☆ 4.7 Article

Additive manufacturing of cemented carbides inserts with high mechanical performance

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Impact of cobalt content and grain growth inhibitors in laser-based powder bed fusion of WC-Co

Tobias Schwanekamp et al.

Summary: This paper investigates the impact of powder composition on microstructure, phase formation, and mechanical properties in laser-based powder bed fusion of tungsten carbide-cobalt. The study finds that laser energy input affects the porosity and growth of WC grains, and the addition of vanadium carbide and chromium increases the formation of additional phases and grain growth.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2022)

Add to Collection

Article Engineering, Biomedical

Effects of heat treatment on the microstructure, residual stress, and mechanical properties of Co-Cr alloy fabricated by selective laser melting

Kyung-Ho Ko et al.

Summary: The mechanical properties and residual stress of dental Co-Cr-Mo alloy are influenced by manufacturing and post-processing methods. Selective laser melting (SLM) manufacturing method produces CCM alloy with superior mechanical properties and residual stress. Heat treatment at temperatures above 950 degrees C helps reduce residual stress and increase ductility.

JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical responses of sheet-based gyroid-type triply periodic minimal surface lattice structures fabricated using selective laser melting

Cong Zhang et al.

Summary: Due to their lightweight design, high energy absorption capacity, and excellent thermal and sound insulation properties, lattice structures have great potential in various fields. In this study, a specific geometric design was used to create lattice structures, and their mechanical properties and deformation characteristics were investigated through experiments and simulations. The results showed that the stress change in the graded structure was larger during plastic deformation, and the mechanical properties could be customized by controlling the volume fraction.

MATERIALS & DESIGN (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of different substrates on the microstructure and mechanical properties of WC-12Co cemented carbide fabricated via laser melting deposition

Xiaofeng Li et al.

Summary: This study focused on analyzing the microstructure and mechanical properties of cemented carbides fabricated via LMD on different substrates. The results showed that cemented carbide formed on the WC-20Co substrate had higher density and fewer cracks and pores compared to the 45# steel substrate. The smaller grain size in the microstructure of the cemented carbide formed on the 45# steel substrate was possibly influenced by differences in liquid phase point and solid solubility between the two materials.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2022)

Add to Collection

Review Chemistry, Physical

Recent advances in Ti-6Al-4V additively manufactured by selective laser melting for biomedical implants: Prospect development

A. N. Aufa et al.

Summary: This review focused on the current issue of stress-shielding limitations in SLM Ti-6Al-4V owing to failures in load-bearing applications. The surface treatment and modification strategy that might improve the osseointegration of the implant were discussed. The corrosion resistance of SLM Ti-6Al-4V which could significantly affect antibacterial capability, improve cell adherence and apatite formation on the bone remodeling surface was also addressed.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Ultra strong and ductile eutectic high entropy alloy fabricated by selective laser melting

Fan Yang et al.

Summary: Eutectic high entropy alloys with excellent strength and ductility in a wide temperature range have important application prospects. The casting characteristics of eutectic high entropy alloys enable well manufacturability through selective laser melting. This study achieved crack-free eutectic high entropy alloy fabricated by selective laser melting for the first time, showing excellent mechanical properties in a wide temperature range from -196 degrees C to 760 degrees C.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Study on the effect of preheating temperature of SLM process on characteristics of CoCrMo alloy

Gyung Bae Bang et al.

Summary: This study investigates the effects of pre-heating temperature on the microstructure and mechanical characteristics of CoCrMo alloy specimens in selective laser melting process. Increasing the pre-heating temperature inhibits the phase transformation and results in coarse grain. However, it improves the elongation property while only minimally reducing the strength. The cooling speed increases with higher pre-heating temperature, which decreases the residual stress and improves the mechanical characteristics.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Precipitation behavior, microstructure and mechanical properties of Al-4.8Mg-0.82Sc-0.28Zr alloy fabricated by selective laser melting

Tianchun Zou et al.

Summary: In this study, the Al-4.8Mg-0.82Sc-0.28Zr alloy was fabricated by selective laser melting and its formability, microstructure, precipitation behavior, and mechanical properties were systematically investigated. The results showed that the alloy exhibited good forming quality and excellent mechanical properties under specific process parameters.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Materials Science, Ceramics

SLM printing of cermet powders: Inhomogeneity from atomic scale to microstructure

Ming Xing et al.

