Material removal mechanism and microstructure fabrication of GDP during micro-milling

Article Automation & Control Systems

Machinability investigation of polymer/GNP nanocomposites in micro-milling

Guoyu Fu et al.

Summary: This study investigated the influence of adding GNP nanoparticles to polymer materials on micro-milling performance, and found that this addition changes the slot edge formation mode.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2022)

Add to Collection

Article Green & Sustainable Science & Technology

Material removal energy in ultraprecision machining of micro-lens arrays on single crystal silicon by slow tool servo

Zejia Zhao et al.

Summary: This paper investigates the evolution of material removal energy in ultraprecision machining and finds that the total material removal energy decreases with increasing feedrate, but the maximum material removal energy increases. The study also discusses the differences in material removal energy in different regions and the formation mechanism and effects of cleavage fracture.

JOURNAL OF CLEANER PRODUCTION (2022)

Add to Collection

Article Engineering, Mechanical

Material removal and surface generation in longitudinal-torsional ultrasonic assisted milling

Shaoqing Qin et al.

Summary: This paper introduces the Longitudinal-Torsional Ultrasonic Assisted Milling (LTUAM) method for machining high-strength titanium alloy, which can reduce cutting force and enhance surface micro-hardness.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2022)

Add to Collection

Article Optics

Morphology evolution mechanisms and localized structural modification of repaired sites on fused silica optics processed by CO2 laser rapid ablation mitigation

Chao Tan et al.

Summary: The research found that a fixed depth morphology was formed starting from the third track's laser scanning during processing of fused silica by pulsed laser, with uneven concave-convex features at the bottom. The processing angle decreased as trajectory indentation increased, and the thickness of the heat-affected zone was proportional to the laser pulse width.

OPTICS AND LASER TECHNOLOGY (2022)

Add to Collection

Article Optics

Tribological performance of micro textured surface machined by Nd:YAG laser with different incident angle

Yang Lu et al.

Summary: This study investigates the fabrication of linear micro textures on cemented carbide surfaces using Nd:YAG laser at different incident angles. The results show that decreasing the incident angle reduces the depth of micro textures, laser machining temperature, and residual compressive stress. It also increases the width of the micro textures and surface roughness. The micro textured samples demonstrate improved friction performance, with the TS-60 samples showing the best results, reducing the wear rate and average coefficient of friction by approximately 71.1% and 63.2%, respectively.

OPTICS AND LASER TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Characterization & Testing

Influence of sliding velocity on microscratch response of carbohydrate polymers by Berkovich indenter

Ming Liu et al.

Summary: Microscratch tests were conducted on polyamide (PA) and polypropylene (PP) to investigate the influence of sliding velocity on the microscratch response of carbohydrate polymers. It was found that both penetration depth and residual depth decrease nonlinearly with increasing sliding velocity, while elastic deformation dominates the total deformation during scratching. Residual scratch grooves, scratch friction coefficient, and lateral force under different sliding velocities can reveal the different friction mechanisms of PA and PP.

POLYMER TESTING (2022)

Add to Collection

Article Engineering, Manufacturing

Investigation of chip formation, cutting force and surface roughness during orthogonal cutting of polytetrafluoroethylene

Zhi Cui et al.

Summary: This study investigated the cutting performance of Polytetrafluoroethylene (PTFE) using orthogonal cutting experiments. Chip formation, cutting force, and surface quality were used to evaluate the influence of cutting parameters on cutting performance. The results showed that cutting depth had the most significant effect on cutting force, while cutting speed had the most obvious effect on surface roughness. An empirical mathematical model was developed to predict cutting force and surface roughness with good accuracy. The study suggests that higher cutting speed with a small cutting depth is ideal for ensuring the cutting performance and machining quality of PTFE.

JOURNAL OF MANUFACTURING PROCESSES (2022)

Add to Collection

Article Engineering, Mechanical

Materials removal mechanism and multi modes feature for silicon carbide during scratching

Yuhua Huang et al.

Summary: This study focused on the multi modes features during the machining of SiC, using scratching experiments and atomistic simulations. The scratching force and acoustic emission signals were analyzed to distinguish different scratching modes. The localized stress distribution and morphology were analyzed using non-destructive birefringence analysis. Four scratching modes were identified and atomistic simulations were conducted to understand the underlying atom-level behaviors. A qualitative multi layers model was proposed to explain different material removal mechanisms.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2022)

Add to Collection

Review Engineering, Manufacturing

Advances in micro milling: From tool fabrication to process outcomes

Ni Chen et al.

