The results indicate that increasing laser power can improve the transfer frequency, but it decreases once the power exceeds a critical value. Considering factors such as laser source characteristics, materials, laser focusing distance, and laser-arc distance, these findings provide guidance for optimizing welding processes, improving weld quality, and preventing spatters.

OPTICS AND LASER TECHNOLOGY (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Grain refinement and property improvements of Al-Zn-Mg-Cu alloy by heterogeneous particle addition during wire and arc additive manufacturing

Tao Yuan et al.

Summary: This research focused on grain refining of Al-Zn-Mg-Cu alloys by adding TiN particles during wire and arc additive manufacturing (WAAM). The addition of TiN particles led to equiaxed grains, reduced grain size, and improved mechanical properties of the alloy.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Engineering, Industrial

Effect of Hot Isostatic Pressing and heat treatments on porosity of Wire Arc Additive Manufactured Al 2319

N. Mclean et al.

Summary: By quantitatively studying the extent of pore regrowth during post-HIP solution treatment and ageing of Al 2319 produced by Wire Arc Additive Manufacturing (WAAM), it was found that large closed pores mostly remained closed during subsequent heat treatment, but the frequency of fine gas porosity increased almost three-fold. However, the overall porosity distribution after post-HIP heat treatment was still up to 95% lower than in the original as-built condition, indicating that HIP + heat treatments are still a viable pathway for defect reduction in industrial products.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of high-melting particle implantation on microstructure of Al alloy thin-wall components fabricated by droplet plus arc additive manufacturing

Pengfei He et al.

Summary: In this paper, a novel droplet + arc additive manufacturing technique is proposed for fabricating particle-reinforced Al matrix composites parts. Experimental results show that the interface pore defects are affected by the wettability between particle and liquid Al matrix. Additionally, the transition of grain size can be achieved by particle implantation.

MATERIALS LETTERS (2022)

Add to Collection

Article Engineering, Industrial

Metal transfer modes for Wire Arc Additive Manufacturing Al-Mg alloys: Influence of heat input in microstructure and porosity

E. Aldalur et al.

Summary: WAAM technology is used to manufacture medium-to-large metallic parts using aluminum alloys, with aluminum alloy 5356 being analyzed in this study. Three working modes for aluminum alloys are compared, with pulsed-AC mode showing significantly reduced porosity levels and being a very attractive mode for this aluminum alloy.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection

Article Engineering, Industrial

Characteristics of bypass coupling twin-wire indirect arc welding with high-speed welding mode

Dongting Wu et al.

Summary: The study investigated the welding characteristics of bypass coupling twin-wire indirect arc welding (BC-TWIAW) with high-speed welding mode. The alternating burning of direct and indirect arcs could significantly reduce the heat input into the workpiece. Different droplet transfer patterns were observed depending on the feeding speed of the cathode wire.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection

Review Materials Science, Multidisciplinary

Enhancing the properties of aluminum alloys fabricated using wire plus arc additive manufacturing technique-A review

M. M. Tawfik et al.

Summary: Recent advancements in wire thorn arc additive manufacturing (WAAM) of aluminum components offer unique opportunities for enhancing their properties. Studies have focused on controlling manufacturing parameters, wire properties, arc mode, and post-process treatment to regulate microstructure and mechanical characteristics of fabricated aluminum parts. The paper reviews various attempts to enhance the mechanical properties of aluminum components fabricated with WAAM, as well as challenges faced in applying WAAM to aluminum alloys. The main goal is to gain a detailed understanding of the mechanical characteristics of deposited aluminum components under different conditions.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Chemistry, Physical

Hot deformation induced microstructural evolution in local-heterogeneous wire plus arc additive manufactured 2219 Al alloy

Yinghui Zhou et al.

Summary: This study investigated the hot deformation behavior and microstructural evolution of a wire + arc additive manufactured (WAAMed) 2219 Al alloy. The local-heterogeneous microstructure showed an alternated distribution of equiaxed and columnar grains, with 0' phase precipitating near grain boundaries. Analysis revealed a higher stress resistance during hot deformation compared to traditional 2219 Al alloys, with dynamic recrystallization impacting grain boundaries and hardness.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Laser Power on the Microstructure and Mechanical Properties of 2319-Al Fabricated by Wire-Based Additive Manufacturing

Zhaodong Zhang et al.

Summary: The use of low-power pulsed laser-induced MIG arc additive manufacturing to fabricate 2319 Al alloy samples results in improved forming quality and enhanced mechanical properties with increased laser power. The improved mechanical properties are attributed to grain refinement and microstructure improvement.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical properties and precipitation behavior of the heat-treated wire plus arc additively manufactured 2219 aluminum alloy

Yinghui Zhou et al.

Summary: The dense 2219 Al alloy was successfully fabricated using Wire + Arc additive manufacturing technology, followed by solution and aging (T6) heat treatment to improve performance. The precipitation strengthening of the theta '' phase improves with increasing solution temperature, enhancing the mechanical properties of the material.

