Related references
Note: Only part of the references are listed.
Article
Engineering, Mechanical
Kun Zhou et al.
Summary: This study uses electroplated diamond abrasive belts (EDAB) to grind Inconel718. It is found that EDAB shows stable grinding performance, and the wear mechanism in different wear stages is primarily micro cleavage fracture, macro cleavage fracture, and adhesive wear. With the wear of EDAB, the surface roughness decreases and reaches a minimum of Ra0.5μm, and the subsurface crystalline grains of Inconel718 are refined. Furthermore, the use of low-hardness contact wheels significantly reduces abrasive belt wear and improves surface integrity.
TRIBOLOGY INTERNATIONAL
(2023)
Article
Chemistry, Physical
Shuai Liu et al.
Summary: A new and efficient method of laser belt processing was proposed for the preparation of Inconel 718 surfaces with ultrahigh adhesion and anisotropic wettability. The microgroove depth could be increased without changing processing parameters, and microporous structures with nanoparticles were introduced. The results showed that the surface wetting state was between the Wenzel and Cassie wetting states, and van der Waals forces provided ultrahigh adhesion. Anisotropic wettability increased with increasing laser power, and the presence of nanoparticles enhanced the anisotropy.
APPLIED SURFACE SCIENCE
(2023)
Review
Engineering, Civil
Munish Kumar Gupta et al.
Summary: Grade titanium and its alloys are important choices for the automotive, biomedical, and aerospace industries due to their easy fabrication, weldability, biocompatibility, high strength-to-weight ratio, high temperature resistance, and low modulus of elasticity. However, the tribological and surface morphological characteristics of Ti-6Al-4V alloy are limited. Various attempts and studies have been conducted to enhance these properties.
ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING
(2022)
Review
Automation & Control Systems
Weijie Kuang et al.
Summary: Mechanical friction leads to significant energy consumption annually. Decreasing friction and wear and prolonging the service life of components are crucial for energy sustainable development. Researchers investigate how to improve the tribological and wear resistance of components through mechanical machining. This article reviews the influence of common mechanical processes on the wear performance of machined surfaces, including hardness, surface morphology, and residual stresses.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
(2022)
Article
Engineering, Industrial
Kun Zhou et al.
Summary: This study proposes a novel high-efficiency, low-damage, and low-abrasive wear processing method for continuous fiber-reinforced ceramic matrix composites. The method combines laser ablation and grinding, resulting in improved grinding performances and surface integrity. The study provides an important method for high-performance processing of ceramic matrix composites components.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
(2022)
Article
Engineering, Mechanical
Wenxi Wang et al.
Summary: In this study, a physical modeling and numerical calculation approach was developed to investigate the mechanism of surface roughness formation in abrasive belt rail grinding. The proposed method was verified through grinding experiments.
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING
(2022)
Article
Materials Science, Coatings & Films
Chao Wang et al.
Summary: In this study, simultaneous laser nitriding and texturing of Ti6Al4V surface were achieved through nanosecond pulse laser irradiation in a nitrogen atmosphere. The effects of laser parameters on surface hardness and tribological properties were studied. The results showed significant improvements in surface hardness and friction coefficient after simultaneous laser nitriding and texturing, with different scratching characteristics under various irradiation parameters.
SURFACE & COATINGS TECHNOLOGY
(2022)
Article
Engineering, Manufacturing
Tao Chen et al.
Summary: This article establishes a new simulation model to predict the residual stresses of turbine blade root during creep feed profile grinding (CFPG). The study finds that the grinding-induced residual stresses in different areas of the blade root are either tensile or compressive. The residual stresses in the stable stage are greater than those in the cut-in and cut-out stages, and without considering these stages, the residual stresses remain constant.
JOURNAL OF MANUFACTURING PROCESSES
(2022)
Article
Engineering, Manufacturing
Chengsong Shu et al.
Summary: Controllable manipulation of droplets over a wide temperature range is of great significance in various fields, but fabricating a controllable droplet manipulation platform using commonly used industrial methods remains a challenge. In this study, we developed a simple and industrially applicable method to prepare superhydrophobic aluminum surfaces, enabling controlled droplet bouncing, evaporation, and transport in a wide temperature range. Through systematic investigations, we achieved controlled droplet transport with confluence, split-flow, and gravity resistance by utilizing Laplace pressure gradients and temperature gradients on extreme wettability surfaces. This platform offers potential applications in areas such as drug candidates and water collection.
INTERNATIONAL JOURNAL OF EXTREME MANUFACTURING
(2022)
Article
Materials Science, Ceramics
Tao Chen et al.
Summary: TiC/TiB composite bioinert ceramic coatings were synthesized in-situ via laser cladding using Ti and B4C mixed powders. Subsequent heat treatment at different temperatures enhanced the mechanical properties and wear resistance of the coatings while maintaining their microstructure and phase compositions. The coatings showed improved fracture toughness and wear resistance after heat treatment, and exhibited good biocompatibility in vitro.