Summary: This article provides a comprehensive overview of micro milling cutters, covering their uniqueness, material removal mechanisms, materials, structures, designs, fabrication techniques, and machining performances. It also outlines several possible future research directions to offer potential insights for the micro milling community and future researchers.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2021)

Add to Collection

Article Engineering, Mechanical

Effects of cutting edge radius in vibration assisted micro machining

Shamsul Arefin et al.

Summary: This study emphasizes the importance of considering the cutting edge radius in microscale machining for understanding tool-workpiece contact relationships and cutting mechanisms. Experimental and finite element simulation results show that variations in the cutting edge radius affect chip thickness, cutting forces, and surface quality in both 1D and 2D VAM processes.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanism of chip formation and surface-defects in orthogonal cutting of soft-brittle potassium dihydrogen phosphate crystals

Qi Liu et al.

Summary: This paper investigates the evolution of different cutting mechanisms with the change of uncut chip thickness (UCT) in KDP orthogonal cutting processes, and proposes a novel theoretical model to explain the cutting phenomena, which is well validated by the analysis of cutting forces and machined surface quality. However, three kinds of surface defects were observed, including micro pits, micro craters, and edge chipping.

MATERIALS & DESIGN (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Laser textured dimple-patterns to govern the surface wettability of superhydrophobic aluminum plates

Wei Tong et al.

Summary: The laser texturing technique can create a regular dimple-pattern array on bare aluminum alloy surface, resulting in superhydrophobic properties which can be adjusted by controlling the dimple-pattern dimensions. The use of fluorescence method reveals the air trapping ability of the superhydrophobic surface, leading to strong mechanical stability of the samples.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

Add to Collection

Article Automation & Control Systems

An experimental investigation on tool wear behaviour of uncoated and coated micro-tools in micro-milling of graphene-reinforced polymer nanocomposites

Niusha Shakoori et al.

Summary: The study investigated the machinability of polymer nanocomposites in micro-scale, with DLC-coated tool showing the best performance in terms of tool wear, surface quality, and cutting forces during micro-milling.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)

Add to Collection

Article Optics

Facile fabrication of microlens array on encapsulation layer for enhancing angular color uniformity of color-mixed light-emitting diodes

Luyao Mei et al.

Summary: This study proposed using a concave microlens array on an encapsulation layer to enhance the angular color uniformity of color-mixed LEDs. By controlling cooling temperatures and introducing a multi-step cooling method, the sag height-to-diameter ratios of the microlens arrays were successfully reduced, leading to improved luminous efficacy of the LEDs.

OPTICS AND LASER TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Indentation size effect, geometrically necessary dislocations and pile-up effects in hardness testing of irradiated nickel

M. A. Mattucci et al.

Summary: The study compared the response of Ni irradiated with protons to the non-irradiated material, based on dislocation density, through TEM analysis and nano/micro-scale indentation tests. The results showed a bi-linear trend in the Nix-Gao model for both irradiated and non-irradiated material, indicating a transition in deformation mechanisms at the nano-scale. It was suggested that the increase in hardness observed in the irradiated material during nanoindentation could be attributed to a higher density of geometrically necessary dislocations.

ACTA MATERIALIA (2021)

Add to Collection

Article Engineering, Manufacturing

Micro-end-milling of carbon nanotube reinforced epoxy nanocomposites manufactured using three roll mill technique

Bao Le et al.

Summary: This study investigates the feasibility of micromachining on nanocomposites and analyzes the effects of factors like filler loading, cutting speed, and feed per tooth. The research reveals that adding multi-walled carbon nanotubes can significantly enhance the machinability of materials, reducing cutting force and improving surface quality.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Materials Science, Ceramics

On the improvement of the ductile removal ability of brittle KDP crystal via temperature effect

Qi Liu et al.

Summary: This study investigates the specific impact of temperature on the deformation behaviors of brittle KDP crystal through nano indentation/scratch methods. The results show that increasing the temperature significantly decreases the hardness and Elastic modulus of KDP crystal, while greatly increasing the fracture toughness, indicating a higher ability of ductile deformation at elevated temperature. Additionally, the scratch length in ductile removal process is extended more than 4 times by increasing temperature, and the quantity and size of brittle features show a reducing trend with temperature increase.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Physics, Multidisciplinary

Fabrication of solid CH-CD multilayer microspheres for inertial confinement fusion

Meifang Liu et al.

Summary: Deuterated polymer microspheres can be efficiently used as a neutron source in fusion experiments, and a new solid deuterated polymer microsphere with a CH-CD multilayer structure has been designed for this purpose. By controlling droplet size and deposition parameters, solid CH-CD microspheres with specified sizes can be successfully prepared. It was found that solid PAMS beads are more suitable as a mandrel for fabricating these microspheres, meeting the physical design requirements for inertial confinement fusion.

