☆ 4.7 Article

Mechanical and wear evolution of in situ synthesized Ti-Cu alloy matrix hybrid composite reinforced by low-cost activated carbon and silica fume waste ceramic for industrial applications

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Improved mechanical properties in titanium matrix composites reinforced with quasi-continuously networked graphene nanosheets and in-situ formed carbides

Q. Yan et al.

Summary: A quasi-networked reinforcement structure in titanium matrix composites was achieved by uniformly coating Ti-6Al-4V spherical powders with a graphene nanosheet layer, leading to higher tensile strength and good ductility compared to randomly dispersed graphene nanosheets and TiC. The study provided a method to fabricate titanium matrix composites with high strength and good ductility by forming a networked hybrid reinforcement structure.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

Add to Collection

Article Chemistry, Physical

Influence of Friction Stir Process on the Physical, Microstructural, Corrosive, and Electrical Properties of an Al-Mg Alloy Modified with Ti-B Additives

Essam B. Moustafa et al.

Summary: Two successive methods were used to improve the grain structure and properties of Al 5052 aluminum alloy: the addition of titanium and boron during casting, and single- and double-pass friction stir processing (FSP). The Ti-B modifiers significantly improved the mechanical and physical properties, with only a 3% increase in microhardness. Grain refinement had significant effects on thermal expansion and corrosion rate.

MATERIALS (2022)

Add to Collection

Article Chemistry, Physical

Effects of metastable θ′ precipitates on the strengthening, wear and electrical behaviors of Al 2519-SiC/fly ash hybrid nanocomposites synthesized by powder metallurgy technique

Smain Bezzina et al.

Summary: Hybrid Al-Cu-Si matrix nanocomposites with different proportions of SiC and fly ash were prepared using powder metallurgy technique to enhance the mechanical and elastic properties as well as wear resistance of Al-Cu-Mg matrix. The study also investigated the effect of aging time on the wear behavior, mechanical and electrical properties. The results showed that increasing the weight percentages of hybrid ceramics resulted in a weakening of the precipitation phase and a decrease in crystal and particle sizes. The prepared nanocomposites exhibited significant improvement in microhardness, Young's modulus, compressive strength, and reduced wear rate.

SILICON (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Tool wear, surface roughness, cutting temperature and chips morphology evaluation of Al/TiN coated carbide cutting tools in milling of Cu-B-CrC based ceramic matrix composites

Usame Ali Usca et al.

Summary: This study aims to investigate the machinability characteristics of Cu-B-CrC composites using Al/TiN coated carbide tools. The influence of machining parameters and the weight ratios of the powders used to fabricate the machined reinforced samples on output parameters was examined. The dominant effect of reinforcement ratio on machinability was found, showing that a 5% additive provides improved properties such as surface roughness, tool wear, and cutting temperature.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Polymer Science

A Study to Evaluate the Bioactivity Behavior and Electrical Properties of Hydroxyapatite/Ag2O-Borosilicate Glass Nanocomposites for Biomedical Applications

Asma M. Alturki et al.

Summary: The nanocomposites prepared by mixing different contents of borosilicate glass and carbonated hydroxyapatite exhibited unexpected results during sintering, with the increase in borosilicate glass content leading to partial decomposition of the hydroxyapatite and enhanced bioactivity behavior, as well as improvements in mechanical properties including hardness, strength, and moduli.

JOURNAL OF INORGANIC AND ORGANOMETALLIC POLYMERS AND MATERIALS (2022)

Add to Collection

Article Materials Science, Ceramics

Evaluation of the dynamic behavior, elastic properties, and in vitro bioactivity of some borophosphosilicate glasses for orthopedic applications

Waheed S. S. Abushanab et al.

Summary: This study used finite element modeling to predict the effects of increasing borate content on mechanical properties and dynamic behavior. The results showed that increasing borate content improved the deflect resistance of the glass samples by 39%, while shear stress and principle stress were not affected. Gradual increases in borate content also improved the bioactivity of the samples.

JOURNAL OF NON-CRYSTALLINE SOLIDS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Tribo-mechanical measurements and in vivo performance of zirconia-containing biphasic calcium phosphate material implanted in a rat model for bone replacement applications

Rasha A. Youness et al.

Summary: This study aimed to improve the performance of biphasic calcium phosphate (BCP) for bone replacement applications. By adding zirconia (ZrO2), the nanocomposites exhibited enhanced tribological and mechanical properties, with reduced particle sizes. The implanted nanocomposite also demonstrated excellent bioactivity.

MATERIALS CHEMISTRY AND PHYSICS (2022)

Add to Collection

Review Materials Science, Multidisciplinary

Processing and microstructure of Ti-Cu binary alloys: A comprehensive review

Mohammad Reza Akbarpour et al.

