☆ 4.7 Article

Combination resonances of rotor systems with asymmetric residual preloads in bolted joints

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2023)

Related references

Note: Only part of the references are listed.

Article Engineering, Mechanical

Experimental and theoretical approaches for determining cage motion dynamic characteristics of angular contact ball bearings considering whirling and overall skidding behaviors

Shuai Gao et al.

Summary: This study proposed a comprehensive bearing dynamic model focused on cage characteristics and introduced several indicators describing cage stability and skidding degree based on experimental and theoretical results. It identified factors affecting bearing skidding and instability of the cage.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2022)

Add to Collection

Article Engineering, Mechanical

Dynamic characteristics of an aeroengine dual-rotor system with inter-shaft rub-impact

Pingchao Yu et al.

Summary: This paper investigates the nonlinear dynamics of a dual-rotor system with inter-shaft rub-impact, using a 3D finite solid element method. An analysis strategy combining the component mode synthesis method and numerical integration method is developed to clarify the modes and vibration responses of the system. The results show the novel resonance peaks and different rubbing types that may be excited, along with the effects of rubbing stiffness and friction coefficient on eliminating dangerous self-excited rubbing vibrations.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2022)

Add to Collection

Article Engineering, Mechanical

Study on local slippage accumulation between thread contact surfaces and novel anti-loosening thread designs under transversal vibration

Hao Gong et al.

Summary: The study developed novel algorithms to simulate the cumulative process of local slippage based on modified Iwan models, confirming the reliability of previous theoretical analytical results. The mechanism of local slippage accumulation was revealed and critical local slippage accumulation was studied. The proposed novel thread structures showed superior anti-loosening performance compared to existing products, and were easy to install and remove.

TRIBOLOGY INTERNATIONAL (2021)

Add to Collection

Article Engineering, Multidisciplinary

Dynamic modelling and vibration characteristics analysis for the bolted joint with spigot in the rotor system

Pingchao Yu et al.

Summary: This study proposed a new analytical model of bolted joint to effectively describe the joint's nonlinearity and damping. The bolted joint mainly causes stiffness loss and damping nonlinearity in the rotor system, which can be reduced by decreasing flange length, friction coefficient, and interference fit of the spigot.

APPLIED MATHEMATICAL MODELLING (2021)

Add to Collection

Article Engineering, Aerospace

Modal analysis strategy and nonlinear dynamic characteristics of complicated aero-engine dual-rotor system with rub-impact

Pingchao YU et al.

Chinese Journal of Aeronautics (2021)

Add to Collection

Article Engineering, Mechanical

A method for calculating radial time-varying stiffness of flexible cylindrical roller bearings with localized defects

Hongyang Xu et al.

Summary: This paper investigates a method for calculating the radial time-varying stiffness of flexible cylindrical roller bearings with localized defects, which utilizes finite element method and analytical contact theory. The proposed method shows higher calculation accuracy and improved computational efficiency compared to classical methods and finite element method. Results indicate that increasing the angle of defect width leads to a gradual increase in stiffness saltation.

ENGINEERING FAILURE ANALYSIS (2021)

Add to Collection

Article Engineering, Mechanical

Fault feature analysis of planetary gear set influenced by cracked gear tooth and pass effect of the planet gears

Hongzheng Han et al.

Summary: The study calculates the time-varying mesh stiffness of planetary gear sets considering gear crack faults using a loaded tooth contact analysis method, and verifies the correctness of an improved dynamic model through simulation results showing amplitude modulation and frequency modulation phenomena. It is found that ring gear crack faults rarely affect the dynamic load sharing among external meshing gear pairs.

ENGINEERING FAILURE ANALYSIS (2021)

Add to Collection

Article Acoustics

Eigen and temporal characteristics of multi-frequency parametrically-excited rotor-oscillator systems

Allen Anilkumar et al.

Summary: The paper investigates the dynamics of a generic multi-rotor system where the rotor and stator have comparable inertia and compliances. Numerical integration of parametrically-excited equations for a representative dual-rotor case reveals complex frequency spectra and cyclically time-varying eigen-structure. The results suggest that even seemingly simple multi-frequency parametrically excited rotating systems exhibit complicated eigen and temporal characteristics.

JOURNAL OF SOUND AND VIBRATION (2021)

Add to Collection

Article Engineering, Aerospace

Nonlinear vibration response characteristics of a dual-rotor-bearing system with squeeze film damper

Xinxing Ma et al.

Summary: The study focuses on the influence of SFD on the nonlinear dynamic behavior of a dual-rotor system supported by rolling bearings. It is found that SFD can effectively suppress amplitude jumps in the system, but improper parameters may worsen vibration. The ball bearing clearance, unbalance, centralizing spring stiffness, and oil film clearance of SFD all have effects on the system's steady-state vibration responses.

CHINESE JOURNAL OF AERONAUTICS (2021)

Add to Collection

Article Acoustics

Nonlinear vibrations of a dual-rotor-bearing-coupling misalignment system with blade-casing rubbing

Yulin Jin et al.

Summary: This study investigates the nonlinear vibration characteristics of a dual-rotor-bearing-coupling misalignment system with blade-casing rubbing through numerical simulation and experimental measurement. By establishing a dynamic model and reducing the model order, the results show that the numerical and experimental results are consistent, revealing the nonlinear vibration characteristics of the system.

JOURNAL OF SOUND AND VIBRATION (2021)

Add to Collection

Article Engineering, Mechanical

Study on self-loosening mechanism of bolted joint under rotational vibration

Zhibin Li et al.

Summary: This paper proposed a theoretical criterion for self-loosening under rotational vibration and identified two forms of self-loosening failure. The study found that vibration amplitude and initial preload significantly influence bolt loosening, while vibration frequency has a minor effect.

