☆ 4.7 Article

Preparation of highly efficient and eco-friendly alumina magnetic hybrid nanosorbent from red mud: Excellent adsorption capacity towards nitrate

JOURNAL OF MOLECULAR LIQUIDS (2022)

Related references

Note: Only part of the references are listed.

Article Engineering, Chemical

Design and preparation magnetic bio-surfactant rhamnolipid-layered double hydroxide nanocomposite as an efficient and recyclable adsorbent for the removal of Rifampin from aqueous solution

Asiyeh Kheradmand et al.

Summary: In this study, a magnetic core-shell rhamnolipid (MCSR) intercalated cobalt/aluminum layered double hydroxide (LDH) was used for water remediation and rifampin (RIF) removal. The biosurfactants, including rhamnolipid (RL), demonstrated low toxicity and environmental compatibility, and promoted the removal efficiency of the adsorbent. The adsorption process was optimized by considering factors such as pH, initial RIF concentration, contact time, and adsorbent dosage. The RIF removal efficiency was found to be 96%, with a maximum adsorption capacity of 221.30 mg/g. The magnetic property of MCSR-LDH allowed for easy recovery and regeneration of the adsorbent.

SEPARATION AND PURIFICATION TECHNOLOGY (2023)

Add to Collection

Review Environmental Sciences

Strategic management of nitrate pollution from contaminated water using viable adsorbents: An economic assessment-based review with possible policy suggestions

Bhaskar Bishayee et al.

Summary: Groundwater contamination with nitrate is a critical environment issue, driving various research studies and technologies to reduce nitrate levels in water samples for safe drinking water supply. Adsorption techniques have been found to be the most suitable and efficient approach due to their low cost, simplicity, easy handling, and high removal effectiveness. Technologies like oxide-clay nanocomposite materials show promising results in effectively removing nitrate and providing cost-effective solutions for long-term water treatment operations.

JOURNAL OF ENVIRONMENTAL MANAGEMENT (2022)

Add to Collection

Article Chemistry, Applied

Ultrasound-promoted synthesis of high-porosity silica aerogels using embedded recycled PET fibers

Zahra Niazi et al.

Summary: By physically reinforcing the gel network with recycled PET fibers, the efficiency of ambient pressure drying is improved, resulting in silica aerogels with high surface area and porosity.

MICROPOROUS AND MESOPOROUS MATERIALS (2022)

Add to Collection

Review Environmental Sciences

A critical review of various adsorbents for selective removal of nitrate from water: Structure, performance and mechanism

Yong Liu et al.

Summary: This review provides a comprehensive summary of various adsorbents used for nitrate removal. It evaluates the preparation, characterization, and adsorption performance of these adsorbents, discusses the factors influencing nitrate adsorption performance, and categorizes the possible adsorption mechanisms responsible for nitrate removal.

CHEMOSPHERE (2022)

Add to Collection

Article Environmental Sciences

Valorization of sawdust by mineral acid assisted hydrothermal carbonization for the adsorptive removal of bisphenol A: A greener approach

Ragavan Chandrasekar et al.

Summary: Sawdust was valorized through acid-assisted hydrothermal carbonization and used for the removal of endocrine disruptor Bisphenol A (BPA). The addition of acid during hydrothermal carbonization improved the removal efficiency of BPA. Two different hydrochars were prepared using different feed water solutions, and the acid-assisted hydrothermal carbonized hydrochar showed better performance in BPA removal. The adsorption of BPA onto the hydrochar could be explained by the Freundlich isotherm, followed pseudo-second-order kinetics, and was exothermic and spontaneous.

CHEMOSPHERE (2022)

Add to Collection

Article Environmental Sciences

Nitrate adsorption onto surface-modified red mud in batch and fixed-bed column systems: equilibrium, kinetic, and thermodynamic studies

Ebrahim Allahkarami et al.

Summary: This research aimed to develop a low-cost adsorbent for the removal of nitrate ion from aqueous solutions. The composite material was characterized and the influential variables on nitrate adsorption were studied. Fixed-bed column experiments were conducted and the results were successfully explained using different models.

ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH (2022)

Add to Collection

Article Engineering, Chemical

Process flowsheet for extraction of Fe, Al, Ti, Sc, and Ga values from red mud

Shrey Agrawal et al.

Summary: A comprehensive process flowsheet has been developed to recover high-purity products such as alumina, silica, ferrous oxalate, titania, and Sc-Ga containing purified solution from red mud. The overall metal extraction in this proposed flowsheet is higher compared to the direct acid baking process.

