☆ 4.6 Article

Prediction of the composition of surface alloys formed via pulsed melting of preliminary deposited coatings

MATERIALS CHEMISTRY AND PHYSICS (2022)

Related references

Note: Only part of the references are listed.

Article Chemistry, Physical

Synthesis and microstructure, properties characterization of Ni-Ti-Cu/Cu-Al functionally graded coating on Mg-Li alloy by laser cladding

Lipeng Jiang et al.

Summary: The Ni-Ti-Cu/Cu-Al functionally graded coating was proposed and successfully prepared on Mg-Li alloy, exhibiting excellent performance. The top-layer was unaffected by dilution and substrate evaporation, improving the corrosion and wear resistance of the alloy significantly.

APPLIED SURFACE SCIENCE (2022)

Add to Collection

Review Chemistry, Physical

Review on chromium coated zirconium alloy accident tolerant fuel cladding

Jianqiao Yang et al.

Summary: This paper reviews the oxidation, diffusion, and mechanical properties of Cr-coated Zr alloys in normal operation conditions and accident conditions of nuclear reactors, analyzes the factors that cause coating failure, and proposes questions that need to be clarified and further studied.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Chemistry, Physical

Microstructure and corrosion behavior of CeO2/FeCoNiCrMo high-entropy alloy coating prepared by laser cladding

Chen Cui et al.

Summary: FeCoNiCrMo high-entropy coatings and CeO2/FeCoNiCrMo composite coatings were successfully prepared on TC4 alloy surface using laser cladding technology. The addition of CeO2 improved the corrosion resistance of the coatings by forming a stronger passive film that inhibited pitting corrosion. HEA coatings exhibited higher microhardness and improved corrosion resistance compared to TC4 alloy.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Materials Science, Coatings & Films

Optimizing direct laser metal deposition of H13 cladding on CuBe alloy substrate

M. Pellizzari et al.

Summary: This work aims to deposit single-layer H13 tool steel cladding on a CuBe alloy substrate using DLMD. By optimizing the process parameters and substrate preheating temperature, a high-quality and dense cladding layer was successfully obtained.

SURFACE & COATINGS TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Coatings & Films

Microstructure and wear behavior of laser clad interstitial CoCrFeNi high entropy alloy coating reinforced by carbon nanotubes

Bing Han et al.

Summary: The effect of carbon nanotubes (CNTs) in reinforcing a laser clad interstitial CoCrFeNi high entropy alloy coating was investigated. The addition of CNTs enhanced the hardness and wear properties of the coating. The microstructure of the CNTs on the powder surface was well protected from damage, and the wear rate of the coating was significantly reduced. This improvement in wear performance was attributed to the solution strengthening and precipitation strengthening effects of carbon and carbides.

SURFACE & COATINGS TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Coatings & Films

Effect of oxygen in surface layers formed during sliding wear of Ni-ZrO2 coatings

Evgeny V. Kharanzhevskiy et al.

Summary: Nickel-based coatings with different content of zirconia were prepared on steel using short-pulse laser melting, and the effect of the dissolved zirconia on the tribological properties of the coatings was studied. The dissolved zirconia in the coatings influenced the resistance to oxidation and adhesion of the rubbed surfaces during severe sliding friction.

SURFACE & COATINGS TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Coatings & Films

High-temperature oxidation performance of laser-cladded amorphous TiNiSiCrCoAl high-entropy alloy coating on Ti-6Al-4V surface

Shen Li et al.

Summary: A TiNiSiCrCoAl high-entropy alloy coating was prepared on the surface of Ti-6Al-4V alloy using laser cladding technology to enhance its high-temperature oxidation performance. The coating exhibited a microstructure composed of a matrix and a sigma phase. The amorphous-structured matrix showed higher oxidation resistance compared to the FCC-structured sigma phase. The coating demonstrated significantly improved oxidation resistance at high temperatures when compared to the Ti-6Al-4V substrate.

SURFACE & COATINGS TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Coatings & Films

Effect and action mechanism of ultrasonic assistance on microstructure and mechanical performance of laser cladding 316L stainless steel coating

D. -D. Zhuang et al.

Summary: The effect and mechanism of ultrasonic vibration on the microstructure and performance of laser cladding 316L coating has been studied, showing that ultrasonic vibration can effectively improve the forming quality, wear resistance, and corrosion resistance of the cladding layer.

SURFACE & COATINGS TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Application of high current pulsed electron beam irradiation to smoothing of cold spray aluminum bronze coating

K. Ivanov et al.

Summary: The research revealed that high current pulsed electron beam irradiation can smooth the surface roughness of aluminum alloy, change the phase composition, and alter the microhardness. After HCPEBI, the free volume in the layer decreased, with fewer small pores replacing large voids, and no delamination occurred along the particles interfaces.

VACUUM (2022)

Add to Collection

Article Optics

In-situ synthesis of NiCoCrMnFe high entropy alloy coating by laser cladding

F. K. Shi et al.

Summary: In-situ synthesis of a NiCoCrMnFe high entropy alloy coating on H13 die steel through multilayer laser cladding can significantly improve the surface microhardness, wear resistance, and especially hot erosion resistance of the steel.

OPTICS AND LASER TECHNOLOGY (2022)

Add to Collection

Article Optics

Microstructure and corrosion behavior of Al-Ti-TiC-CNTs/AZ31 magnesium matrix composites prepared using laser cladding and high speed friction stir processing

Fenjun Liu et al.

Summary: Al-Ti-TiC-CNTs/AZ31 magnesium matrix composites prepared by laser cladding (LC) and high speed friction stir processing (HS-FSP) exhibit refined microstructure, improved microhardness and corrosion resistance.

