Related references
Note: Only part of the references are listed.
Article
Engineering, Chemical
Noureddine Lebaz et al.
Summary: This work investigates droplet breakage during continuous emulsification in static mixers, introducing a full spectrum-based model within a population balance model to describe the time evolution of droplet size distribution. The model, tested against experimental data, shows predictive capabilities and improved computational efficiency compared to CFD simulations. The full spectrum-based model requires knowledge of mean turbulent kinetic energy and energy dissipation rate, which can be estimated through pressure drop measurements for rapid implementation.
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
(2022)
Article
Engineering, Chemical
Raviraju Vysyaraju et al.
Summary: Hydrocyclones provide an efficient environment for particle classification or phase separation, but face the performance limitation of fine particle bypassing. A novel design modification involving fitting thin concentric rings to the cylindro-conical section can mitigate this limitation and achieve better fine particle separation.
Article
Engineering, Chemical
Xueke Li et al.
Summary: This article summarizes the development and issues of gas desulfurization technology, discusses key theories and optimal parameters in the desulfurization process, and enhances the added value of desulfurization technology through studying the recycling of desulfurization products.
SEPARATION AND PURIFICATION TECHNOLOGY
(2022)
Article
Engineering, Chemical
Myung Soo Kang et al.
Summary: Coal is expected to remain a primary energy source due to its production stability and cost-effectiveness. However, the emissions of SO2 and NOx during coal combustion have raised serious environmental concerns. This study successfully reduced the concentrations of SO2 and NOx using ozone and ammonia, with higher SO2 concentrations leading to higher NOx removal efficiency.
SEPARATION AND PURIFICATION TECHNOLOGY
(2022)
Article
Engineering, Environmental
Se Won Jeon et al.
Summary: In this study, a hybrid catalyst was introduced, which exhibited better stability and sulfur tolerance during SO2 aging. The hybrid catalyst achieved the direct migration of ammonium bisulfate from the vanadia domain to the alumina domain through physical contact, rather than gas-phase adsorption. The surface properties of the mixed alumina played an important role in its affinity to ammonium bisulfate and reusability.
CHEMICAL ENGINEERING JOURNAL
(2022)
Article
Energy & Fuels
Xinhong Dong et al.
Summary: Developing novel AOP for flue gas denitrification is a hot topic in air pollution control. This study demonstrates for the first time that alcohol species can be used in AOP process to synergistically remove NO with O-2 under UV185 light. Isopropanol and ethanol can achieve NO removal rates of 95.6% and 87.5% respectively.
Article
Engineering, Chemical
Sijie Dong et al.
Summary: This study investigates the energy loss mechanism in gas cyclones and explores the effects of inlet velocity, wall roughness, and particle loading ratio on energy loss. The findings reveal the presence of high energy loss regions in gas cyclones and identify the different impacts of inlet velocity, wall roughness, and particle loading ratio on energy loss.
Article
Engineering, Chemical
Li Cai et al.
Summary: This study proposed a simplified desulfurization model based on the two-film theory for semi-dry circulating fluidized bed flue gas desulfurization (CFB-FGD). By simulating the effects of different parameters on desulfurization efficiency and applying response surface methodology (RSM), the optimal operating parameters were determined, resulting in a desulfurization efficiency of 99.69%.
Article
Engineering, Chemical
Jiwei Wu et al.
Summary: This paper discusses a cyclone oil desorption technology, which uses the self-rotation of particles to achieve the desorption of oil phase from the pores of cuttings. The experiments show that when the particle self-rotation speed is faster than the critical self-rotation speed, the oil phase in the particle pores can be desorbed.
SEPARATION AND PURIFICATION TECHNOLOGY
(2022)
Article
Engineering, Chemical
Casper S. Svith et al.
Summary: The Selective Non-Catalytic Reduction (SNCR) process was investigated in a bench scale cyclone reactor through experiments and modelling. The results showed that high NO reduction and NH3/NO ratios can be achieved under specific operating conditions. The models were able to qualitatively predict the trends of NO reduction and ammonia slip, although the ammonia slip was over-predicted in most cases. Temperature and kinetics had a significant impact on the outlet concentrations. The compartment model accurately reproduced the cyclone's NO concentration profiles and provided a qualitative prediction of the NH3 profiles. The choice of bypass fractions had a significant influence on the ammonia profiles.
CHEMICAL ENGINEERING RESEARCH & DESIGN
(2022)
Article
Engineering, Chemical
Wen Jin et al.
Summary: Impinging jet atomization is a new approach in drug delivery for inhalation therapy. Numerical simulation is used to better understand the dynamics of the impinging jet. A computational fluid dynamics model was used to simulate the atomization process, which couples the Volume of Fluid method, Discrete Phase Model, and Adaptive Mesh Refinement. The study reveals the influence of the flow field inside the nozzle on the atomization characteristics.