Summary: This study investigated the process of printing cermet powders using SLM technology through simulations and experiments. The results showed that the evolution of the metallic and ceramic phases exhibited inhomogeneity in the microstructures, leading to the presence of microstructural defects. The bonding necks between particles were mainly formed and grew during the later stage of laser heating and the early stage of solidification.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and properties of WC-12Co cemented carbide fabricated via selective electron beam melting

Jianhong Wang et al.

Summary: In this study, the microstructure, mechanical and wear properties of WC-12Co cemented carbides fabricated via selective electron beam melting were investigated. Vacuum sintering heat treatment was conducted on some of the samples, leading to the improvement of compressive strength but deterioration of wear properties.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2022)

Add to Collection

Article Chemistry, Physical

Powder densification behavior and microstructure formation mechanism of W-Ni alloy processed by selective laser melting

Qiao Zhong et al.

Summary: This study fabricated W-Ni alloy samples using selective laser melting (SLM) technology and investigated the powder densification behavior and microstructure formation mechanism. The results showed that increasing the Ni content could improve the densification degree of the W-Ni alloy samples and lead to different grain morphologies and microstructure features. Additionally, the increase of Ni content could decrease the microhardness of the samples.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Dislocation networks in gamma/gamma'-microstructures formed during selective laser melting of a Ni-base superalloy

L. Heep et al.

Summary: The dislocation network formed during selective laser melting of a Ni-base superalloy was analyzed using scanning transmission electron microscopy (STEM). It was found that the network trapped in an ordered Gamma'-phase region formed two dislocation families with pairs of anti-phase boundary (APB) coupled super partial dislocations, exhibiting unusual features such as twist character and low APB energies.

SCRIPTA MATERIALIA (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure tailoring of Ti-15Mo alloy fabricated by selective laser melting with high strength and ductility

Jian Chen et al.

Summary: The study systematically investigated the SLM of Ti-15Mo alloy, particularly focusing on densification, microstructure, and mechanical properties. The samples processed by SLM exhibit a greater combination of high tensile strength and elongation due to the retention of omega phase, high dislocation density, finer grains, twinning-induced plasticity, and changes in texture orientation.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Strengthening cemented carbides by activated nano TaC

Chong Zhao et al.

Summary: By introducing activated nano TaC, the comprehensive properties of WC-Co cemented carbides were enhanced, forming nanoscale Co-rich particles and cubic-Ta4C3 precipitates. The combined strengthening effects resulted in excellent comprehensive mechanical properties, with the rupture strength achieving the highest level reported so far among similar materials in the literature.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Subsurface faceted cracking behavior of selective laser melting Ni-based superalloy under very high cycle fatigue

Wei Li et al.

Summary: A Ni-based superalloy fabricated by selective laser melting (SLM) exhibits subsurface cracking with fisheye patterns under very high cycle fatigue (VHCF), leading to a descending S-N curve property. The subsurface failure mechanisms are related to grain size & orientation, microtexture, and crystal defects.

SCRIPTA MATERIALIA (2021)

Add to Collection

Article Engineering, Manufacturing

Effects of process parameters and scanning patterns on quality of thin-walled copper flanges manufactured by selective laser melting

Zheng-Xiong Ma et al.

Summary: This study investigated the influence of selective laser melting parameters on the forming quality of a thin-walled copper flange through an orthogonal test, revealing that better forming quality was achieved under linear scanning. Additionally, circular scanning improved surface flatness and reduced rough surface morphology height differences in the sample.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Controlling WC/Co two-phase microstructure of cemented carbides additive-manufactured by laser powder bed fusion: Effect of powder composition and post heat-treatment

Hiroyuki Ibe et al.

Summary: The study successfully controlled the WC-Co two-phase microstructures through LPBF process, with post heat-treatment eliminating defects. Addition of carbon prevented the formation of W3Co3C phase, but reduced the hardness of the samples after heat treatment.

MATERIALS & DESIGN (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation on the modelling approach for variable-density lattice structures fabricated using selective laser melting

Jun Song et al.