CERAMICS INTERNATIONAL
(2021)
Article
Engineering, Mechanical
G. Boidi et al.
Summary: This study demonstrated the potential of fast laser texturing techniques in improving the tribological performance of bearings and mechanical components. Dimples were found to reduce friction effectively compared to smooth surfaces, while grooves had less beneficial effects. Additionally, dimples promoted the formation of full film lubrication conditions at lower speeds.
Article
Engineering, Mechanical
Ying Meng et al.
Summary: Micro-textures fabricated by laser texturing and ultrasonic rolling texturing can improve the tribological properties of TiAlSiN coatings, reduce friction coefficient and wear rate, and amplify lubrication effect.
TRIBOLOGY INTERNATIONAL
(2021)
Article
Engineering, Mechanical
Junyuan Huang et al.
Summary: The tribological behavior of femtosecond laser-textured leaded brass samples was studied under different surface roughness and lubrication conditions. The coefficient of friction exhibited consistent changes under various lubrication conditions, with the roughness affecting the friction coefficient. The wear mechanisms were mainly adhesive wear and abrasive wear, with differences in specific wear mechanisms observed under various friction conditions.
TRIBOLOGY INTERNATIONAL
(2021)
Review
Automation & Control Systems
Ze Wu et al.
Summary: This paper mainly introduces the manufacturing methods of surface texture, including classification methods based on different processing principles, and the importance of selecting appropriate processing techniques and parameters to obtain high-quality surface texture.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
(2021)
Article
Engineering, Mechanical
P. Budzynski et al.
Summary: The tribological properties of titanium and Ti6Al4V alloy are altered by irradiation with swift xenon ions, leading to unconventional changes in friction coefficient and crystal lattice parameters. These changes are attributed to annealing and evolution of radiation defects during high fluence Xe-ion irradiation, with two-step changes in friction coefficient of titanium observed for the first time.
TRIBOLOGY INTERNATIONAL
(2021)
Article
Engineering, Manufacturing
Kaiyuan You et al.
Summary: The study investigates the removal mechanism of binderless polycrystalline tungsten carbide material through conventional cutting and in-process-heat laser-assisted cutting. The results show that the high-temperature nanoindentation test reveals improved machinability of WC at an elevated temperature, and the optimal laser power for obtaining a better surface finish ranges from 10 W to 15 W.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
(2021)
Article
Engineering, Mechanical
M. Conradi et al.
Summary: The study found that under different sliding conditions, dimples defined by nanosecond laser exhibited the lowest steady-state coefficient of friction, while in Hank's solution, lines and crosshatching showed better frictional characteristics after running-in and the removal of bulges around the laser textures. In terms of wear resistance, low-density lines pattern and particularly dimples were the most promising in contact situations likely to occur during starved/dry-lubrication conditions.
TRIBOLOGY INTERNATIONAL
(2021)
Review
Engineering, Multidisciplinary
Guijian Xiao et al.
Summary: The text discusses the impact of sharkskin surface structural characteristics on aerodynamic performance, focusing on the processing and simulation of different Bionic-Ribbed Structures (BRS) on a blade. Results show that increasing the tip angle reduces the low-velocity layer near BRS while increasing wall shear stress, with the best performance observed at a 45-degree tip angle.
JOURNAL OF BIONIC ENGINEERING
(2021)
Article
Engineering, Manufacturing
Zhendong Shang et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
(2019)
Article
Engineering, Manufacturing
Miguel Arizmendi et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
(2019)
Article
Materials Science, Multidisciplinary
Zhen Chen et al.
RESULTS IN PHYSICS
(2019)
Review
Chemistry, Physical
Naiming Lin et al.
Article
Metallurgy & Metallurgical Engineering
Dinesh P. Babu et al.
JOURNAL OF CENTRAL SOUTH UNIVERSITY
(2018)
Article
Engineering, Mechanical
M. Adjemout et al.
TRIBOLOGY INTERNATIONAL
(2017)
Article
Materials Science, Coatings & Films
Maedeh Sadat Zoei et al.
SURFACE & COATINGS TECHNOLOGY
(2016)
Article
Engineering, Mechanical
Zhuo Wang et al.
TRIBOLOGY INTERNATIONAL
(2016)
Article
Materials Science, Coatings & Films
F. M. El-Hossary et al.
SURFACE & COATINGS TECHNOLOGY
(2015)
Article
Engineering, Mechanical
Andreas Rosenkranz et al.
Article
Engineering, Manufacturing
J. Xie et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
(2013)
Article
Engineering, Manufacturing
Rendi Kurniawan et al.
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING
(2013)
Article
Engineering, Mechanical
Piotr Stepien
Article
Engineering, Chemical
I Etsion
