☆ 4.5 Article

Microstructure Evolution Behavior of Spray-Deposited 7055 Aluminum Alloy during Hot Deformation

METALS (2022)

Related references

Note: Only part of the references are listed.

Article Metallurgy & Metallurgical Engineering

Effect of non-isothermal retrogression and re-ageing on through-thickness homogeneity of microstructure and properties of Al-8Zn-2Mg-2Cu alloy thick plate

Wu Cai-hong et al.

Summary: The through-thickness homogeneity and properties of aviation aluminum alloy thick plate can be improved by heating-cooling retrogression and re-ageing treatment. The research findings indicated that the coarsening and secondary precipitation behaviors of precipitates can be controlled under suitable retrogression and cooling conditions, leading to enhanced electrical conductivity and through-thickness homogeneity of the alloy plate.

JOURNAL OF CENTRAL SOUTH UNIVERSITY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of thermo-mechanical conditions on the microstructure and mechanical property of spray-formed 7055 aluminum alloy

Yong Shao et al.

Summary: A series of isothermal compression experiments were conducted to investigate the flow behavior of spray-formed 7055 aluminum alloy under different thermo-mechanical conditions. The results showed that the dynamic softening mechanisms, material flow behavior, microstructure development, and texture evolution were influenced by the deformation conditions. Additionally, the relationship between dynamic recrystallization mechanisms and hot deformation conditions, as well as the impact of chemical composition and morphological changes on microstructure, were studied.

MATERIALS TODAY COMMUNICATIONS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Precipitation behavior of spray-formed aluminum alloy 7055 during high temperature aging

Xiaomin Lin et al.

Summary: The precipitation behavior of spray-formed aluminum alloy 7055 during high temperature aging was studied, and the results showed that eta phase was the main precipitate. The most suitable aging treatment was found to be 400 degrees C for 2 minutes, which resulted in the formation of finer eta phases and improved hardness and conductivity.

MATERIALS CHARACTERIZATION (2022)

Add to Collection

Article Materials Science, Multidisciplinary

In situ laser-ultrasonic monitoring of elastic parameters during natural aging in an Al-Zn-Mg-Cu alloy (AA7075) sheet

Georg Watzl et al.

Summary: In this study, an in situ laser ultrasonic method based on plate resonances was used to continuously monitor small changes (<1%) of Young's modulus, shear modulus, and Poisson's ratio during natural aging of an age-hardenable aluminum alloy (AA7075) sheet. The formation of Guinier-Preston zones was found to be qualitatively correlated with an increase in elastic moduli and material strength.

MATERIALIA (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Study on ductile fracture of unweldable spray formed 7055 aluminum alloy TIG welded joints with ceramic particles

Ting Huang et al.

Summary: This study developed aluminum alloy welding wires containing TiB2 and ZrB2 ceramic particles, successfully introducing them into the welded joints of spray formed 7055 aluminum alloy to improve the strength and ductility of the joints, providing new possibilities for the application of aluminum alloys.

MATERIALS TODAY COMMUNICATIONS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Hot workability and dynamic recrystallization behavior of a spray formed 7055 aluminum alloy

Rui Luo et al.

Summary: In this study, the hot workability of a spray formed 7055 aluminum alloy was investigated using advanced Gleeble thermo-mechanical simulation technology and EBSD technology. It was found that with increasing deformation parameters, the grains become finer and the distribution of crystal orientation becomes more homogeneous. Additionally, both Continuous Dynamic Recrystallization (CDRX) and Discontinuous Dynamic Recrystallization (DDRX) mechanisms coexist during hot deformation.

MATERIALS CHARACTERIZATION (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Simulation of low proportion of dynamic recrystallization in 7055 aluminum alloy

Jia-chen Li et al.

Summary: The study investigated the hot deformation and DRX behaviors of 7055 aluminum alloy, proposing a modified model for low DRX fraction problems. The simulation results showed good agreement with experimental observations, confirming the validity of the proposed model for industrial applications.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of heat treatment on the precipitate behaviour, corrosion resistance and high temperature tensile properties of 7055 aluminum alloy synthesis by novel spray deposited followed by hot extrusion

Muhammad Abubaker Khan et al.

VACUUM (2020)

Add to Collection

Article Materials Science, Multidisciplinary

The strengthening mechanism of FSWed spray formed 7055 aluminum alloy under water mist cooling condition

Yumo Jiang et al.

MATERIALS CHARACTERIZATION (2020)

Add to Collection

Article Chemistry, Physical

Improvement of anisotropic tensile properties of Al-7.9Zn-2.7Mg-2.0Cu alloy sheets by particle stimulated nucleation

Qianhao Zang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure Evolution and Recrystallization Resistance of a 7055 Alloy Fabricated by Spray Forming Technology and by Conventional Ingot Metallurgy

Zhiqiang Xie et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of initial microstructure on hot deformation behavior of Al-7.9Zn-2.7Mg-2.0Cu (wt%) alloy

Qianhao Zang et al.

MATERIALS CHARACTERIZATION (2019)

Add to Collection

Article Chemistry, Physical

Effect of Zn content on the static softening behavior and kinetics of Al-Zn-Mg-Cu alloys during double-stage hot deformation

Jie Tang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Engineering, Manufacturing

Effect of welding speed on performance of friction stir welded spray forming 7055 aluminum alloy

Shengchong Ma et al.

JOURNAL OF MANUFACTURING PROCESSES (2019)

Add to Collection

Article Chemistry, Physical

The effects of aging treatments on mechanical property and corrosion behavior of spray formed 7055 aluminium alloy

L. L. Liu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of grain size inhomogeneity of ingot on dynamic softening behavior and processing map of Al-8Zn-2Mg-2Cu alloy

Di Feng et al.

METALS AND MATERIALS INTERNATIONAL (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Flow behavior and microstructure evolution of 7055 aluminum alloy impacted at high strain rates

Shengdan Liu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Effects of strain rate on flow stress behavior and dynamic recrystallization mechanism of Al-Zn-Mg-Cu aluminum alloy during hot deformation

Qunying Yang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Review Materials Science, Multidisciplinary

A review of dynamic recrystallization phenomena in metallic materials

K. Huang et al.

MATERIALS & DESIGN (2016)

Add to Collection

Article Chemistry, Physical

Combined effect of hot extrusion and heat treatment on the mechanical behavior of 7055 AA processed via spray metal forming

J. M. Schreiber et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Constitutive equation and hot deformation behavior of homogenized Al-7.68Zn-2.12Mg-1.98Cu-0.12Zr alloy during compression at elevated temperature

D. Feng et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Chemistry, Physical

Microstructure and tensile properties of large-size 7055 aluminum billets fabricated by spray forming rapid solidification technology

Yu Hongchun et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2013)

Add to Collection

© Peeref 2019-2024. All rights reserved.