MINERALS ENGINEERING (2022)

Add to Collection

Review Chemistry, Analytical

Experimental and analytical methods for testing inhibitors and fluids in water-based drilling environments

Tawfik A. Saleh

Summary: This review discusses the analysis methods used for evaluating the inhibitors and properties of drilling fluids, including various tests such as capillary suction time, bulk hardness, and linear swell meter. The review proves to be a valuable reference for researchers and the industrial sector.

TRAC-TRENDS IN ANALYTICAL CHEMISTRY (2022)

Add to Collection

Article Chemistry, Physical

Synthesis of amine-modified graphene integrated membrane as protocols for simultaneous rejection of hydrocarbons pollutants, metal ions, and salts from water

Ali Alkenani et al.

Summary: Efficient membranes synthesized by integrating amine-modified graphene have shown significant improvement in permeability and separation capacity against organic contaminants, heavy metals, and salts in water treatment.

JOURNAL OF MOLECULAR LIQUIDS (2022)

Add to Collection

Article Green & Sustainable Science & Technology

Polypyrrole complexation on biomass-derived powdered carbon for adsorptive elimination of emerging pharmaceutical contaminant Sulfamethoxazole: A comprehensive insight

Chandi Patra et al.

Summary: This study aimed to prepare a nitrogen-enriched adsorbent by modifying the surface of biomass-derived carbon with nitrogen-rich polypyrrole for the removal of antibiotic pollutants from water. The adsorbent showed efficient adsorptive interactions with the antibiotic due to strong electrostatic interactions and other interactions. The adsorbent exhibited good recyclability and effectiveness in remediating antibiotic-contaminated solution.

JOURNAL OF CLEANER PRODUCTION (2022)

Add to Collection

Article Engineering, Environmental

Fabrication of superhydrophilic/underwater superoleophobic functionalized-nanoparticles/PVDF-supported thin film composite polyamide membranes for efficient water purification

Mauliady Satria et al.

Summary: Membrane-based separation methods are essential for water treatment, and the use of polymer-inorganic and organic composite coatings on PVDF membranes can enhance separation efficiency and antifouling properties. This research provides insights into improving the performance of PVDF membranes used in water purification.

JOURNAL OF WATER PROCESS ENGINEERING (2022)

Add to Collection

Article Chemistry, Physical

Global trends in technologies and nanomaterials for removal of sulfur organic compounds: Clean energy and green environment

Tawfik A. Saleh

Summary: This review investigates various methods, adsorbents, and catalysts used for the elimination of sulfur compounds, and presents an overview of emerging technologies for ultra deep desulfurization to obtain ultra-low-sulfur fuels. The development of robust adsorbents and nano materials with ideal regeneration approaches is necessary to establish the capabilities of desulfurization processes. This review provides essential references and future directions for developing desulfurization technologies and materials for practical applications.

JOURNAL OF MOLECULAR LIQUIDS (2022)

Add to Collection

Review Energy & Fuels

Advanced trends of shale inhibitors for enhanced properties of water-based drilling fluid

Tawfik A. Saleh

Summary: Water-based mud (WBM) is an environmentally friendly drilling fluid but can cause shale swelling; additives are used to inhibit shale swelling and improve rheological and filtration properties; nanomaterials have emerged as promising alternatives for enhancing drilling fluid properties under extreme drilling conditions.

UPSTREAM OIL AND GAS TECHNOLOGY (2022)

Add to Collection

Article Engineering, Environmental

Carbon nanotube-incorporated alumina as a support for MoNi catalysts for the efficient hydrodesulfurization of thiophenes

Tawfik A. Saleh

Summary: The study showed that adding carbon nanotubes to the alumina support enhances the catalytic activity for the hydrodesulfurization reaction of dibenzothiophene in fuels, with the AlCNTMoNi catalyst demonstrating better performance and stability compared to AlMoNi.

CHEMICAL ENGINEERING JOURNAL (2021)

Add to Collection

Article Chemistry, Physical

Synthesis of amine functionalization carbon nanotube-low symmetry porphyrin derivatives conjugates toward dye and metal ions removal

Tawfik A. Saleh et al.

Summary: Carbon nanotubes were functionalized with amine groups and conjugated with prophyrine derivatives to increase active sites. Compound 3 showed better adsorption efficiency for methylene blue at different pH values, achieving high efficiency when the adsorbent dosage increased. The adsorption mechanism involved non-electrostatic and electrostatic interactions, making the material effective for simultaneous adsorption of MB and toxic metal ions.