Summary: Titanium alloys are widely used in various industries, such as medical and dental, due to their excellent properties. The alloying of titanium with copper can enhance its mechanical performance, biocompatibility, corrosion resistance, and melting point. The microstructural properties of Ti-Cu alloys are sensitive to factors like intermetallic formation and growth, which depend on the amount of copper and the manufacturing techniques used. This study aims to investigate the effect of manufacturing paths on the microstructural properties of Ti-Cu alloys, discussing various fabrication procedures and addressing the challenges, opportunities, and future perspectives.

PROGRESS IN MATERIALS SCIENCE (2022)

Add to Collection

Article Chemistry, Physical

The Effect of Different Fly Ash and Vanadium Carbide Contents on the Various Properties of Hypereutectic Al-Si Alloys-Based Hybrid Nanocomposites

Waheed S. AbuShanab et al.

Summary: In this study, a hybrid nanocomposite Al-Si matrix was successfully fabricated using powder metallurgy method, resulting in strengthened matrix and improved mechanical properties. By adding varying weight percentages of VC and FA nanoparticles, the alloy particle sizes were reduced and wear/corrosion resistance was increased. The hybridized composites showed significantly enhanced mechanical performance and microstructure under sintering conditions.

SILICON (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation of machinability of Ti-B-SiCp reinforced Cu hybrid composites in dry turning

Serhat Sap et al.

Summary: Metal matrix composites (MMCs) are widely used due to their high specific strength, but their machinability presents challenges. The machinability of Cu composites reinforced with Ti-B-SiC powder particles at different ratios was studied, and the effects of cutting parameters on surface roughness, flank wear, and cutting temperature were investigated.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Improvement of the microstructure and mechanical properties by hybridizing the surface of AA7075 by hexagonal boron nitride with carbide particles using the FSP process

Essam B. Moustafa et al.

Summary: In this study, hybrid metal-matrix-surface composites (HMMSC) were fabricated using the friction stir process (FSP), with hexagonal boron nitride (HBN) as the main reinforcement for improving the tribological behavior of AA7075 aluminum alloy. Additional secondary reinforced particles, including silicon carbide (SiC), tantalum carbide (TaC), and niobium carbide (NbC) nanoparticles, were used to enhance resistance to deformation, chemical stability, and grain growth control. The hybridization process resulted in uniform distribution of the reinforcing particles and significant grain refinement. The hybrid composites exhibited improved mechanical properties and wear resistance compared to the base alloy.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Improved mechanical properties of Cu8Ni4Sn alloy as functionally graded composites with preserving its thermal and electrical properties

Essam B. Moustafa et al.

Summary: The main objective of this study was to improve the mechanical properties of a copper alloy without reducing its electrical and thermal conductivity. Five-layer functionally graded composites were prepared by adding Ti3AlC2 MAX phase to the copper alloy. The top layer showed significant improvement in mechanical properties while only slight reduction in thermal and electrical properties.

MATERIALS CHEMISTRY AND PHYSICS (2022)

Add to Collection

Article Materials Science, Ceramics

Fabrication of Al/Al2O3/ SiC/graphene hybrid nanocomposites from Al-dross by powder metallurgy: Sinterability, mechanical and electrical properties

Mohammed A. Taha et al.

Summary: In this study, sintered Al/Al2O3 hybrid composites reinforced with varying amounts of SiC and graphene were prepared using aluminum dross waste. The effects of reinforcement content and sintering temperature on the properties of the composites were investigated. The results showed improvements in physical, mechanical, and electrical properties with increasing SiC and graphene content as well as sintering temperature.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Ceramics

Evaluation of the electrical and dielectric behavior of the apatite layer formed on the surface of hydroxyapatite/hardystonite/copper oxide hybrid nanocomposites for bone repair applications

Rasha A. Youness et al.

Summary: The aim of this work was to prepare nanocomposites with good electrical and mechanical properties and acceptable bioactivity behavior for bone repair applications. The results showed that the prepared nanocomposites exhibited good densification behavior and improved mechanical properties, and positively enhanced fracture healing.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of C addition on microstructure and mechanical properties of laser micro-alloying Ti-Al-V-C titanium matrix composites

Fengying Zhang et al.

Summary: This research introduces a novel laser processing experiment called laser micro-alloying (LMA) to deposit Ti-Al-V-xC alloys and investigate the solid solution relationships between C, Al, and V in different matrices, as well as the effect of C on the in-situ precipitation behavior of TiC. The results show that the solid solubility of C decreases with increasing Al and V contents, and the addition of C enhances the precipitation of TiC in the Ti alloy matrix, resulting in increased hardness and strength.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Chemistry, Multidisciplinary

The effect of TaC and NbC hybrid and mono-nanoparticles on AA2024 nanocomposites: Microstructure, strengthening, and artificial aging

Essam B. Moustafa et al.

