☆ 4.6 Article

Analytical modeling of effective depth of cut for ductile materials via abrasive waterjet machining

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2023)

Related references

Note: Only part of the references are listed.

Article Engineering, Multidisciplinary

Influence of Selected Diagnostic Parameters on the Quality of AWJ Cutting Surface

Tomasz Wala et al.

Summary: This article reviews research methods for the cutting process using abrasive waterjet machining, with a focus on assessing the possibility of monitoring the process. It evaluates the influence of various parameters on the machined surface and proposes a methodology for on-line process monitoring and supervision.

ADVANCES IN SCIENCE AND TECHNOLOGY-RESEARCH JOURNAL (2022)

Add to Collection

Article Automation & Control Systems

Erosion field characteristics of depth-control micro-hole profiles machined by abrasive waterjet based on FSI coupling

Yemin Yuan et al.

Summary: This article presents a new model to simulate the erosion footprint profiles of abrasive waterjet (AWJ) processing, investigating the impact of jet-plume capabilities and workpiece physical properties. The study shows that the simulated footprints profiles are in good agreement with experimental data, demonstrating high accuracy and reliability.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Investigating the effects of abrasive water jet machining parameters on surface integrity, chemical state in machining of Ti-6Al-4V

S. Ramakrishnan

Summary: This study investigates the effects of abrasive waterjet milling (AWJM) on the surface roughness and microhardness of titanium alloy. The results show that waterjet pressure is a crucial factor in reducing surface roughness, increasing striations, and decreasing waviness. Furthermore, the AWJM process leads to a higher microhardness due to the material's permanent plastic deformation. X-Ray Diffraction analysis also reveals a reduction in lattice strain and an increase in crystallite size during the AWJM process, attributed to the presence of TiOxCx.

MATERIALS TODAY COMMUNICATIONS (2022)

Add to Collection

Article Mechanics

Mechanisms of pop-up delamination in laminated composites pierced by the initial pure waterjet in abrasive waterjet machining

Yiwen Gu et al.

Summary: This paper investigates the formation mechanism of delamination in entrainment abrasive waterjet machines and finds that the delamination phenomenon is mainly caused by the material's response to shock pressure and shear stress. Furthermore, the study also reveals that the delamination is influenced by water pressure and the delamination area varies among different composite materials.

COMPOSITE STRUCTURES (2022)

Add to Collection

Article Engineering, Mechanical

Influence of submerged micro-abrasive waterjet peening on surface integrity and fatigue performance of TA19 titanium alloy

Shu-Lei Yao et al.

Summary: This study investigates the influence of submerged micro-abrasive waterjet peening (SMA-WJP) on the surface integrity and fatigue properties of TA19 titanium alloy. The results show that SMA-WJP treatment forms a plastic deformation layer and compressive residual stress layer, improving the surface integrity and fatigue life. Additionally, nanocrystals and high density of dislocations are formed on the surface of the SMA-WJP treated specimen.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

Add to Collection

Article Engineering, Manufacturing

Predictive modeling approach for the jet lag in multi-pass cutting of thick materials using abrasive waterjet

Jianfeng Chen et al.

Summary: In this study, a multi-pass cutting strategy is proposed to reduce jet lag and improve surface quality by fixing the starting position and cutting parameters. A predictive model of jet lag is developed using particle erosion theories and a dimensionless analysis method, which enables the prediction of jet lag for different cutting depths and parameters.

JOURNAL OF MANUFACTURING PROCESSES (2022)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Experimental investigation and striation study of Inconel 718 by using abrasive water jet drilling

M. Rajesh et al.

Summary: Abrasive waterjet (AWJ) technology is a viable production method for machining metal matrices with superior physical and mechanical characteristics. This study investigates the quality of striation angle and surface morphology/integrity in the AWJ drilling of Inconel 718 material, exploring the impact of various operating variables.

MATERIALS TODAY-PROCEEDINGS (2022)

Add to Collection

Article Engineering, Manufacturing

Abrasive water jet machining on Ti metal-interleaved basalt-flax fiber laminate

M. Rajesh et al.

Summary: The study focuses on the machining of high strength and shock-absorbent Metal Fiber Laminate (MFL) using an abrasive water jet method. Results show that significant reduction in surface roughness and kerf ratio can be achieved by adjusting water jet pressure and abrasive mass flow rate.

MATERIALS AND MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Manufacturing

Experimental investigation and optimization of abrasive waterjet machining parameters for GFRP composites using metaphor-less algorithms

Dharmagna R. Tripathi et al.

Summary: The study explores the influence of cutting speed and abrasive flow rate on GFRP composites. The use of Rao 1, Rao 2, and Rao 3 algorithms helped determine the ideal machining conditions, showing more effectiveness in terms of computational time and effort. Mathematical models were established using nonlinear regression statistics to correlate variables and output attributes.

