☆ 4.5 Review

Friction behaviors in the metal cutting process: state of the art and future perspectives

INTERNATIONAL JOURNAL OF EXTREME MANUFACTURING (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Ceramics

Friction and wear properties of TiAlN coated tools with different levels of surface integrity

Kaishuo Chang et al.

Summary: This study investigates the influence of surface integrity on the high-speed sliding wear and cutting performance of coated tools. The results show that low surface roughness effectively reduces the friction coefficient, while high surface hardness and compressive residual stress minimize fluctuations in the friction coefficient. The cutting performance of coated tools is primarily influenced by surface hardness and residual stress.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Engineering, Manufacturing

Effect of geometrical parameters and tool pattern of multi-tooth sawing on cutting of sheet molding compound composite: FE study

Amira Hassouna et al.

Summary: The article introduces a new tool design with fine-tuned geometric parameters to reduce machining damage and improve the machinability of SMC composite materials. The study shows that the rake angle plays a significant role in cutting and thrust forces, while the inclination angle is not as influential. The complementary side cutting edge angle mainly affects the thrust force.

MACHINING SCIENCE AND TECHNOLOGY (2022)

Add to Collection

Review Engineering, Mechanical

Nano-enhanced biolubricant in sustainable manufacturing: From processability to mechanisms

Yanbin Zhang et al.

Summary: This paper investigates the application of nano-enhanced biolubricant (NEBL) in minimum quantity lubrication (MQL) machining and analyzes its performance and mechanisms in processes such as turning, milling, and grinding. By quantitatively comparing with biolubricant, the advanced lubrication and heat transfer mechanisms of NEBL are revealed. Furthermore, future development directions and improvement methods for NEBL are proposed.

FRICTION (2022)

Add to Collection

Review Engineering, Manufacturing

Fundamentals of atomic and close-to-atomic scale manufacturing: a review

Jian Gao et al.

Summary: This paper discusses the theoretical boundary of ACSM, the physical mechanisms of atomic interactions and energy beams-matter interactions, the dominant mechanisms of ACSM processes, and the current digital research and comparison. Future research directions are proposed to support and accelerate the industrial-scale implementation of ACSM.

INTERNATIONAL JOURNAL OF EXTREME MANUFACTURING (2022)

Add to Collection

Article Engineering, Manufacturing

Tool path generation and optimization for freeform surface diamond turning based on an independently controlled fast tool servo

Yusuke Sato et al.

Summary: This study focused on optimizing tool path generation strategies for independently controlled FTS, using the ring method and the mesh method to generate tool paths, predicting machined surface profiles through simulation, and optimizing control point generation parameters to reduce form errors in the machined surfaces. After tool path optimization, the peak-to-valley form errors were significantly reduced for both a two-dimensional sinewave and a micro-lens array, demonstrating the effectiveness of the proposed strategies.

INTERNATIONAL JOURNAL OF EXTREME MANUFACTURING (2022)

Add to Collection

Review Engineering, Manufacturing

Intermolecular and surface forces in atomic-scale manufacturing

Xin Hou et al.

Summary: Atomic and close-to-atomic scale manufacturing (ACSM) has broad applications in various fields, but faces challenges in manipulating materials at the atomic scale based on classical mechanics theory. Understanding and using intermolecular and surface forces are essential for better designing of ACSM. Existing atomic transformation and self-assembly processes provide important references for regulating intermolecular interactions.

INTERNATIONAL JOURNAL OF EXTREME MANUFACTURING (2022)

Add to Collection

Review Engineering, Manufacturing

Advances in the design and manufacturing of novel freeform optics

Sumit Kumar et al.

Summary: Freeform optics has become a prominent element in the optics industry, significantly enhancing the lifestyle and observing power of humans. However, no established standards exist for tolerances and definitions in this field. Advanced manufacturing technologies and metrology have been developed to fabricate modern freeform optics and meet the demands of various applications.