MATTER AND RADIATION AT EXTREMES (2021)

Add to Collection

Article Automation & Control Systems

Determination of minimum uncut chip thickness and size effects in micro-milling of P-20 die steel using surface quality and process signal parameters

Priyabrata Sahoo et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Surface morphologies and corresponding hardness evolution during nanoscratching

Shuohua Zhang et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Engineering, Biomedical

Mechanism of material removal in orthogonal cutting of cortical bone

Wei Bai et al.

JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2020)

Add to Collection

Article Automation & Control Systems

An experimental study on fabricating microstructured surface by using LS-WEDM-prepared ball micro end mills

Z. P. Su et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Article Engineering, Manufacturing

Temperature effect on the material removal mechanism of soft-brittle crystals at nano/micron scale

Qi Liu et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2020)

Add to Collection

Article Engineering, Mechanical

Tribological performances of symmetrically micro-textured Ti-6Al-4V alloy for hip joint

Tej Pratap et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2020)

Add to Collection

Article Materials Science, Coatings & Films

Through-mask electrochemical micromachining of micro pillar arrays on aluminum

Yankui Sun et al.

SURFACE & COATINGS TECHNOLOGY (2020)

Add to Collection

Article Engineering, Mechanical

Investigations on burr formation mechanisms in micro milling of high-aspect-ratio titanium alloy ti-6al-4 v structures

Yang Wu et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2020)

Add to Collection

Article Automation & Control Systems

Orthogonal cutting mechanisms of CFRP/Ti6Al4V stacks

Jinyang Xu et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

Add to Collection

Review Engineering, Manufacturing

Advances in ultra-precision machining of micro-structured functional surfaces and their typical applications

Shaojian Zhang et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2019)

Add to Collection

Article Optics

Incident laser modulation by tool marks on micro-milled KDP crystal surface: Numerical simulation and experimental verification

Qi Liu et al.

OPTICS AND LASER TECHNOLOGY (2019)

Add to Collection

Article Materials Science, Coatings & Films

Microstructural investigation of porous titanium coatings, produced by thermal spraying techniques, using plasma atomization and hydride-dehydride powders, for orthopedic implants

P. Gkomoza et al.

SURFACE & COATINGS TECHNOLOGY (2019)

Add to Collection

Article Optics

Investigation on surface/subsurface deformation mechanism and mechanical properties of GGG single crystal induced by nanoindentation

Chen Li et al.

APPLIED OPTICS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

An efficient titanium-containing corundum wheel for grinding CVD diamond films

Hanqing Xu et al.

DIAMOND AND RELATED MATERIALS (2018)

Add to Collection

Article Automation & Control Systems

Micromachining of PMMA-manufacturing of burr-free structures with single-edge ultra-small micro end mills

Ingo G. Reichenbach et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Automation & Control Systems

Fabrication and milling performance of micro ball-end mills with different relief angles

Zhiqiang Liang et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Engineering, Multidisciplinary

Minimum chip thickness determination by means of cutting force signal in micro endmilling

M. H. M. Dib et al.

PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2018)

Add to Collection

Article Materials Science, Coatings & Films

Mechanical micro-texturing of Ti-6Al-4V surfaces for improved wettability and bio-tribological performances

T. Pratap et al.

SURFACE & COATINGS TECHNOLOGY (2018)

Add to Collection

Article Engineering, Manufacturing

An innovative investigation on chip formation mechanisms in micro-milling using natural diamond and tungsten carbide tools

Zhichao Niu et al.

JOURNAL OF MANUFACTURING PROCESSES (2018)

Add to Collection

Article Physics, Applied

Prediction of micro indention depth of TC4 titanium alloy during laser shock processing

Boyong Su et al.

JAPANESE JOURNAL OF APPLIED PHYSICS (2018)

Add to Collection

Article Engineering, Mechanical

Research in minimum undeformed chip thickness and size effect in micro end-milling of potassium dihydrogen phosphate crystal

Ni Chen et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2017)

Add to Collection

Article Engineering, Mechanical

Mechanical and technological aspects of micro ball end milling with various tool inclinations

Szymon Wojciechowski et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2017)

Add to Collection

Article Physics, Fluids & Plasmas

Investigation of working pressure on the surface roughness controlling technology of glow discharge polymer films based on the diagnosed plasma

Ling Zhang et al.

PLASMA SCIENCE & TECHNOLOGY (2017)

Add to Collection

Article Chemistry, Physical

Effects of rf power on chemical composition and surface roughness of glow discharge polymer films

Ling Zhang et al.

