Related references
Note: Only part of the references are listed.Lucas-Washburn Equation-Based Modeling of Capillary-Driven Flow in Porous Systems
Jianchao Cai et al.
LANGMUIR (2021)
Probing Ink-Powder Interactions during 3D Binder Jet Printing Using Time-Resolved X-ray Imaging
Srimanta Barui et al.
ACS APPLIED MATERIALS & INTERFACES (2020)
Infiltration of impacting droplets into porous substrates
D. J. Bouchard et al.
EXPERIMENTS IN FLUIDS (2020)
Understanding pore formation and the effect on mechanical properties of High Speed Sintered polyamide-12 parts: A focus on energy input
Zicheng Zhu et al.
MATERIALS & DESIGN (2020)
Binder jetting: A review of process, materials, and methods
Mohsen Ziaee et al.
ADDITIVE MANUFACTURING (2019)
Characterizing Binder-Powder Interaction in Binder Jetting Additive Manufacturing Via Sessile Drop Goniometry
Yun Bai et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2019)
Real time observation of binder jetting printing process using high-speed X-ray imaging
Niranjan D. Parab et al.
SCIENTIFIC REPORTS (2019)
Mathematical modelling of water absorption and evaporation in a pharmaceutical tablet during film coating
Charalampos Christodoulou et al.
CHEMICAL ENGINEERING SCIENCE (2018)
Hydrophobic/hydrophilic static powder beds: Competing horizontal spreading and vertical imbibition mechanisms of a single droplet
Aquino L. Mundozah et al.
POWDER TECHNOLOGY (2018)
Droplet Imbibition into Paper Coating Layer: Pore-Network Modeling Simulation
X. Yin et al.
TRANSPORT IN POROUS MEDIA (2018)
A Low-Cost Flash Photographic System for Visualization of Droplets in Drop-on-Demand Inkjet
Huicong Jiang et al.
JOURNAL OF IMAGING SCIENCE AND TECHNOLOGY (2018)
Evaluation of the mechanical performance of polymer parts fabricated using a production scale multi jet fusion printing process
Heather J. O'Connor et al.
ADDITIVE MANUFACTURING (2018)
O Mechanical characterization of 3D-printed polymers
John Ryan C. Dizon et al.
ADDITIVE MANUFACTURING (2018)
Droplet impact on heated powder bed
Dongdong Liu et al.
SOFT MATTER (2018)
Impact of extended sintering times on mechanical properties in PA-12 parts produced by powderbed fusion processes
Garrett Craft et al.
ADDITIVE MANUFACTURING (2018)
Capillary Drop Penetration Method to Characterize the Liquid Wetting of Powders
Zhanjie Liu et al.
LANGMUIR (2017)
Wetting and Coalescence of Drops of Self-Healing Agents on Electrospun Nanofiber Mats
Seongpil An et al.
LANGMUIR (2017)
Wetting of inclined nano-textured surfaces by self-healing agents
Seongpil An et al.
APPLIED PHYSICS LETTERS (2017)
Three-dimensional simulation of micrometer-sized droplet impact and penetration into the powder bed
Hua Tan
CHEMICAL ENGINEERING SCIENCE (2016)
Impact of aqueous suspension drops onto non-wettable porous membranes: Hydrodynamic focusing and penetration of nanoparticles
R. P. Sahu et al.
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2015)
Quantification of powder wetting by drop penetration time
Merel L. M. Oostveen et al.
POWDER TECHNOLOGY (2015)
Raindrop impact on sand: a dynamic explanation of crater morphologies
Song-Chuan Zhao et al.
SOFT MATTER (2015)
Infiltration and dimensional scaling of inkjet droplets on thick isotropic porous materials
Asaf Oko et al.
MICROFLUIDICS AND NANOFLUIDICS (2014)
Fog-water collection for community use
Mussie Fessehaye et al.
RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2014)
A Regime Map for Granule Formation by Drop Impact on Powder Beds
Heather N. Emady et al.
AICHE JOURNAL (2013)
High-speed imaging in fluids
Michel Versluis
EXPERIMENTS IN FLUIDS (2013)
Modeling the granule formation mechanism from single drop impact on a powder bed
Heather N. Emady et al.
JOURNAL OF COLLOID AND INTERFACE SCIENCE (2013)
Drop spreading and penetration into pre-wetted powders
J. O. Marston et al.
POWDER TECHNOLOGY (2013)
The influence of powder properties on the imbibation rate
D. Hellborg et al.
COLLOIDS AND SURFACES B-BIOINTERFACES (2012)
Impact of a liquid drop on a granular medium: Inertia, viscosity and surface tension effects on the drop deformation
E. Nefzaoui et al.
EXPERIMENTAL THERMAL AND FLUID SCIENCE (2012)
Investigation of water seepage through porous media using X-ray imaging technique
Sung Yong Jung et al.
JOURNAL OF HYDROLOGY (2012)
A GENERAL FORMULA FOR CAPILLARY SUCTION-PRESSURE IN POROUS MEDIA
Reza Masoodi et al.
JOURNAL OF POROUS MEDIA (2012)
Source-like Solution for Radial Imbibition into a Homogeneous Semi-infinite Porous Medium
Junfeng Xiao et al.
LANGMUIR (2012)
Early regimes of capillary filling
Siddhartha Das et al.
PHYSICAL REVIEW E (2012)
Wettability of mineral and metallic powders: Applicability and limitations of sessile drop method and Washburn's technique
Laura Susana et al.
POWDER TECHNOLOGY (2012)
Length and time scales of a liquid drop impact and penetration into a granular layer
Hiroaki Katsuragi
JOURNAL OF FLUID MECHANICS (2011)
Granule formation mechanisms and morphology from single drop impact on powder beds
Heather N. Emady et al.
POWDER TECHNOLOGY (2011)
Drop Impact, Spreading, Splashing, and Penetration into Electrospun Nanofiber Mats
Andreas N. Lembach et al.
LANGMUIR (2010)
Infiltration of liquid droplets into porous media: Effects of dynamic contact angle and contact angle hysteresis
Markus Hilpert et al.
INTERNATIONAL JOURNAL OF MULTIPHASE FLOW (2009)
High-Speed Imaging of Drops and Bubbles
S.T. Thoroddsen et al.
Annual Review of Fluid Mechanics (2008)
Spreading of liquid droplets on proton exchange membrane of a direct alcohol fuel cell
Tirupati R. Keshav et al.
CHEMICAL ENGINEERING SCIENCE (2007)
Mercury porosimetry: A general (practical) overview
H Giesche
PARTICLE & PARTICLE SYSTEMS CHARACTERIZATION (2006)
Drop penetration into porous powder beds
KP Hapgood et al.
JOURNAL OF COLLOID AND INTERFACE SCIENCE (2002)
Spreading and infiltration of inkjet-printed polymer solution droplets on a porous substrate
RK Holman et al.
JOURNAL OF COLLOID AND INTERFACE SCIENCE (2002)