JOURNAL OF MOLECULAR LIQUIDS (2021)

Add to Collection

Article Agricultural Engineering

Role of porous polymer carriers and iron-carbon bioreactor combined micro-electrolysis and biological denitrification in efficient removal of nitrate from wastewater under low carbon to nitrogen ratio

Jian Liu et al.

Summary: A novel bioreactor composed of porous polymer carriers and iron-carbon was established to effectively remove nitrate under short hydraulic retention times and low carbon-to-nitrogen ratios. High-throughput sequencing revealed that Zoogloea sp. L2 was the dominant strain responsible for nitrate removal in the bioreactor.

BIORESOURCE TECHNOLOGY (2021)

Add to Collection

Review Environmental Sciences

Various electron donors for biological nitrate removal: A review

Yunmeng Pang et al.

Summary: This paper discusses the issue of nitrate pollution in water and wastewater, as well as the use of various electron donors for biological denitrification. Depending on the types of electron donors, denitrification can be classified into heterotrophic and autotrophic denitrification.

SCIENCE OF THE TOTAL ENVIRONMENT (2021)

Add to Collection

Review Environmental Sciences

Recent developments in layer-by-layer assembled systems application in water purification

Claudiu-Augustin Ghiorghita et al.

Summary: Electrostatically-based layer-by-layer (LbL) assembly is a versatile surface functionalization technique that allows the construction of complex three-dimensional architectures on various materials, with promising applications in water purification. The main strategies in this field include enhancing the barrier properties of separation membranes and constructing core-shell organic/inorganic sorbents. Recent achievements and studies on the economic aspects of using LbL assemblies for water purification suggest possible development of economically-viable materials for this application in the future.

CHEMOSPHERE (2021)

Add to Collection

Article Biotechnology & Applied Microbiology

Protocols for synthesis of nanomaterials, polymers, and green materials as adsorbents for water treatment technologies

Tawfik A. Saleh

Summary: Water pollution caused by various pollutants is a critical global issue, and the development of organized protocols and procedures for the synthesis of new adsorbent materials is essential for addressing wastewater treatment challenges.

ENVIRONMENTAL TECHNOLOGY & INNOVATION (2021)

Add to Collection

Review Engineering, Chemical

Evaluation of red mud as a polymetallic source-A review

Shrey Agrawal et al.

Summary: Red mud as an industrial waste generated during alumina production poses environmental risks and high disposal costs, prompting the utilization of valuable minerals from it. Recovering metallic values from red mud can significantly improve process efficiency, reduce industrial liability, and minimize waste generation, offering potential strategic advantages for resource-deficient nations.

MINERALS ENGINEERING (2021)

Add to Collection

Article Biotechnology & Applied Microbiology

Pilot-scale valorization of hazardous aluminum dross into γ-Al2O3 nanoadsorbent for efficient removal of fluoride

Mostafa Mahinroosta et al.

Summary: This study focused on valorizing secondary aluminum dross into gamma-aluminum oxide (γ-Al2O3) through a pilot-scale extraction system. The obtained γ-Al2O3 exhibited good fluoride adsorption performance, even after multiple regenerations, indicating its potential for practical applications in fluoride removal from water.

ENVIRONMENTAL TECHNOLOGY & INNOVATION (2021)

Add to Collection

Article Engineering, Environmental

Investigation of chromate and nitrate removal by adsorption at the surface of an amine-modified cocoa shell adsorbent

Patrick Nkuigue Fotsing et al.

Summary: The study demonstrated the successful adsorption of nitrate and chromium ions from contaminated aqueous solutions onto functionalized cocoa shell via chemical grafting. The resulting adsorbent, ECAB-APTES-HCl, showed high removal efficiency for both ions, fitting well with Freundlich and Langmuir isotherms and a pseudo-second order model. Desorption studies revealed effective recovery of the ions in a short period of time, offering a promising method for heavy metal removal from water without energy constraints.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2021)

Add to Collection

Article Chemistry, Analytical

Enhanced adsorption of congo red using cationic surfactant functionalized zeolite particles

Reza Nodehi et al.

MICROCHEMICAL JOURNAL (2020)

Add to Collection

Article Chemistry, Physical

Synergistic effect of electrostatic adsorption and ion exchange for efficient removal of nitrate

Hongchang He et al.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2020)

Add to Collection

Article Engineering, Chemical

Equilibrium data and its analysis with the Freundlich model in the adsorption of arsenic(V) on granular ferric hydroxide

Kenneth Walsh et al.

SEPARATION AND PURIFICATION TECHNOLOGY (2020)

Add to Collection

Article Chemistry, Physical

A novel red mud adsorbent for phosphorus and diclofenac removal from wastewater

Xin Li et al.