Article
Environmental Sciences
Yiqi Guo et al.
Summary: Air pollution, caused by pollutants such as nitrogen oxide (NOX) and sulfur dioxide (SO2), has a significant impact on human health and the environment. The textile industry, which emits large quantities of NOX and SO2 during production, is facing enormous environmental pressure. This study proposes a Chemical Footprint (ChF) assessment method using the USEtox model to evaluate NOX and SO2 emissions from textile production. The results demonstrate that NOX emissions in Zhejiang's textile industry cause approximately eight times more ChF than SO2 emissions. The textile manufacturing sector has the largest ChF, accounting for 73% of the total ChF caused by NOX and SO2 emissions.
SCIENCE OF THE TOTAL ENVIRONMENT
(2022)
Article
Energy & Fuels
Jianlong Chang et al.
Summary: This study investigates the primary atomization of liquid transverse jets in subsonic crossflow using Large Eddy Simulation (LES) and interface tracking methods. The results show that the shear action of gas and liquid leads to the generation of Kelvin-Helmholtz (KH) unstable wave and Rayleigh-Taylor (RT) unstable wave, where the KH surface wave dominates the surface breaking of the jet column and the RT surface wave dominates the fracture of the jet column.
Article
Energy & Fuels
Afzal Husain Khan et al.
ENERGY CONVERSION AND MANAGEMENT
(2022)
Article
Energy & Fuels
Jiwei Wu et al.
Summary: This study investigates the physicochemical properties of oil-based mud cuttings before and after treatment using cyclone oil desorption technology. The technology effectively reduces oil content, increases carbonization and hydrophilicity, and decreases average particle size. However, heavy metal content still exceeds standard levels. The fuzzy comprehensive evaluation indicates that cyclone oil desorption technology has a promising application prospect.
Article
Environmental Sciences
Natalia Gemza et al.
Summary: This study presents the long-term effects of a full-scale hydrocyclone unit on sedimentation, treatment efficiency, and sludge morphology in a continuous flow system. The research focuses on understanding the mechanisms of sludge behavior within the system. The findings show that temperature variations and overgrowth of filamentous bacteria can impact sedimentation efficiency, and sludge separated by the hydrocyclone exhibits higher settling velocity and a more compact, spherical morphology.
SCIENCE OF THE TOTAL ENVIRONMENT
(2022)
Article
Energy & Fuels
Zhaomin Lv et al.
Summary: This study investigated the impact of higher preheating temperature on NOx emissions and combustion characteristics. Findings demonstrated that higher preheating temperature could reduce NO emissions and enhance combustion efficiency, particularly in fuel-rich conditions. Additionally, the study highlighted the critical role of stoichiometry parameters in influencing NOx emissions during combustion.
Article
Energy & Fuels
Lin Cui et al.
Summary: Limestone-gypsum wet flue gas desulfurization (WFGD) is the most effective desulfurization technique. By coupling WFGD with condensation desulfurization using a condensing heat exchanger (CHE), significant energy savings can be achieved while improving desulfurization efficiency.
Review
Environmental Sciences
Meng Si et al.
Summary: This paper summarizes the efficiency, effect factors, and advantages and disadvantages of various NO oxidation methods for removing NO pollutants from flue gas. It also provides suggestions for future research directions in NO oxidation.
JOURNAL OF ENVIRONMENTAL SCIENCES
(2021)
Article
Engineering, Chemical
Yuge Yao et al.
Summary: The length of the inlet duct may affect the gas flow field and performance of a cyclone separator, with longer ducts leading to higher tangential gas velocity but lower pressure drop and separation efficiency. Expansion loss at the inlet and friction loss inside the cyclone body contribute to the reduction of pressure drop as the inlet duct length increases, with minimal effect once the length is 1.5 times the cylinder diameter.
Article
Engineering, Chemical
Feng Li et al.
Summary: A novel hydrocyclone with bi-symmetrical involue inlet, thick-wall overflow pipes and conical segment structure was designed and compared with other hydrocyclones. Numerical analysis showed that the flow field in the novel hydrocyclone is more stable, resulting in a significant increase in impurity removal efficiency. The tangential velocity, the axial velocity and the pressure also increased significantly when using the novel hydrocyclone, leading to a reduced number of dislocated particles and enhanced recovery ratio of fine particles.
Article
Engineering, Chemical
Liwang Wang et al.
Summary: The study found that lowering the absorption solution temperature and increasing the liquid phase velocity can enhance the removal effect of CS2, but simply increasing the mass transfer coefficient does not guarantee a higher absorption efficiency. Experimental verification showed that the highest efficiency of 94.05% was obtained at an intake air flow rate of 18 l/min. The gas cyclone-liquid jet separator has been successfully applied for the first time to remove CS2 from waste gas from the rubber industry, significantly reducing treatment costs and showing excellent application prospects.