MATERIALS CHARACTERIZATION (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of travel speed on microstructure and mechanical properties of wire plus arc additively manufactured 2219 aluminum alloy

Yinghui Zhou et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

Add to Collection

Article Multidisciplinary Sciences

Grain structure control during metal 3D printing by high-intensity ultrasound

C. J. Todaro et al.

NATURE COMMUNICATIONS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure, defects, and mechanical properties of wire plus arc additively manufactured Al-Cu4.3-Mg1.5 alloy

Jianglong Gu et al.

MATERIALS & DESIGN (2020)

Add to Collection

Article Engineering, Manufacturing

External filler wire based GMA-AM process of 2219 aluminum alloy

Guangchao Liu et al.

MATERIALS AND MANUFACTURING PROCESSES (2020)

Add to Collection

Article Engineering, Manufacturing

Effect of post-deposition heat treatment on laser-TIG hybrid additive manufactured Al-Cu alloy

Dehua Liu et al.

VIRTUAL AND PHYSICAL PROTOTYPING (2020)

Add to Collection

Review Materials Science, Multidisciplinary

A review of selective laser melting of aluminum alloys: Processing, microstructure, property and developing trends

Jinliang Zhang et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

Add to Collection

Review Chemistry, Physical

Current Status and Perspectives on Wire and Arc Additive Manufacturing (WAAM)

Tiago A. Rodrigues et al.

MATERIALS (2019)

Add to Collection

Article Engineering, Manufacturing

Microstructure and mechanical properties of wire plus arc additively manufactured 2024 aluminum alloy components: As-deposited and post heat-treated

Zewu Qi et al.

JOURNAL OF MANUFACTURING PROCESSES (2019)

Add to Collection

Article Engineering, Manufacturing

Droplet transfer behavior in bypass-coupled wire arc additive manufacturing

Jiankang Huang et al.

Journal of Manufacturing Processes (2019)

Add to Collection

Article Chemistry, Physical

Microstructure, residual stress and tensile properties control of wire-arc additive manufactured 2319 aluminum alloy with laser shock peening

Rujian Sun et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Article Engineering, Industrial

Influence of pulsed arc on the metal droplet deposited by projected transfer mode in wire-arc additive manufacturing

Luo Yi et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)

Add to Collection

Article Engineering, Industrial

Design and cracking susceptibility of additively manufactured Al-Cu-Mg alloys with tandem wires and pulsed arc

Jianglong Gu et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Friction stir welding of high-strength aerospace aluminum alloy and application in rocket tank manufacturing

Guoqing Wang et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2018)

Add to Collection

Article Computer Science, Interdisciplinary Applications

Manufacture of complex thin-walled metallic objects using weld-deposition based additive manufacturing

Jayaprakash Sharma Panchagnula et al.

ROBOTICS AND COMPUTER-INTEGRATED MANUFACTURING (2018)

Add to Collection

Review Engineering, Manufacturing

A review of the wire arc additive manufacturing of metals: properties, defects and quality improvement

Bintao Wu et al.

JOURNAL OF MANUFACTURING PROCESSES (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical Properties and Fracture Behaviors of GTA-Additive Manufactured 2219-Al After an Especial Heat Treatment

J. Y. Bai et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2017)

Add to Collection

Article Multidisciplinary Sciences

3D printing of high-strength aluminium alloys

John H. Martin et al.

NATURE (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Additive manufacturing of metals

Dirk Herzog et al.

ACTA MATERIALIA (2016)

Add to Collection

Article Automation & Control Systems

Effects of thermal cycles on microstructure evolution of 2219-Al during GTA-additive manufacturing

J. Y. Bai et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)

Add to Collection

Article Nanoscience & Nanotechnology

The strengthening effect of inter-layer cold working and post-deposition heat treatment on the additively manufactured Al-6.3Cu alloy

Jianglong Gu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Wire plus Arc Additive Manufacturing

S. W. Williams et al.

MATERIALS SCIENCE AND TECHNOLOGY (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and mechanical property considerations in additive manufacturing of aluminum alloys

Y. Ding et al.

MRS BULLETIN (2016)

Add to Collection

Article Materials Science, Multidisciplinary

A criterion for cracking during solidification

Sindo Kou

ACTA MATERIALIA (2015)

Add to Collection

Article Nanoscience & Nanotechnology

Precipitation behavior of aluminum alloy 2139 fabricated using additive manufacturing

Craig Brice et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Add to Collection

Article Automation & Control Systems

Effect of arc mode in cold metal transfer process on porosity of additively manufactured Al-6.3% Cu alloy

Baoqiang Cong et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)

Add to Collection

Review Materials Science, Multidisciplinary

Recent developments in advanced aircraft aluminium alloys

Tolga Dursun et al.

MATERIALS & DESIGN (2014)

Add to Collection

© Peeref 2019-2024. All rights reserved.