JOURNAL OF MOLECULAR LIQUIDS (2020)

Add to Collection

Article Environmental Sciences

Chemical removal and selectivity reduction of nitrate from water by (nano) zero-valent iron/activated carbon micro-electrolysis

Ningfan Song et al.

CHEMOSPHERE (2020)

Add to Collection

Review Environmental Sciences

Living in polluted waters: A meta-analysis of the effects of nitrate and interactions with other environmental stressors on freshwater taxa

Daniel F. Gomez Isaza et al.

ENVIRONMENTAL POLLUTION (2020)

Add to Collection

Article Biotechnology & Applied Microbiology

Nanomaterials: Classification, properties, and environmental toxicities

Tawfik A. Saleh

ENVIRONMENTAL TECHNOLOGY & INNOVATION (2020)

Add to Collection

Review Environmental Sciences

A review on the potential uses of red mud as amendment for pollution control in environmental media

Mehwish Taneez et al.

ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH (2019)

Add to Collection

Article Biochemistry & Molecular Biology

Synthesis and characterization of metal loaded chitosan-alginate biopolymeric hybrid beads for the efficient removal of phosphate and nitrate ions from aqueous solution

Perumal Karthikeyan et al.

INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES (2019)

Add to Collection

Article Green & Sustainable Science & Technology

Solid waste management: Scope and the challenge of sustainability

Subhasish Das et al.

JOURNAL OF CLEANER PRODUCTION (2019)

Add to Collection

Article Engineering, Environmental

A green and facile production of catalysts from waste red mud for the one-pot synthesis of glycerol carbonate from glycerol

Bikashbindu Das et al.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2019)

Add to Collection

Article Engineering, Environmental

Novel bimetallic catalyst supported by red mud for enhanced nitrate reduction

Shanawar Hamid et al.

CHEMICAL ENGINEERING JOURNAL (2018)

Add to Collection

Article Environmental Sciences

Determination of point of zero charge of natural organic materials

Elisee Nsimba Bakatula et al.

ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH (2018)

Add to Collection

Article Engineering, Environmental

Preparation of high surface area activated carbon from waste-biomass of sunflower piths: Kinetics and equilibrium studies on the dye removal

Mustafa Baysal et al.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2018)

Add to Collection

Review Engineering, Environmental

Strategies for Nitrate removal from aqueous environment using Nanotechnology: A Review

Sanjiv Tyagi et al.

JOURNAL OF WATER PROCESS ENGINEERING (2018)

Add to Collection

Article Chemistry, Physical

Adsorption of nitrate onto anionic bio-graphene nanosheet from aqueous solutions: Isotherm and kinetic study

Seid Kamal Ghadiri et al.

JOURNAL OF MOLECULAR LIQUIDS (2017)

Add to Collection

Article Engineering, Chemical

Insight into the adsorption kinetics models for the removal of contaminants from aqueous solutions

K. L. Tan et al.

JOURNAL OF THE TAIWAN INSTITUTE OF CHEMICAL ENGINEERS (2017)

Add to Collection

Article Environmental Sciences

Characteristics of Nitrate Removal from Aqueous Solution by Modified Steel Slag

Liyun Yang et al.

WATER (2017)

Add to Collection

Article Chemistry, Physical

Evaluation of natural and cationic surfactant modified pumice for congo red removal in batch mode: Kinetic, equilibrium, and thermodynamic studies

Hadi Shayesteh et al.

JOURNAL OF MOLECULAR LIQUIDS (2016)

Add to Collection

Article Chemistry, Multidisciplinary

Equilibrium, kinetics and thermodynamic parameters for adsorptive removal of dye Basic Blue 9 by ground nut shells and Eichhornia

Sumanjit et al.

ARABIAN JOURNAL OF CHEMISTRY (2016)

Add to Collection

Article Engineering, Environmental

Adsorption studies for the removal of nitrate using chitosan/PEG and chitosan/PVA polymer composites

A. Rajeswari et al.

JOURNAL OF WATER PROCESS ENGINEERING (2016)

Add to Collection

Article Environmental Sciences

Isotherm, kinetic, and thermodynamic studies on Hg(II) adsorption from aqueous solution by silica- multiwall carbon nanotubes

Tawfik A. Saleh

ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH (2015)

Add to Collection

Article Chemistry, Physical

Physical adsorption characterization of nanoporous materials: progress and challenges

Matthias Thommes et al.