Summary: This study proposed a modeling approach to decrease the number of design variables in VD design, which was able to improve the performance of lightweight design based on the research on VD lattice structures manufactured using SLM.

MATERIALS & DESIGN (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Thermomechanical behaviour of WC-W2C composites at first wall in fusion conditions

E. M. Garcia-Ayala et al.

Summary: In this study, WC matrices with additions of 10, 20, and 50 vol% of tungsten dispersed by colloidal processing routes and sintered by Spark Plasma Sintering (SPS) were characterized for their microstructure and high temperature mechanical properties. The presence of metallic tungsten in the final microstructure was found to be responsible for the plastic behavior and increased toughness of the tested pieces at 1200 degrees C. The mechanical results indicated that the resistance of all materials increased with increasing operating temperature, with the composition containing 10% and 20% tungsten exhibiting the best performance.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Correlation between microstructural heterogeneity and mechanical properties of WC-Co composite additively manufactured by selective laser melting

Sujung Son et al.

Summary: This study investigates the effect of microstructural heterogeneity on mechanical properties and crack propagation in WC-Co composite additively-manufactured by selective laser melting (SLM). The research shows that this heterogeneity contributes to interrupting crack propagation and promoting further deformation.

MATERIALS LETTERS (2021)

Add to Collection

Article Optics

Simulation of temperature field and stress field of selective laser melting of multi-layer metal powder

Zhonghua Li et al.

Summary: This study investigated the temperature field and stress field of a multilayer metal powder using the point exposure scanning mode. A three-dimensional thermo-structural coupling model was established and the SLM process was simulated. The residual stress distribution on the upper surface had strong volatility, and the accuracy of the numerical simulation was verified by experimental data on the molten pool size.

OPTICS AND LASER TECHNOLOGY (2021)

Add to Collection

Article Chemistry, Physical

Effects of Different Substrates on the Formability and Densification Behaviors of Cemented Carbide Processed by Laser Powder Bed Fusion

Decheng Liu et al.

Summary: The study found that Ni200 substrates had better wettability for single tracks formation during the L-PBF process, and could ensure fewer cracks, making it an ideal choice for substrate selection.

MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of additive manufactured W-Ni-Fe-Co composite produced by selective laser melting

Hui Chen et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2020)

Add to Collection

Review Automation & Control Systems

Additive manufacturing of WC-Co hardmetals: a review

Yankun Yang et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation on plastic deformation mechanism of ultra-coarse cemented carbide based on energy analysis

Xuemei Liu et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2020)

Add to Collection

Article Engineering, Multidisciplinary

Abrasive flow machining (AFM) finishing of conformal cooling channels created by selective laser melting (SLM)

Sangil Han et al.

PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Compressive creep of coarse-grain WC-Co and WC-TaC-Co hardmetals with uniform microstructure comprising rounded WC grains

A. A. Zaitsev et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure evolution of WC-20Co cemented carbide during direct selective laser melting

Jinyang Liu et al.

POWDER METALLURGY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Development of the Structure of Cemented Carbides during Their Processing by SLM and HIP

David Bricin et al.

METALS (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Cemented carbide microstructures: a review

Jose Garcia et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2019)

Add to Collection

Article Engineering, Industrial

Influence of laser parameters and complex structural features on the bio-inspired complex thin-wall structures fabricated by selective laser melting

Kaijie Lin et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)

Add to Collection

Article Chemistry, Physical

Printability and Microstructure of Selective Laser Melting of WC/Co/Cr Powder

Sabina Luisa Campanelli et al.

MATERIALS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Additive manufacturing of WC-13%Co by selective electron beam melting: Achievements and challenges

I. Konyashin et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2019)

Add to Collection

Article Automation & Control Systems

SLM tooling for die casting with conformal cooling channels

Antonio Armillotta et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)

Add to Collection

Article Automation & Control Systems

Numerical simulation of laser-tungsten inert arc deep penetration welding between WC-Co cemented carbide and invar alloys

Pei-quan Xu et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2011)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical properties of WC/Co cemented carbide with larger WC grain size

S Okamoto et al.

MATERIALS CHARACTERIZATION (2005)

Add to Collection

© Peeref 2019-2024. All rights reserved.