Related references
Note: Only part of the references are listed.Microstructure Evolution and Tempering Transformation Kinetics in a Secondary Hardened M50 Steel Subjected to Cold Ring Rolling
Feng Wang et al.
ISIJ INTERNATIONAL (2021)
Experimental investigation and finite-element modeling of the short-time induction quench-and-temper process of AISI 4140
D. Kaiser et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)
Comparative micromechanics assessment of high-carbon martensite/bainite bearing steel microstructures using in-situ synchrotron X-ray diffraction
D. Foster et al.
MATERIALIA (2020)
Early stages of cementite precipitation during tempering of 1C-1Cr martensitic steel
Ziyong Hou et al.
JOURNAL OF MATERIALS SCIENCE (2019)
Effects of rare earth elements on inclusions and impact toughness of high-carbon chromium bearing steel
Chaoyun Yang et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)
Effect of Prior Cold Deformation on the Stability of Retained Austenite in GCr15 Bearing Steel
Feng Wang et al.
ACTA METALLURGICA SINICA-ENGLISH LETTERS (2019)
On Tetragonality of the Martensite Crystal Lattice in Steels
V. A. Lobodyuk et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2019)
Transformation from non-isothermal to isothermal tempering of steel based on isoconversional method
Qinglong Liu et al.
JOURNAL OF MATERIALS SCIENCE (2018)
Numerical simulation on induction heat treatment process of a shaft part: Involving induction hardening and tempering
Daming Tong et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
Unit cell dilation technique for analyzing dilatometry data in microalloyed steels
Nasseh Khodaie et al.
MATERIALS CHARACTERIZATION (2018)
Stability of retained austenite in martensitic high carbon steels. Part I: Thermal stability
Wen Cui et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Nonequilibrium thermodynamic modeling of carbon partitioning in quench and partition (Q&P) steel
Amit K. Behera et al.
SCRIPTA MATERIALIA (2018)
A simple and precise differential incremental isoconversional method to kinetic analysis of heterogeneous processes under arbitrary temperature programs
Petru Budrugeac
THERMOCHIMICA ACTA (2018)
A dilatometric study on the influence of compressive stresses on the tempering of martensitic AISI 4140 steel - Evidence of transformation induced plasticity during cementite precipitation
D. Kaiser et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Phase evolution and carbon redistribution during continuous tempering of martensite studied with high resolution techniques
Annika Vieweg et al.
MATERIALS & DESIGN (2017)
Thermal Stability of Retained Austenite in High-carbon Steels during Cryogenic and Tempering Treatments
Xun Qiao et al.
ISIJ INTERNATIONAL (2016)
Ageing of 100Cr6 steel: synchrotron X-ray diffraction and dimensional analysis investigation
V. Lejay et al.
MATERIALS SCIENCE AND TECHNOLOGY (2016)
A first-principles study of cementite (Fe3C) and its alloyed counterparts: Structural properties, stability, and electronic structure
V. I. Razumovskiy et al.
COMPUTATIONAL MATERIALS SCIENCE (2015)
Carbon diffusion in carbon-supersaturated ferrite and austenite
J. Cermak et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2014)
Influence of deep cryogenic treatment on the thermal decomposition of Fe-C martensite
M. Preciado et al.
JOURNAL OF MATERIALS SCIENCE (2014)
Atomic-scale investigation of ε and θ precipitates in bainite in 100Cr6 bearing steel by atom probe tomography and ab initio calculations
W. Song et al.
ACTA MATERIALIA (2013)
The ε → η → θ transition in 100Cr6 and its effect on mechanical properties
A. T. W. Barrow et al.
ACTA MATERIALIA (2012)
Isoconversional analysis of solid-state transformations A critical review. Part III. Isothermal and non isothermal predictions
J. Farjas et al.
JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2012)
Rolling bearing applications: some trends in materials and heat treatments
E. Tonicello et al.
MATERIALS SCIENCE AND TECHNOLOGY (2012)
ICTAC Kinetics Committee recommendations for performing kinetic computations on thermal analysis data
Sergey Vyazovkin et al.
THERMOCHIMICA ACTA (2011)
Separation of overlapping retained austenite decomposition and cementite precipitation reactions during tempering of martensitic steel by means of thermal analysis
S. Primig et al.
THERMOCHIMICA ACTA (2011)
ε-Carbide in alloy steels: First-principles assessment
Jae Hoon Jang et al.
SCRIPTA MATERIALIA (2010)
Microstructural evolution of martensitic 100Cr6 bearing steel during tempering: From thermoelectric power measurements to the prediction of dimensional changes
Michel Perez et al.
ACTA MATERIALIA (2009)
Microstructural and Dilatational Changes during Tempering and Tempering Kinetics in Martensitic Medium-Carbon Steel
Minsu Jung et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2009)
A Model for Converting Dilatometric Strain Measurements to the Fraction of Phase Formed during the Transformation of Austenite to Martensite in Powder Metallurgy Steels
Virendra S. Warke et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2009)
Characterization of the microstructure obtained by the quenching and partitioning process in a low-carbon steel
M. J. Santofimia et al.
MATERIALS CHARACTERIZATION (2008)
Evolution and thermal stability of retained austenite in SAE 52100 bainitic steel
Natalia Luzginova et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2007)
A study of the carbon distribution in retained austenite
C. P. Scott et al.
SCRIPTA MATERIALIA (2007)
Cementite dissolution at 860°C in an Fe-Cr-C steel
L. Zhao et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2006)
Modelling of precipitation of carbides during tempering of martensite
Y Wang et al.
JOURNAL DE PHYSIQUE IV (2004)
Decomposition of iron-based martensite. A kinetic analysis by means of differential scanning calorimetry and dilatometry
PV Morra et al.
JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2001)
Share Paper