OPTICS AND LASER TECHNOLOGY (2022)

Add to Collection

Review Nuclear Science & Technology

Cold spray technology in nuclear energy applications: A review of recent advances

Hwasung Yeom et al.

Summary: Cold spray technology is being explored for various applications in the nuclear energy sector, including coating deposition, near-net shape manufacturing, and component repair. The focus is on improving accident-tolerant fuel cladding, enhancing wear resistance and heat transfer, and addressing stress corrosion cracking in used fuel storage systems.

ANNALS OF NUCLEAR ENERGY (2021)

Add to Collection

Article Nuclear Science & Technology

High-energy surface processing of zirconium alloys for fuel claddings of water-cooled nuclear reactors

Mikhail Slobodyan

Summary: This review discusses recent studies on surface modification of zirconium alloys, focusing on critical understanding of achievements, misconceptions, challenges, and prospects for further improvement. It aims to fill the knowledge gap in this field by proposing the most relevant investigations in the area of sciences.

NUCLEAR ENGINEERING AND DESIGN (2021)

Add to Collection

Review Optics

Recent trends in laser cladding and surface alloying

Anas Ahmad Siddiqui et al.

Summary: Laser cladding and surface alloying techniques are employed to improve surface properties of materials, with proper selection of input parameters significantly enhancing their performance. Research in this area has attracted extensive interest due to the development of high power lasers and improved control mechanisms.

OPTICS AND LASER TECHNOLOGY (2021)

Add to Collection

Article Chemistry, Physical

The impact of high current pulses electron beam on the microstructure and surface properties of Sn/Al system

Conglin Zhang et al.

Summary: Under high current pulses electron beam (HCPEB) irradiation, surface alloying of Sn/Al system resulted in initial surface roughness increase, followed by the formation of a smooth alloying layer. The microhardness of the alloying layer increased to about 0.82 GPa after 35-pulsed samples.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Materials Science, Coatings & Films

Microstructure and transient oxidation behavior of NiCoCrAlYSiHf coating modified via high-current pulsed electron beam

Jie Cai et al.

Summary: NiCoCrAlYSiHf coatings deposited via arc ion plating technique were modified by high-current pulsed electron beam (HCPEB) irradiation with different pulses. The study shows that the remelting effects induced by HCPEB irradiation greatly influence the growth behavior of thermally grown oxides (TGO), leading to the rapid formation of a complete and dense alpha-Al2O3 layer on the coatings' surface, ensuring their protective effect.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Coatings & Films

Structure and phase states modification of AL-11SI-2CU alloy processed by ion-plasma jet and pulsed electron beam

D. Zaguliaev et al.

SURFACE & COATINGS TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

The effect of high-current pulsed electron beam on phase formation and surface properties of chromium/copper system

Conglin Zhang et al.

VACUUM (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Enhancing anti-wear and anti-corrosion performance of cold spraying aluminum coating by high current pulsed electron beam irradiation

Feng Guo et al.

VACUUM (2020)

Add to Collection

Article Instruments & Instrumentation

Variable beam entrance Faraday cup system for pulsed electron beam current profile characterization

Weijie Huo et al.

REVIEW OF SCIENTIFIC INSTRUMENTS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Synthesis of a Cr-Cu surface alloy using a low-energy high-current electron beam

Alexey Markov et al.

RESULTS IN PHYSICS (2019)

Add to Collection

Article Chemistry, Physical

Atomic structure of an amorphous Ti-Ta-based surface alloy synthesized on a TiNi substrate by an electron-beam method

Viktor O. Semin et al.

APPLIED SURFACE SCIENCE (2019)

Add to Collection

Article Instruments & Instrumentation

Surface alloying of aluminum with molybdenum by high-current pulsed electron beam

Han Xia et al.

NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION B-BEAM INTERACTIONS WITH MATERIALS AND ATOMS (2018)

Add to Collection

Article Engineering, Industrial

Processing window development for laser cladding of zirconium on zirconium alloy

Arshad Harooni et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)

Add to Collection

Review Optics

Ultrafast laser processing of materials: a review

Katherine C. Phillips et al.

ADVANCES IN OPTICS AND PHOTONICS (2015)

Add to Collection

Article Physics, Fluids & Plasmas

Formation of Surface Alloys With a Low-Energy High-Current Electron Beam for Improving High-Voltage Hold-Off of Copper Electrodes

Alexey B. Markov et al.

IEEE TRANSACTIONS ON PLASMA SCIENCE (2013)

Add to Collection

Article Chemistry, Physical

Electron beam accelerators-trends in radiation processing technology for industrial and environmental applications in Latin America and the Caribbean

Wilson A. Parejo Calvo et al.

RADIATION PHYSICS AND CHEMISTRY (2012)

Add to Collection

Article Engineering, Multidisciplinary

A P(SIC)TM-Cπ facility for the surface alloying

A. B. Markov et al.

INSTRUMENTS AND EXPERIMENTAL TECHNIQUES (2011)

Add to Collection

Article Materials Science, Coatings & Films

New metal ion and plasma surface modification methods

Alexander I. Ryabchikov et al.

SURFACE & COATINGS TECHNOLOGY (2007)

Add to Collection

Article Materials Science, Coatings & Films

Beam treatment oxidation protection of AISI H13 steel by high current pulsed electron

JX Zou et al.

SURFACE & COATINGS TECHNOLOGY (2004)

Add to Collection

Article Physics, Applied

The mechanism of increase of the thickness of the zone of thermal effect during pulse-periodic treatment of a target by an electron beam

AB Markov et al.

HIGH TEMPERATURE (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.