Summary: This study successfully incorporated the composite surface matrices and mononanoparticles into AA2024 using FSP, improving its mechanical properties and evaluating its microstructural and electrical properties.

NANOTECHNOLOGY REVIEWS (2022)

Add to Collection

Article Chemistry, Physical

Corrosion and tribocorrosion behaviour of Ti-B4C composites processed by conventional sintering and hot-pressing technique

L. Sousa et al.

Summary: The study found that Ti-B4C composites processed by different methods exhibit differences in corrosion resistance and tribocorrosion behavior. Additionally, the composites showed a tendency towards certain corrosion resistance characteristics in tribocorrosion tests.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Polymer Science

Synthesis, Structural and Biomedical Characterization of Hydroxyapatite/Borosilicate Bioactive Glass Nanocomposites

Dalia E. Abulyazied et al.

Summary: The study showed that incorporating borosilicate glass can enhance the bioactivity and antibacterial effect of carbonated hydroxyapatite, as well as the physical and mechanical properties of the resulting nanocomposites. The sample with the highest content of borosilicate glass exhibited the best performance in terms of bioactivity, antibacterial effect, physical, and mechanical properties.

JOURNAL OF INORGANIC AND ORGANOMETALLIC POLYMERS AND MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Evolution of the Microstructure and Mechanical Properties of a Ti35Nb2Sn Alloy Post-Processed by Hot Isostatic Pressing for Biomedical Applications

Joan Lario et al.

Summary: The influence of HIP post-processing on structural changes, porosity healing, and mechanical strength in powder metallurgy titanium alloys was investigated. Results showed that specific HIP processing conditions can significantly reduce porosity and retain the beta phase at room temperature.

METALS (2021)

Add to Collection

Article Chemistry, Physical

Microstructure, mechanical properties and antibacterial properties of the microwave sintered porous Ti-3Cu alloys

S. C. Tao et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Synthesis and structural properties characterization of titania/zirconia/calcium silicate nanocomposites for biomedical applications

Waheed S. AbuShanab et al.

APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2020)

Add to Collection

Article Materials Science, Ceramics

Ti-based composite materials with enhanced thermal and mechanical properties

Cristina Ileana Pascu et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation on corrosion behavior of Cu-TiO2 nanocomposite synthesized by the use of SHS method

Naseri Azari Golnaz et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical Behavior and Microstructure Evolution of a Ti-15Mo/TiB Titanium-Matrix Composite during Hot Deformation

Sergey Zherebtsov et al.

METALS (2019)

Add to Collection

Article Materials Science, Ceramics

Synthesis of TiC reinforced Ti matrix composites by spark plasma sintering and electric discharge sintering: A comparative assessment of microstructural and mechanical properties

W. H. Lee et al.

CERAMICS INTERNATIONAL (2019)

Add to Collection

Article Chemistry, Physical

Reinforcement with graphene nanoflakes in titanium matrix composites

Zhen Cao et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructural and mechanical characterization of in-situ TiC/Ti titanium matrix composites fabricated by graphene/Ti sintering reaction

Xinjiang Zhang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of carbon nanotubes reinforced titanium matrix composites fabricated via spark plasma sintering

Khurram S. Munir et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Characterisation of corrosion properties of Ti-Nb-Cu alloy foam by electrochemical impedance spectroscopy method

I. Mutlu et al.

CORROSION ENGINEERING SCIENCE AND TECHNOLOGY (2016)

Add to Collection

Article Materials Science, Multidisciplinary

On the selection of Ti-Cu alloys for thixoforming processes: phase diagram and microstructural evaluation

Kaio Niitsu Campo et al.

JOURNAL OF MATERIALS SCIENCE (2015)

Add to Collection

Article Materials Science, Biomaterials

Effect of Cu content on the antibacterial activity of titanium-copper sintered alloys

Jie Liu et al.

MATERIALS SCIENCE & ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS (2014)

Add to Collection

Article Engineering, Mechanical

Friction and wear behavior of titanium matrix (TiB plus TiC) composites

I. Y. Kim et al.

WEAR (2011)

Add to Collection

Article Chemistry, Multidisciplinary

Frictional Characteristics of Nano-Scale Mesoporous SiO2 Thin Film Formed by Sol-Gel and Self-Assembly Method

Gyu-Sun Lee et al.

JOURNAL OF NANOSCIENCE AND NANOTECHNOLOGY (2009)

Add to Collection

© Peeref 2019-2024. All rights reserved.