☆ 4.7 Article

Synergistic effect of Al3(Er, Zr) precipitation and hot extrusion on the microstructural evolution of a novel Al-Mg-Si-Er-Zr alloy

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Hot deformation behaviour and microstructure evolution of Al-3% Mg2Si alloy

Min Hu et al.

Summary: Isothermal compression tests were conducted on the Al-3%Mg2Si alloy in the temperature range of 300-500°C and strain rate range of 0.01-5 s-1, revealing typical dynamic recovery characteristics in the flow stress curves. A modified Arrhenius-type constitutive equation was established to describe the flow behavior. Microstructure evolution was analyzed based on the processing map. High efficiency of power dissipation regions was attributed to softening mechanisms of dynamic recovery and partial dynamic recrystallization, with Mg2Si particles also playing a positive role in the latter. Damage mechanism of unstable domains was identified as fracture and debonding of Mg2Si particles.

MATERIALS CHARACTERIZATION (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure, superplasticity, and mechanical properties of Al-Mg-Er-Zr alloys

A. D. Kotov et al.

Summary: Minor additions of rare-earth elements have been found to enhance the mechanical properties of aluminum-based alloys by improving precipitation strengthening and increasing resistance to recrystallization. This study investigated the microstructure, mechanical properties, and superplasticity of Al-Mg-Z-Er alloys with varying Mg content. The results showed that an increase in Mg content led to solid solution strengthening and facilitated dynamic recrystallization at high temperatures. The presence of fine L12 precipitates and (Al,Mg)3Er particles resulted in a fine-grained structure and excellent superplastic deformation behavior.

MATERIALS CHARACTERIZATION (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Hot deformation behavior and microstructure evolution of hot-extruded 6A02 aluminum alloy

Ying Zhang et al.

Summary: This work investigated the effects of temperature, strain rate, strain and initial orientation on the hot-compression behavior and microstructural evolution of hot-extruded 6A02 aluminum alloy. The results showed that higher temperature and lower strain rate led to lower geometrically necessary dislocation density, lower stored strain energy, and higher dynamic recrystallization degree. The continuous dynamic recrystallization mechanism was superior to the discontinuous dynamic recrystallization mechanism.

MATERIALS CHARACTERIZATION (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of TiC nanoparticles on the hot deformation behavior of AA7075 aluminum alloy

Cheng Cong Huang et al.

Summary: The hot deformation behaviors of AA7075 aluminum alloy and nano-treated AA7075 aluminum alloy were compared at high temperatures, revealing that the latter exhibited deteriorated hot processing properties and increased instability region, resulting in more microvoids and microcracks. The flow stress of nano-treated AA7075 was higher than that of AA7075 at lower temperatures, but the difference decreased at higher temperatures. The microstructures analysis showed that the mixed particles of TiC and MgZn2 played a key role in pinning dislocations and inhibiting grain growth during deformation.

MATERIALS CHARACTERIZATION (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Hot deformation and dynamic recrystallization in Al-Mg-Si alloy

Jiachen Li et al.

Summary: The hot deformation behavior of Al-Mg-Si alloys was studied through isothermal compression tests, revealing that the dynamic recrystallization mechanism depends on the Zener-Hollomon values. Three different DRX mechanisms were observed during the experimental process.

MATERIALS CHARACTERIZATION (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Dynamic softening mechanisms and Zener-Hollomon parameter of Al-Mg-Si-Ce-B alloy during hot deformation

Yi Yu et al.

Summary: Isothermal hot compression tests were conducted on Al-Mg-Si-Ce-B alloy at temperatures from 623-823 K with strain rates of 0.01-50 s-1. The alloy showed plastic deformation instability at relatively low temperatures, with optimized deformation parameters identified as 783-823 K/0.03-0.04 s. The microstructure was characterized using TEM and EBSD, and the influence of Z parameter on dynamic softening mechanisms was discussed, showing both DRV and CDRX as softening mechanisms during hot deformation.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Chemistry, Physical

Effects of Al(MnFe)Si dispersoids with different sizes and number densities on microstructure and ambient/elevated-temperature mechanical properties of extruded Al-Mg-Si AA6082 alloys with varying Mn content

Jovid Rakhmonov et al.