APPLIED SURFACE SCIENCE (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Nanoimprint of a 3D structure on an optical fiber for light wavefront manipulation

Giuseppe Calafiore et al.

NANOTECHNOLOGY (2016)

Add to Collection

Article Mechanics

On the toughness measurement for ductile polymers by orthogonal cutting

H. Wang et al.

ENGINEERING FRACTURE MECHANICS (2015)

Add to Collection

Article Engineering, Manufacturing

Size effect and minimum chip thickness in micromilling

Fernando Brandao de Oliveira et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2015)

Add to Collection

Article Engineering, Manufacturing

On the mechanics and material removal mechanisms of vibration-assisted cutting of unidirectional fibre-reinforced polymer composites

Weixing Xu et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2014)

Add to Collection

Article Mechanics

Tool sharpness as a factor in machining tests to determine toughness

B. R. K. Blackman et al.

ENGINEERING FRACTURE MECHANICS (2013)

Add to Collection

Article Engineering, Manufacturing

Prediction of cutting forces in three and five-axis ball-end milling with tool indentation effect

Oguzhan Tuysuz et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2013)

Add to Collection

Article Engineering, Manufacturing

Characterization and Micromilling of Flow Induced Aligned Carbon Nanotube Nanocomposites

Mehdi Mahmoodi et al.

JOURNAL OF MICRO AND NANO-MANUFACTURING (2013)

Add to Collection

Article Engineering, Industrial

Ultra-precision cryogenic machining of viscoelastic polymers

Yasuhiro Kakinuma et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2012)

Add to Collection

Article Engineering, Multidisciplinary

Study of cutting force and surface roughness in the turning of polytetrafluoroethylene composites with a polycrystalline diamond tool

Catalin Fetecau et al.

MEASUREMENT (2012)

Add to Collection

Article Engineering, Multidisciplinary

Force coefficients identification considering inclination angle for ball-end finish milling

Qingyuan Cao et al.

PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2012)

Add to Collection

Review Engineering, Manufacturing

Review on diamond-machining processes for the generation of functional surface structures

Ekkard Brinksmeier et al.

CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2012)

Add to Collection

Article Engineering, Manufacturing

Investigation of cutting force behaviour considering the effect of cutting edge radius in the micro-scale milling of AISI 1045 steel

I-S Kang et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2011)

Add to Collection

Article Mechanics

Determining fracture toughness from cutting tests on polymers

Y. Patel et al.

ENGINEERING FRACTURE MECHANICS (2009)

Add to Collection

Article Engineering, Manufacturing

Effect of Carbon Nanotube (CNT) Loading on the Thermomechanical Properties and the Machinability of CNT-Reinforced Polymer Composites

J. Samuel et al.

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2009)

Add to Collection

Article Engineering, Manufacturing

An investigation into the mechanics of cutting using data from orthogonally cutting Nylon 66

D. J. Wyeth

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)

Add to Collection

Article Engineering, Manufacturing

Modelling and analysis of micro scale milling considering size effect, micro cutter edge radius and minimum chip thickness

Xinmin Lai et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)

Add to Collection

Article Materials Science, Multidisciplinary

Statistical study of surface roughness in turning of peek composites

G. Petropoulos et al.

MATERIALS & DESIGN (2008)

Add to Collection

Article Engineering, Electrical & Electronic

Modeling of three-dimensional cutting forces in micro-end-milling

Chengfeng Li et al.

JOURNAL OF MICROMECHANICS AND MICROENGINEERING (2007)

Add to Collection

Article Nuclear Science & Technology

Gas etching to obtain germanium doped chx microshells compatible with the laser megajoule target specifications

M Theobald et al.

FUSION SCIENCE AND TECHNOLOGY (2006)

Add to Collection

Review Materials Science, Multidisciplinary

Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology

WC Oliver et al.

JOURNAL OF MATERIALS RESEARCH (2004)

Add to Collection

Article Engineering, Mechanical

The role of viscous deformation in the machining of polymers

KQ Xiao et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2002)

Add to Collection

Article Nuclear Science & Technology

Coating and mandrel effects on fabrication of glow discharge polymer NIF scale indirect drive capsules

A Nikroo et al.

FUSION SCIENCE AND TECHNOLOGY (2002)

Add to Collection

Article Engineering, Manufacturing

A new model and analysis of orthogonal machining with an edge-radiused tool

J Manjunathaiah et al.

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2000)

Add to Collection

Material removal mechanism and microstructure fabrication of GDP during micro-milling

Related references

Export Citation

Share Paper