ADSORPTION-JOURNAL OF THE INTERNATIONAL ADSORPTION SOCIETY (2014)

Add to Collection

Article Chemistry, Multidisciplinary

Equilibrium Isotherm Studies of Adsorption of Pigments Extracted from Kuduk-kuduk (Melastoma malabathricum L.) Pulp onto TiO2 Nanoparticles

N. T. R. N. Kumara et al.

JOURNAL OF CHEMISTRY (2014)

Add to Collection

Review Environmental Sciences

Enhanced removal of nitrate from water using surface modification of adsorbents - A review

Paripurnanda Loganathan et al.

JOURNAL OF ENVIRONMENTAL MANAGEMENT (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Synthesis and characterization of Fe3O4 nanoparticles coated with fucan polysaccharides

V. A. J. Silva et al.

JOURNAL OF MAGNETISM AND MAGNETIC MATERIALS (2013)

Add to Collection

Article Chemistry, Physical

Efficient sorbents based on magnetite coated with siliceous hybrid shells for removal of mercury ions

Daniela S. Tavares et al.

JOURNAL OF MATERIALS CHEMISTRY A (2013)

Add to Collection

Article Environmental Sciences

Carbonised red mud - A new water treatment product made from a waste material

I. D. Pulford et al.

JOURNAL OF ENVIRONMENTAL MANAGEMENT (2012)

Add to Collection

Article Chemistry, Physical

The influence of treatment temperature on the acidity of MWCNT oxidized by HNO3 or a mixture of HNO3/H2SO4

Tawfik A. Saleh

APPLIED SURFACE SCIENCE (2011)

Add to Collection

Review Engineering, Environmental

A review of emerging adsorbents for nitrate removal from water

Amit Bhatnagar et al.

CHEMICAL ENGINEERING JOURNAL (2011)

Add to Collection

Article Geosciences, Multidisciplinary

Enhanced Reduction of Nitrate in Groundwater by Zero-valent Iron with Activated Red Mud

Dong-Wan Cho et al.

GEOSYSTEM ENGINEERING (2011)

Add to Collection

Article Engineering, Environmental

Nitrate removal from water by nano-alumina: Characterization and sorption studies

Amit Bhatnagar et al.

CHEMICAL ENGINEERING JOURNAL (2010)

Add to Collection

Review Engineering, Environmental

Insights into the modeling of adsorption isotherm systems

K. Y. Foo et al.

CHEMICAL ENGINEERING JOURNAL (2010)

Add to Collection

Article Engineering, Environmental

Adsorption kinetic character of copper ions onto a modified chitosan transparent thin membrane from aqueous solution

Zihong Cheng et al.

JOURNAL OF HAZARDOUS MATERIALS (2010)

Add to Collection

Article Chemistry, Applied

Batch-wise nitrate removal from water on a surfactant-modified zeolite

Joachim Schick et al.

MICROPOROUS AND MESOPOROUS MATERIALS (2010)

Add to Collection

Article Engineering, Environmental

Initial behavior of intraparticle diffusion model used in the description of adsorption kinetics

Feng-Chin Wu et al.

CHEMICAL ENGINEERING JOURNAL (2009)

Add to Collection

Article Chemistry, Physical

Fluoride adsorption onto activated alumina: Modeling the effects of pH and some competing ions

Yulin Tang et al.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2009)

Add to Collection

Article Environmental Sciences

Influence of operating conditions on the removal of Cu, Zn, Cd and Pb ions from wastewater by adsorption

N. T. Abdel-Ghani et al.

INTERNATIONAL JOURNAL OF ENVIRONMENTAL SCIENCE AND TECHNOLOGY (2007)

Add to Collection

Article Engineering, Chemical

Removal of nitrate from aqueous solution by using red mud

Yunus Cengeloglu et al.

SEPARATION AND PURIFICATION TECHNOLOGY (2006)

Add to Collection

Article Materials Science, Multidisciplinary

Fluorescence spectroscopic study of the phase transformation of γ-Al2O3 at high temperatures

MF Luo et al.

PHYSICA STATUS SOLIDI A-APPLICATIONS AND MATERIALS SCIENCE (2006)

Add to Collection

Article Engineering, Chemical

Removal of pyridine from aqueous solution by adsorption on bagasse fly ash

Dilip H. Lataye et al.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2006)

Add to Collection

Article Engineering, Environmental

Nitrate removal from aqueous solution by adsorption onto various materials

N Öztürk et al.

JOURNAL OF HAZARDOUS MATERIALS (2004)

Add to Collection

Article Engineering, Environmental

Process development for the removal of lead and chromium from aqueous solutions using red mud - an aluminium industry waste

VK Gupta et al.

WATER RESEARCH (2001)

Add to Collection

© Peeref 2019-2024. All rights reserved.