Related references
Note: Only part of the references are listed.Friction stir butt-welding of roll cladded aluminum thin sheets: effect of microstructural and texture changes on mechanical properties
Soumyabrata Basak et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)
Effect of Delamination and Grain Refinement on Fracture Energy of Ultrafine-Grained Steel Determined Using an Instrumented Charpy Impact Test
Tadanobu Inoue et al.
MATERIALS (2022)
A new strategy for fabrication of unique heterostructured titanium laminates and visually tracking their synchronous evolution of strain partitions versus microstructure
Hao Ding et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)
Effect of warm-rolling on the strength and ductility of multilayered composite steel
Jingyu Li et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)
Study of forming limit curves and mechanical properties of three-layered brass (CuZn10)/low carbon steel (St14) /brass (CuZn10) composite considering the effect of annealing temperature
Mohammad Delshad Gholami et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)
Ductile-to-Brittle Transition and Brittle Fracture Stress of Ultrafine-Grained Low-Carbon Steel
Tadanobu Inoue et al.
MATERIALS (2021)
Forming of metal-based composite parts
S. Bruschi et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2021)
Deformation Behavior and Strengthening Mechanisms of Multilayer SUS304/Cr17 Steels with Laminate/Network Interface
B. X. Liu et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)
Mechanical Property of Ultrafine Elongated Grain Structure Steel Processed by Warm Tempforming and Its Application to Ultra High-Strength Bolt
Yuuji Kimura et al.
ISIJ INTERNATIONAL (2020)
A new route to fabricate multilayer steel with multiscale hierarchical structure
B. Y. Zhang et al.
MATERIALS CHARACTERIZATION (2020)
A novel strengthening and toughening strategy for T250 maraging steel: Cluster-orientation governed higher strength-ductility combination induced by electropulsing
Dong Pan et al.
MATERIALS & DESIGN (2019)
Hardening by slip-twin and twin-twin interactions in FeMnNiCoCr
M. Bonisch et al.
ACTA MATERIALIA (2018)
Microstructure, mechanical properties and interface bonding mechanism of hot-rolled stainless steel clad plates at different rolling reduction ratios
S. Wang et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2018)
Ultrastrong steel via minimal lattice misfit and high-density nanoprecipitation
Suihe Jiang et al.
NATURE (2017)
Ultrahigh Charpy impact toughness (∼450J) achieved in high strength ferrite/martensite laminated steels
Wenquan Cao et al.
SCIENTIFIC REPORTS (2017)
Structural characteristics of Cu/Ti bimetal composite produced by accumulative roll-bonding (ARB)
M. Hosseini et al.
MATERIALS & DESIGN (2017)
Effect of interface oxides on shear properties of hot-rolled stainless steel clad plate
Zhichao Zhu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
The Kinetics of TiAl3 Formation in Explosively Welded Ti-Al Multilayers During Heat Treatment
Farzad Foadian et al.
METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE (2016)
Stress strain behavior of ferrite and bainite with nano-precipitation in low carbon steels
Naoya Kamikawa et al.
ACTA MATERIALIA (2015)
Strain rate dependent tensile plasticity of ultrafine-grained Cu/Ni laminated composites
H. F. Tan et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Development of Multilayer Steels for Improved Combinations of High Strength and High Ductility
Toshihiko Koseki et al.
MATERIALS TRANSACTIONS (2014)
Interfacial Microstructure and Properties of Carbon Fiber Composites Modified with Graphene Oxide
Xiaoqing Zhang et al.
ACS APPLIED MATERIALS & INTERFACES (2012)
Dependence of tensile deformation behavior of TWIP steels on stacking fault energy, temperature and strain rate
S. Curtze et al.
ACTA MATERIALIA (2010)
Effect of interfacial bonding strength on tensile ductility of multilayered steel composites
S. Nambu et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2009)
Are nanotwinned structures in fcc metals optimal for strength, ductility and grain stability?
Yashashree Kulkarni et al.
SCRIPTA MATERIALIA (2009)
Inverse temperature dependence of toughness in an ultrafine grain-structure steel
Yuuji Kimura et al.
SCIENCE (2008)
Fracture elongation of brittle/ductile multilayered steel composites with a strong interface
Junya Inoue et al.
SCRIPTA MATERIALIA (2008)
Clad metals, roll bonding and their applications for SOFC interconnects
LC Chen et al.
JOURNAL OF POWER SOURCES (2005)
Tensile properties of copper with nano-scale twins
YF Shen et al.
SCRIPTA MATERIALIA (2005)
Reaction synthesis and microstructures of NiAl/Ni micro-laminated composites
HY Kim et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2005)
The relationship between hardness and yield stress in irradiated austenitic and ferritic steels
JT Busby et al.
JOURNAL OF NUCLEAR MATERIALS (2005)
Ancient blacksmiths, the Iron Age, Damascus steels, and modem metallurgy
OD Sherby et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)
Share Paper