TRIBOLOGY INTERNATIONAL (2021)

Add to Collection

Article Engineering, Mechanical

Behaviour of an angular contact ball bearing with three-dimensional cubic-like defect: A comprehensive non-linear dynamic model for predicting vibration response

Shuai Gao et al.

Summary: This paper proposes an advanced dynamic model to study asymmetric defects on angular contact ball bearing raceways. The results show that the circumferential size of the 3D defect significantly affects the contact force distribution, leading to impulse vibrations in the bearing system. Avoiding extension of defects in the circumferential direction and reducing the radial-axial load ratio can mitigate vibration impulses.

MECHANISM AND MACHINE THEORY (2021)

Add to Collection

Article Engineering, Mechanical

Dynamic investigation of aeroengine high pressure rotor system considering assembly characteristics of bolted joints

Wei Sun et al.

ENGINEERING FAILURE ANALYSIS (2020)

Add to Collection

Article Engineering, Mechanical

A new method for the estimation of bearing health state and remaining useful life based on the moving average cross-correlation of power spectral density

Lang Xu et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2020)

Add to Collection

Article Engineering, Mechanical

The effects of the crack location on the whirl motion of a breathing cracked rotor with rotational damping

Huichun Peng et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2019)

Add to Collection

Article Engineering, Mechanical

Self-loosening of bolted L-stub connections under a cyclic separating load

Jianhua Liu et al.

WEAR (2019)

Add to Collection

Article Engineering, Mechanical

Observations of variability and repeatability in jointed structures

M. R. W. Brake et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2019)

Add to Collection

Article Engineering, Mechanical

Optimization of dynamics of non-continuous rotor based on model of rotor stiffness

Jie Hong et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2019)

Add to Collection

Article Engineering, Mechanical

Analytical lump model for the nonlinear dynamic response of bolted flanges in aero-engine casings

Marc-Antoine Beaudoin et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2019)

Add to Collection

Article Engineering, Mechanical

Nonlinear modeling of structures with bolted joints: A comparison of two approaches based on a time-domain and frequency-domain solver

Robert Lacayo et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2019)

Add to Collection

Article Engineering, Mechanical

Study on self-loosening of bolted joints excited by dynamic axial load

Jianhua Liu et al.

TRIBOLOGY INTERNATIONAL (2017)

Add to Collection

Article Engineering, Mechanical

Nonlinear response analysis for a dual-rotor system with a breathing transverse crack in the hollow shaft

Zhenyong Lu et al.

NONLINEAR DYNAMICS (2016)

Add to Collection

Article Engineering, Mechanical

Bolt loosening at rotating joint interface and its influence on rotor dynamics

Zhaoye Qin et al.

ENGINEERING FAILURE ANALYSIS (2016)

Add to Collection

Article Engineering, Mechanical

Crack identification for rotating machines based on a nonlinear approach

A. A. Cavalini et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2016)

Add to Collection

Article Acoustics

Dynamic behavior of cracked rotor subjected to multisine excitation

Zbigniew Kulesza

JOURNAL OF SOUND AND VIBRATION (2014)

Add to Collection

Article Construction & Building Technology

Modified stiffness model for thick flange in built-up T-stub connections

Elie G. Hantouche et al.

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2013)

Add to Collection

Article Acoustics

On the finite element modeling of the asymmetric cracked rotor

Mohammad A. AL-Shudeifat

JOURNAL OF SOUND AND VIBRATION (2013)

Add to Collection

Article Engineering, Mechanical

Measured and estimated friction interface parameters in a nonlinear dynamic analysis

C. W. Schwingshackl et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2012)

Add to Collection

Article Acoustics

Detecting cracked rotors using auxiliary harmonic excitation

Jerzy T. Sawicki et al.

JOURNAL OF SOUND AND VIBRATION (2011)

Add to Collection

Article Acoustics

The influence of crack breathing and imbalance orientation angle on the characteristics of the critical speed of a cracked rotor

Li Cheng et al.

JOURNAL OF SOUND AND VIBRATION (2011)

Add to Collection

Article Instruments & Instrumentation

Localization of breathing cracks using combination tone nonlinear response

Gi-Woo Kim et al.

SMART MATERIALS AND STRUCTURES (2011)

Add to Collection

Article Engineering, Mechanical

A comprehensive theoretical, numerical and experimental approach for crack detection in power plant rotating machinery

C. M. Stoisser et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2008)

Add to Collection

Article Engineering, Mechanical

Dynamic behaviour of the Laval rotor with a transverse crack

Robert Gasch

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2008)

Add to Collection

Review Engineering, Mechanical

The strain energy release approach for modeling cracks in rotors: A state of the art review

Chris A. Papadopoulos

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2008)

Add to Collection

Article Engineering, Mechanical

Some remarks on breathing mechanism, on non-linear effects and on slant and helicoidal cracks

Nicolo Bachschmid et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2008)

Add to Collection

Article Acoustics

Cortical responses to the 2f1-f2combination tone measured indirectly using magnetoencephalography

David W. Purcell et al.

JOURNAL OF THE ACOUSTICAL SOCIETY OF AMERICA (2007)

Add to Collection

Article Engineering, Mechanical

Experimental and theoretical studies of a bolted joint excited by a torsional dynamic load

H. Ouyang et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2006)

Add to Collection

Article Acoustics

Active health monitoring in a rotating cracked shaft using active magnetic bearings as force actuators

G. Mani et al.

JOURNAL OF SOUND AND VIBRATION (2006)

Add to Collection

Article Engineering, Mechanical

Validity of bolt-removal and gap-insertion techniques to experimentally simulate the vibration of a cracked rotor

H Keiner et al.

FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2004)

Add to Collection

© Peeref 2019-2024. All rights reserved.