☆ 4.6 Article

Effect of Sintering Temperature on Mechanical Behaviors of an Oxide Fiber-Reinforced Oxide Matrix Composite

ADVANCED ENGINEERING MATERIALS (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Evolution of Damage in All-Oxide Ceramic Matrix Composite After Cyclic Loading

Andreas Kupsch et al.

Summary: The study investigates the stiffness evolution of a sandwich-like laminate of Al2O3-15%vol. ZrO2 matrix reinforced with Nextel 610 fibers under tension as a function of cycles. The stiffness of the composite degrades with increasing cycles due to microcracking. A modeling strategy is developed to calculate the equivalent stiffness and estimate microcrack density and increase, providing insights into damage mechanisms.

ADVANCED ENGINEERING MATERIALS (2022)

Add to Collection

Article Mechanics

Study on the macro- and micro-mechanical properties of quartz fiber reinforced polyimide resin matrix composite after thermal aging

Xiaofei Chen et al.

Summary: In this study, a high glass transition temperature polyimide resin was used as a matrix to prepare a quartz fiber reinforced polyimide resin composite. The effects of thermal aging on the mechanical properties and interface evolution of the composite were investigated. The results showed that the mechanical properties of the composite were significantly affected by high temperature aging, with a decrease in interfacial shear strength and a subsequent reduction in flexural strength.

COMPOSITE STRUCTURES (2022)

Add to Collection

Article Materials Science, Composites

Effect of Sintering Temperature on the Interfacial and Mechanical Properties of SiC Fiber Reinforced Mullite Matrix Composites

Zhenghao Tian et al.

Summary: SiC fiber reinforced mullite matrix composites were prepared through a sol-gel process, with the sintering temperature significantly affecting the interfacial and mechanical properties. A specific mullite phase could be formed at 1200 degrees C, leading to increased Young's modulus and hardness of the matrix. The interfacial interaction between fiber and matrix was also enhanced with sintering temperature, impacting the macro-mechanical properties of the composites.

APPLIED COMPOSITE MATERIALS (2021)

Add to Collection

Article Materials Science, Ceramics

Effect of C/SiC interphase on interfacial and mechanical properties of SiC fiber reinforced mullite matrix composites

Guihang Deng et al.

Summary: The introduction of C/SiC interphase significantly reduced the interfacial shear strength and greatly enhanced the macro fracture toughness of SiCf/Mu composite, demonstrating the efficiency of using this method.

JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Ceramics

Microstructure and mechanical properties improvement of the NextelTM 610 fiber reinforced alumina composite

Ru Jiang et al.

Summary: In this study, a high solid content alumina slurry was used to prepare NextelTM 610 fiber reinforced alumina composite, and a rapid lamination route was proposed. The composite showed reduced shrinkage cracks in the matrix and maintained a porous structure. The mechanical properties of the N610/alumina composite, with weak matrix and weak interface, were investigated and found to be higher than many oxide/oxide composites.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Ceramics

Effects of sintering temperature on mechanical properties of alumina fiber reinforced alumina matrix composites

Zhu Chengxin et al.

JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Ceramics

A multiscale methodology quantifying the sintering temperature-dependent mechanical properties of oxide matrix composites

Ru Jiang et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2018)

Add to Collection

Review Materials Science, Multidisciplinary

Fibre-reinforced multifunctional SiC matrix composite materials

X. W. Yin et al.

INTERNATIONAL MATERIALS REVIEWS (2017)

Add to Collection

Article Engineering, Mechanical

Development and Test of Oxide/Oxide Ceramic Matrix Composites Combustor Liner Demonstrators for Aero-engines

Thomas Behrendt et al.

JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME (2017)

Add to Collection

Article Materials Science, Ceramics

Microstructure and mechanical behaviour of a Nextel™610/alumina weak matrix composite subjected to tensile and compressive loadings

C. Ben Ramdane et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2017)

Add to Collection

Article Engineering, Multidisciplinary

Processing-temperature dependent micro- and macro-mechanical properties of SiC fiber reinforced SiC matrix composites

L. W. Yang et al.

COMPOSITES PART B-ENGINEERING (2017)

Add to Collection

Article Engineering, Multidisciplinary

Sol-gel temperature dependent ductile-to-brittle transition of aluminosilicate fiber reinforced silica matrix composite

L. W. Yang et al.

COMPOSITES PART B-ENGINEERING (2017)

Add to Collection

Article Chemistry, Physical

Enhancing the fracture resistance of carbon fiber reinforced SiC matrix composites by interface modification through a simple fiber heat-treatment process

H. T. Liu et al.

CARBON (2016)

Add to Collection

Article Materials Science, Ceramics

Microstress in Reaction-Bonded SiC from Crystallization Expansion of Silicon

Bradley L. Wing et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2016)

Add to Collection

Article Chemistry, Physical

Advanced structural ceramics in aerospace propulsion

Nitin P. Padture

NATURE MATERIALS (2016)

Add to Collection

Article Materials Science, Ceramics

Interface controlled micro- and macro- mechanical properties of aluminosilicate fiber reinforced SiC matrix composites

H.T. Liu et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2016)

Add to Collection

Article Engineering, Manufacturing

Assessment of three oxide/oxide ceramic matrix composites: Mechanical performance and effects of heat treatments

E. Volkmann et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2015)

Add to Collection

Article Materials Science, Ceramics

Mechanical characterisation of a fibre reinforced oxide/oxide ceramic matrix composite

D. T. Di Salvo et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2015)

Add to Collection

Article Materials Science, Ceramics

ZrO2 fiber-matrix interfaces in alumina fiber-reinforced model composites

Diego Blaese et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2015)

Add to Collection

Article Materials Science, Ceramics

Effects of sintering temperature on mechanical properties of 3D mullite fiber (ALF FB3) reinforced mullite composites

Yi Wang et al.

CERAMICS INTERNATIONAL (2013)

Add to Collection

Article Materials Science, Composites

A methodology to measure the interface shear strength by means of the fiber push-in test

M. Rodriguez et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2012)

Add to Collection

Article Materials Science, Ceramics

Developments in oxide fiber composites

Frank W. Zok

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2006)

Add to Collection

Article Materials Science, Ceramics

Progress in processing and performance of porous-matrix oxide/oxide composites

RA Simon

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2005)

Add to Collection

Article Materials Science, Composites

Design, preparation and properties of non-oxide CMCs for application in engines and nuclear reactors: an overview

R Naslain

COMPOSITES SCIENCE AND TECHNOLOGY (2004)

Add to Collection

Review Materials Science, Multidisciplinary

Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology

WC Oliver et al.

JOURNAL OF MATERIALS RESEARCH (2004)

Add to Collection

Article Materials Science, Ceramics

Characterization and high-temperature mechanical behavior of an oxide/oxide composite

LP Zawada et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2003)

Add to Collection

Article Engineering, Aerospace

State of the art and perspectives for oxide/oxide composites

M Parlier et al.

AEROSPACE SCIENCE AND TECHNOLOGY (2003)

Add to Collection

Article Materials Science, Ceramics

Effectiveness of monazite coatings in Oxide/Oxide composites after long-term exposure at high temperature

KA Keller et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2003)

Add to Collection

Article Materials Science, Ceramics

Effects of matrix porosity on the mechanical properties of a porous-matrix, all-oxide ceramic composite

MA Mattoni et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2001)

Add to Collection

Article Engineering, Manufacturing

Fabrication of high-temperature resistant oxide ceramic matrix composites

IAH Al-Dawery et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2001)

Add to Collection

Article Engineering, Mechanical

Advances in oxide-oxide CMC

RA Jurf et al.

JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.