MATERIALS AND MANUFACTURING PROCESSES (2021)

Add to Collection

Review Engineering, Mechanical

Abrasive water jet machining techniques and parameters: a state of the art, open issue challenges and research directions

A. Anu Kuttan et al.

Summary: Various issues in manufacturing operations have been solved by superior machining methods recently. The abrasive water jet machining (AWJM) process has been established based on advanced machining techniques and is widely used in manufacturing industries. Different types of AWJM processes, factors influencing parameters, work materials, and modeling process have been categorized for research.

JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2021)

Add to Collection

Article Engineering, Manufacturing

Cutting of St37 steel plates in stacked form with abrasive water jet

Mustafa Armagan

Summary: This study investigated the cutting of stacked St37 steel plates with abrasive water jet (AWJ) and found that the most effective parameters for cutting performance were abrasive mass flow rate and inter-stack distance. A concept for multi-simultaneous cutting was developed based on mathematical differences of surface roughness and kerf taper angle, leading to the determination of optimum levels of experimental parameters for minimum mathematical differences.

MATERIALS AND MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Aerospace

Investigation of effect of abrasive water jet (AWJ) machining parameters on aramid fiber-reinforced polymer (AFRP) composite materials

Sitki Akincioglu

Summary: Reliable results were obtained using Taguchi-based GRA in drilling AFRP composite material with AWJ, leading to improved hole quality and cost savings. The new approach of detailed analysis using Taguchi method and multi-decision Taguchi-based gray relation analysis in AFRP composite material drilling using AWJ has proven to be effective.

AIRCRAFT ENGINEERING AND AEROSPACE TECHNOLOGY (2021)

Add to Collection

Review Engineering, Manufacturing

Abrasive Water Jet Machining process: A state of art of review

Yuvaraj Natarajan et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection

Article Engineering, Industrial

Dual-processing by abrasive waterjet machining-A method for machining and surface modification of nickel-based superalloy

Zhirong Liao et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)

Add to Collection

Article Automation & Control Systems

Numerical research on kerf characteristics of abrasive waterjet machining based on the SPH-DEM-FEM approach

Mingming Du et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Article Engineering, Manufacturing

Boundary condition for deformation wear mode material removal in abrasive waterjet milling: Theoretical and experimental analyses

R. Srikanth et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2019)

Add to Collection

Article Green & Sustainable Science & Technology

Experimental Investigation on Cryogenic Assisted Abrasive Water Jet Machining of Aluminium Alloy

Yuvaraj Natarajan et al.

INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING-GREEN TECHNOLOGY (2019)

Add to Collection

Article Chemistry, Physical

Defect Analysis and Detection of Cutting Regions in CFRP Machining Using AWJM

Pedro F. Mayuet Ares et al.

MATERIALS (2019)

Add to Collection

Review Engineering, Manufacturing

A review on the erosion mechanisms in abrasive waterjet micromachining of brittle materials

T. Nguyen et al.

INTERNATIONAL JOURNAL OF EXTREME MANUFACTURING (2019)

Add to Collection

Article Engineering, Mechanical

Semi-empirical model on MRR and overcut in WEDM process of pure titanium using multi-objective desirability approach

Anish Kumar et al.

JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2015)

Add to Collection

Article Engineering, Mechanical

On ultrahigh velocity micro-particle impact on steels-A single impact study

Wei Yi Li et al.

WEAR (2013)

Add to Collection

Article Automation & Control Systems

Application of Taguchi design for quality characterization of abrasive water jet machining of TRIP sheet steels

John Kechagias et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2012)

Add to Collection

Article Engineering, Manufacturing

An Experimental Study on the Depth of Cut of Granite in Abrasive Waterjet Cutting

Izzet Karakurt et al.

MATERIALS AND MANUFACTURING PROCESSES (2012)

Add to Collection

Article Engineering, Mechanical

Depth of cut models for multipass abrasive waterjet cutting of alumina ceramics with nozzle oscillation

Jun Wang

FRONTIERS OF MECHANICAL ENGINEERING (2010)

Add to Collection

Article Engineering, Manufacturing

A study of delamination on graphite/epoxy composites in abrasive waterjet machining

D. K. Shanmugam et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2008)

Add to Collection

Article Engineering, Manufacturing

Effect of liquid properties on the stability of an abrasive waterjet

T. Nguyen et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)

Add to Collection

Article Engineering, Mechanical

Modelling of the abrasive water jet cutting process

RT Deam et al.

WEAR (2004)

Add to Collection

Article Engineering, Industrial

The cutting performance in multipass abrasive waterjet machining of industrial ceramics

J Wang et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)

Add to Collection

Article Materials Science, Ceramics

The effect of the jet impact angle on the cutting performance in AWJ machining of alumina ceramics

J Wang

ADVANCES IN ABRASIVE TECHNOLOGY V (2003)

Add to Collection

© Peeref 2019-2024. All rights reserved.