☆ 4.7 Article

Turbine nozzle endwall aero-thermal characteristics under combustor louver coolant with interface cavity

APPLIED THERMAL ENGINEERING (2023)

Related references

Note: Only part of the references are listed.

Article Thermodynamics

Comparisons of blade tip phantom cooling effectiveness for two tip structures with three tip clearances

Feng Li et al.

Summary: This study investigates the phantom cooling effects on the blade tip region of a gas turbine, showing that the flat tip performs better in phantom cooling compared to the squealer tip. Increasing the tip clearance weakens phantom cooling effectiveness on the flat tip forepart but enhances it on the rear part. Conversely, the phantom cooling effectiveness values decrease as the tip clearance increases for the squealer tip.

APPLIED THERMAL ENGINEERING (2022)

Add to Collection

Article Thermodynamics

Non-axisymmetric endwall contour optimization and performance assessment as affected by simulated swirl purge flow and backward hole injection

Kaiyuan Zhang et al.

Summary: A shape optimization system using the kriging model, NSGA-II algorithm, and CFD simulation was constructed to balance endwall cooling and blade phantom cooling performances. Two optimal contours were found to significantly increase endwall adiabatic effectiveness, but the flat endwall achieved the best phantom cooling performance. Both design and off-design conditions showed that the contours increased slot coolant coverage on the pressure side endwall and weakened the tendency for hole coolant to cover the suction side hot ring.

INTERNATIONAL JOURNAL OF THERMAL SCIENCES (2022)

Add to Collection

Article Thermodynamics

Thermal-hydraulic performance of additively manufactured lattices for gas turbine blade trailing edge cooling

Inderjot Kaur et al.

Summary: Gas turbine blade trailing edge cooling is a challenging task due to strict geometrical constraints and thermal stresses. Traditional pin-fin structures are commonly used for internal cooling, but lattice structures have shown better heat transfer performance. In this study, four different lattice unit cell topologies were additively manufactured in 420 Stainless Steel using Binder Jetting technology, and their heat transfer capabilities were evaluated.

APPLIED THERMAL ENGINEERING (2022)

Add to Collection

Article Thermodynamics

Experimental investigation of effusion and transpiration air cooling for single turbine blade

Mingeon Kim et al.

Summary: This study investigated the effectiveness of effusion and transpiration cooling for turbine blades, with experiments conducted in a high-temperature wind tunnel. The research found that transpiration cooling achieved 34% and 25% higher cooling effectiveness compared to effusion and internal cooling respectively.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Energy & Fuels

Numerical study of effusion cooling of a gas turbine combustor liner

Jin Wang et al.

Summary: Effusion cooling is an effective method for cooling high-temperature components in gas turbines, with the inclination angle of cooling holes impacting cooling effectiveness. Numerical simulations showed that a 30° inclination angle provided the best cooling effect, reducing maximum temperature by 31.7%. Uniform outlet temperature distribution is crucial for turbine blade protection, with a 30% inclination angle resulting in the most uniform temperature distribution.

FUEL (2021)

Add to Collection

Article Engineering, Mechanical

Transonic Turbine Vane Endwall Film Cooling Using the Pressure-Sensitive Paint Measurement Technique

Chao-Cheng Shiau et al.

JOURNAL OF TURBOMACHINERY-TRANSACTIONS OF THE ASME (2020)

Add to Collection

Article Thermodynamics

Turbine vane endwall film cooling with barchan-dune shaped ramp in a single-passage transonic wind tunnel

Wenwu Zhou et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2020)

Add to Collection

Article Thermodynamics

Effects of simulated swirl purge flow and mid-passage gap leakage on turbine blade platform cooling and suction surface phantom cooling performance

Kaiyuan Zhang et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2019)

Add to Collection

Article Thermodynamics

Turbine vane endwall film cooling from mid-chord or downstream rows and upstream coolant injection

Nian Wang et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2019)

Add to Collection

Article Thermodynamics

Turbine Vane Endwall Film Cooling Comparison From Five Film-Hole Design Patterns and Three Upstream Injection Angles

Chao-Cheng Shiau et al.

JOURNAL OF THERMAL SCIENCE AND ENGINEERING APPLICATIONS (2019)

Add to Collection

Article Engineering, Aerospace

Influence of fillet shapes on secondary flow field in a transonic axial flow turbine stage

K. Ananthakrishnan et al.

AEROSPACE SCIENCE AND TECHNOLOGY (2018)

Add to Collection

Article Engineering, Mechanical

Experimental and Computational Study of the Effect of Momentum-Flux Ratio on High-Pressure Nozzle Guide Vane Endwall Cooling Systems

Francesco Ornano et al.

JOURNAL OF TURBOMACHINERY-TRANSACTIONS OF THE ASME (2017)

Add to Collection

Article Thermodynamics

Heat transfer measurement near endwall region of first stage gas turbine nozzle having platform misalignment at combustor-turbine interface

Heeyoon Chung et al.

INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER (2016)

Add to Collection

Article Thermodynamics

Effect of discrete-hole arrangement on film-cooling effectiveness for the endwall of a turbine blade cascade

Francesca Satta et al.

APPLIED THERMAL ENGINEERING (2015)

Add to Collection

Article Engineering, Mechanical

The Effects of Vane Showerhead Injection Angle and Film Compound Angle on Nozzle Endwall Cooling (Phantom Cooling)

Luzeng Zhang et al.

JOURNAL OF TURBOMACHINERY-TRANSACTIONS OF THE ASME (2015)

Add to Collection

Article Engineering, Mechanical

Impact of Swirl Flow on the Cooling Performance of an Effusion Cooled Combustor Liner

B. Wurm et al.

JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME (2012)

Add to Collection

Article Engineering, Mechanical

Adiabatic and Overall Effectiveness Measurements of an Effusion Cooling Array for Turbine Endwall Application

Bruno Facchini et al.

JOURNAL OF TURBOMACHINERY-TRANSACTIONS OF THE ASME (2010)

Add to Collection

Article Engineering, Mechanical

Investigation of velocity profiles for effusion cooling of a combustor liner

J. J. Scrittore et al.

JOURNAL OF TURBOMACHINERY-TRANSACTIONS OF THE ASME (2007)

Add to Collection

Article Engineering, Aerospace

Gas turbine film cooling

DG Bogard et al.

JOURNAL OF PROPULSION AND POWER (2006)

Add to Collection

Article Engineering, Mechanical

Combustor turbine interface studies - Part 1: Endwall effectiveness measurements

WF Colban et al.

JOURNAL OF TURBOMACHINERY-TRANSACTIONS OF THE ASME (2003)

Add to Collection

Article Engineering, Mechanical

Combustor turbine interface studies - Part 2: Flow and thermal field measurements

WF Colban et al.

JOURNAL OF TURBOMACHINERY-TRANSACTIONS OF THE ASME (2003)

Add to Collection

© Peeref 2019-2024. All rights reserved.