Summary: The study showed that fine dispersoids were more effective in increasing the alloy's resistance to plastic deformation during extrusion compared to coarse dispersoids. At ambient temperature, the 0.5% Mn-containing alloy exhibited substantial strengthening effects; however, increasing the Mn content led to a decline in mechanical properties.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Evolution of Zr-Bearing Dispersoids during Homogenization and Their Effects on Hot Deformation and Recrystallization Resistance in Al-0.8%Mg-1.0%Si Alloy

A. Elasheri et al.

Summary: The investigation found that different types of Zr-bearing dispersoids can be produced under different homogenization conditions after Zr addition. In hot compression testing, Zr-bearing dispersoids can increase high-temperature flow stress and inhibit dislocation motion and dynamic recovery. During post-deformation annealing, these dispersoids have a positive impact on recrystallization inhibition.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Enhanced high-temperature age-hardening behavior and mechanical properties of Al-Mg-Si alloys via microalloying with Cd

Gang Lu et al.

Summary: The addition of trace Cd not only accelerated the precipitation kinetics and increased the peak hardness of Al-Mg-Si alloys, but also refined the size and increased the number density of the precipitates. The Cd addition also improved the room-temperature tensile properties of the alloy, enhancing yield strength and total elongation due to the refined precipitate microstructure and narrowed precipitate-free zone along the grain boundaries.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

The constitutive modeling and processing map of homogenized Al-Mg-Si-Cu-Zn alloy

Tao Wei et al.

Summary: The true stress-strain curve of Al-Mg-Si-Cu-Zn alloy under high temperature and high strain rate conditions was obtained, and the constitutive equation was established. The optimum hot working window was determined based on the comparison of predicted values from the model with experimental values.

MATERIALS TODAY COMMUNICATIONS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Simulation of dynamic recrystallization in an Al-Mg-Si alloy during inhomogeneous hot deformation

Jiachen Li et al.

Summary: The study investigated the hot deformation behaviors of Al-Mg-Si alloys at different temperatures and strain rates, revealing the patterns of uneven dynamic recrystallization distribution, and establishing a corresponding dynamic recrystallization kinetic model.

MATERIALS TODAY COMMUNICATIONS (2021)

Add to Collection

Article Chemistry, Physical

Study on the dynamic recrystallization mechanisms of Inconel 740 superalloy during hot deformation

M. J. Wang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Chemistry, Physical

Effect of Al3(Sc, Zr) and Mg2Si precipitates on microstructure and tensile properties of selective laser melted Al-14.1Mg-0.47Si-0.31Sc-0.17Zr alloy

Jiang Bi et al.

INTERMETALLICS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of Mn content on recrystallization resistance of AA6082 aluminum alloys during post-deformation annealing

Xiaoming Qian et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Effects of Mn addition and related Mn-containing dispersoids on the hot deformation behavior of 6082 aluminum alloys

Xiaoming Qian et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Deformation characteristics and strain-compensated constitutive equation for AA5083 aluminum alloy under hot compression

Qing-song Dai et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Characterization of hot deformation behavior and constitutive modeling of Al-Mg-Si-Mn-Cr alloy

Shuhui Liu et al.

JOURNAL OF MATERIALS SCIENCE (2019)

Add to Collection

Article Chemistry, Physical

Effect of Heat Treatment Condition on the Flow Behavior and Recrystallization Mechanisms of Aluminum Alloy 7055

Bin Liao et al.

MATERIALS (2019)

Add to Collection

Article Chemistry, Physical

3D processing map and hot deformation behavior of 6A02 aluminum alloy

Yu Sun et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Clustering behavior during natural aging and artificial aging in Al-Mg-Si alloys with different Ag and Cu addition

Yaoyao Weng et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Hot deformation behavior of a Sr-modified Al-Si-Mg alloy: Constitutive model and processing maps

Y. C. Lin et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Evolutions of diffusion activation energy and Zener-Hollomon parameter of ultra-high strength Al-Zn-Mg-Cu-Zr alloy during hot compression

Yuanwei Sun et al.

PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL (2018)

Add to Collection

Article Chemistry, Physical

Study on hot deformation behavior and intrinsic workability of 6063 aluminum alloys using 3D processing map

Yang Liu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

Add to Collection

Article Chemistry, Physical

Microstructure analysis of an Al-Zn-Mg alloy during porthole die extrusion based on modeling of constitutive equation and dynamic recrystallization

Gaojin Chen et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

Add to Collection

Article Chemistry, Physical

Effects of Er/Sr/Cu additions on the microstructure and mechanical properties of Al-Mg alloy during hot extrusion

Hongmei Che et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Prediction of the Hot Flow Stress Behavior of AA6063 Including Mg2Si Dissolution

Daniel Odoh et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2017)

Add to Collection

Article Chemistry, Physical

Hot deformation behavior and processing map of a new type Al-Zn-Mg-Er-Zr alloy

H. Wu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Hot deformation behavior and constitutive equation of a new type Al-Zn-Mg-Er-Zr alloy during isothermal compression

H. Wu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Hot deformation behavior and optimization of processing parameters of a typical high-strength Al-Mg-Si alloy

Xizhou Kai et al.

MATERIALS & DESIGN (2016)

Add to Collection

Article Materials Science, Composites

Hot deformation behavior of in situ nano ZrB2 reinforced 2024Al matrix composite

Xizhou Kai et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2015)

Add to Collection

Article Chemistry, Physical

Characterization of hot deformation behavior of an extruded Mg-Zn-Mn-Y alloy containing LPSO phase

N. Tahreen et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Hot deformation behavior and processing map of Al-Si-Mg alloys containing different amount of silicon based on Gleebe-3500 hot compression simulation

Hengcheng Liao et al.

MATERIALS & DESIGN (2015)

Add to Collection

Article Materials Science, Multidisciplinary

New constitutive model for high-temperature deformation behavior of inconel 718 superalloy

Y. C. Lin et al.

MATERIALS & DESIGN (2015)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Simple physically-based constitutive equations for hot deformation of 2024 and 7075 aluminum alloys

Hamed Mirzadeh

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Hot deformation and processing map of an as-extruded Mg-Zn-Mn-Y alloy containing I and W phases

N. Tahreen et al.

MATERIALS & DESIGN (2015)

Add to Collection

Article Materials Science, Multidisciplinary

The flow behavior and constitutive equation in isothermal compression of FGH4096-GH4133B dual alloy

Yanhui Liu et al.

MATERIALS & DESIGN (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Hot deformation mechanisms, microstructure and texture evolution in extruded AZ31-nano-alumina composite

T. Zhong et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Characterization of hot deformation behavior of as-homogenized Al-Cu-Li-Sc-Zr alloy using processing maps

Bo Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Investigation of work softening mechanisms and texture in a hot deformed 6061 aluminum alloy at high temperature

H. R. Ezatpour et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Hot deformation behavior of as-quenched 7005 aluminum alloy

Ming-liang Wang et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Process Variables on Mg-Si Particles and Extrudability of 6xxx Series Aluminum Extrusions

Hanliang Zhu et al.

JOM (2011)

Add to Collection

Article Nanoscience & Nanotechnology

Synergetic effect of Er and Zr on the precipitation hardening of Al-Er-Zr alloy

S. P. Wen et al.

SCRIPTA MATERIALIA (2011)

Add to Collection

Article Nanoscience & Nanotechnology

The effect of erbium on the microstructure and mechanical properties of Al-Mg-Mn-Zr alloy

S. P. Wen et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)

Add to Collection

Article Materials Science, Multidisciplinary

Quantitative study on the precipitation behavior of dispersoids in DC-cast AA3003 alloy during heating and homogenization

YJ Li et al.

ACTA MATERIALIA (2003)

Add to Collection

Article Materials Science, Multidisciplinary

Roles of microalloying elements on the cluster formation in the initial stage of phase decomposition of Al-based alloys

T Sato et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2003)

Add to Collection

Article Nanoscience & Nanotechnology

Texture control by thermomechanical processing of AA6xxx Al-Mg-Si sheet alloys for automotive applications -: a review

O Engler et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2002)

Add to Collection

© Peeref 2019-2024. All rights reserved.