SEPARATION AND PURIFICATION TECHNOLOGY
(2021)
Article
Engineering, Chemical
Jiaqiang Jing et al.
Summary: Sand production is common in offshore heavy oil production, posing risks to production safety. The high viscosity of heavy oil makes the separation of sand particles challenging. This study proposes a desanding scheme that combines viscosity reduction through water blending and hydrocyclone separation, focusing on the characteristics of hydrocyclone separation in heavy oil desanding.
SEPARATION AND PURIFICATION TECHNOLOGY
(2021)
Article
Engineering, Chemical
Yanni Chi et al.
Summary: The study investigated the flow characteristics of a liquid-liquid cyclone reactor using computational fluid dynamics and confirmed the correctness of the model through experiments. The research focused on the deformation and breakage process of droplets, revealing that droplet breakage mainly occurs in the velocity boundary layer.
CHINESE JOURNAL OF CHEMICAL ENGINEERING
(2021)
Article
Engineering, Chemical
Nihan Uygur Babaoglu et al.
Summary: The study showed that the inlet cross-sectional shape of a gas cyclone has a significant impact on the flow pattern, pressure drop, and cut-off diameter. Rectangle-shaped inlets generate higher tangential velocities, while different shapes of inlets result in different pressure drops.
Review
Engineering, Environmental
Rong Chen et al.
Summary: The paper provides a timely review of simultaneous de-SO2 and de-NOx methods, categorizing them into four pathways and systematically reviewing the removal process, basic mechanism, and kinetics of each pathway. The main challenges and potential breakthroughs in developing novel methods are critically discussed, providing a roadmap for prospective research activities. This review offers deeper insights into understanding the mechanisms of de-SO2 and de-NOx, aiming to develop innovative simultaneous removal methods or enhance the efficiency of available abatement methods.
CHEMICAL ENGINEERING JOURNAL
(2021)
Article
Energy & Fuels
Xiong Xiaohe et al.
Summary: Preheating combustion technology is effective in reducing NOx emissions, but not effective for reducing SO2. Higher preheating temperatures lead to greater reductions in NOx emissions. Under fuel-rich conditions, while NO decreases significantly, there is an increase in NO2, indicating the need to pay attention to both NO and NO2 for achieving ultra-low emission levels.
JOURNAL OF THE ENERGY INSTITUTE
(2021)
Article
Engineering, Environmental
Myung Soo Kang et al.
CHEMICAL ENGINEERING JOURNAL
(2020)
Article
Environmental Sciences
Bing Liu et al.
SCIENCE OF THE TOTAL ENVIRONMENT
(2020)
Article
Energy & Fuels
Liang Ma et al.
CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION
(2020)
Article
Engineering, Chemical
Baowei Wang et al.
CHINESE JOURNAL OF CHEMICAL ENGINEERING
(2020)
Article
Engineering, Chemical
Liang Ma et al.
ASIA-PACIFIC JOURNAL OF CHEMICAL ENGINEERING
(2020)
Article
Engineering, Environmental
Yujin Hwang et al.
JOURNAL OF HAZARDOUS MATERIALS
(2020)
Article
Engineering, Chemical
Chunlai Liu et al.
CHINESE JOURNAL OF CHEMICAL ENGINEERING
(2019)
Article
Green & Sustainable Science & Technology
Wenqiang Sun et al.
JOURNAL OF CLEANER PRODUCTION
(2019)
Article
Environmental Sciences
Shuang Zhao et al.
ENVIRONMENTAL POLLUTION
(2018)
Article
Energy & Fuels
Shaoping Cui et al.
Article
Green & Sustainable Science & Technology
Peng-Bo Fu et al.
JOURNAL OF CLEANER PRODUCTION
(2018)
Article
Mechanics
Y. Xia et al.
INTERNATIONAL JOURNAL OF MULTIPHASE FLOW
(2017)
Article
Metallurgy & Metallurgical Engineering
Bo Tang et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA
(2017)
Article
Environmental Sciences
Yi-Mou Wang et al.
AEROSOL AND AIR QUALITY RESEARCH
(2017)
Article
Energy & Fuels
Yi Zhao et al.
Article
Engineering, Environmental
Sajeev Philip et al.
ENVIRONMENTAL SCIENCE & TECHNOLOGY
(2014)
Article
Engineering, Environmental
Yi Zhao et al.
CHEMICAL ENGINEERING JOURNAL
(2010)
Article
Engineering, Chemical
Nick D. Hutson et al.
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
(2008)
Article
Engineering, Environmental
C. Arden Pope et al.
JOURNAL OF THE AIR & WASTE MANAGEMENT ASSOCIATION
(2006)