INTERNATIONAL JOURNAL OF EXTREME MANUFACTURING (2022)

Add to Collection

Article Materials Science, Ceramics

Effect of gradient design on the mechanical property and friction performance of nano self-lubricating ceramic cutting tool material

Mingdong Yi et al.

Summary: A gradient nano self-lubricating ceramic cutting tool material was prepared, exhibiting improved mechanical properties and wear resistance due to the designed gradient composition and the presence of residual compressive stresses in the surface layer.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Review Green & Sustainable Science & Technology

Eco-Friendly Cutting Fluids in Minimum Quantity Lubrication Assisted Machining: A Review on the Perception of Sustainable Manufacturing

Binayak Sen et al.

Summary: This paper summarizes previous research articles on minimum quantity lubrication (MQL) assisted machining, highlighting the shift towards sustainability that prompts researchers to reconsider the effects of different lubrication methods on machining. Recent studies suggest that the use of vegetable oil, nanofluids, and nanoplatelets in MQL system outperforms traditional lubrication technology in terms of machining performance. These findings demonstrate the environmentally friendly nature of MQL technology as a viable alternative to flood lubrication.

INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING-GREEN TECHNOLOGY (2021)

Add to Collection

Article Engineering, Manufacturing

Creep feed grinding induced gradient microstructures in the superficial layer of turbine blade root of single crystal nickel-based superalloy

Qing Miao et al.

Summary: The study investigated the surface deformation structures of turbine blade root of single crystal nickel-based superalloy produced under different creep feed grinding conditions, revealing gradient microstructures in the superficial layer. The formation of such gradient microstructures was found to be related to the graded variations in the plastic strain and strain rate induced in the creep feed grinding process.

INTERNATIONAL JOURNAL OF EXTREME MANUFACTURING (2021)

Add to Collection

Article Engineering, Multidisciplinary

Multilayer-growth of TiAlN/WS self-lubricating composite coatings with high adhesion and their cutting performance on titanium alloy

Guojian Li et al.

Summary: The TiAlN/WS self-lubricating composite coating effectively reduces the coefficient of friction and improves wear resistance during cutting, significantly extending tool life and enhancing cutting quality. This coating performs exceptionally well in difficult-to-cut materials, especially under dry cutting conditions.

COMPOSITES PART B-ENGINEERING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Dual textured carbide tools for dry machining of titanium alloys

Amal S. Siju et al.

Summary: During dry machining of titanium alloys, texturing of the tool rake surface can reduce cutting and thrust forces, decrease workpiece adhesion, and minimize built-up-edge formation, resulting in almost continuous chips with thin segmentation.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Fabrication, tribological properties and cutting performances of high-quality multilayer graded MCD/NCD/UNCD coated PCB end mills

Hua Wang et al.

Summary: The study focused on improving the surface smoothness and tool durability while machining 5G PCB material by using UNCD coating on PCB end mills. Different diamond coatings were compared for their adhesion levels, tribological properties, and wear performances, with UNCD/MCD/NCD coating showing outstanding results in reducing friction and enhancing wear resistance.

DIAMOND AND RELATED MATERIALS (2021)

Add to Collection

Article Materials Science, Coatings & Films

Greater improvement of carbon and boron co-doping on the mechanical properties, wear resistance and cutting performance of AlTiN coating than that of doping alone

Fangsheng Mei et al.

Summary: This study investigated the effects of carbon and boron co-doping on AlTiN coatings, showing that co-doping improves properties such as hardness and wear rate. The AlTiBCN coating exhibited the best adhesion, while tools coated with AlTiB0.02C0.005N showed the best cutting performance.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection

Article Engineering, Manufacturing

Surface modification of ultrahigh strength 300M steel under supercritical carbon dioxide (scCO2)-assisted grinding process

Jiaqiang Dang et al.

Summary: This study evaluated the surface modification of 300M steel material under the scCO(2)-assisted grinding process and compared the surface quality of different processing techniques. The results showed that the scCO(2)-assisted grinding process can produce smoother surface profiles and superior grain and carbide refinement compared to other methods.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Manufacturing

A novel approach to determine the velocity dependency of the friction behavior during machining by means of digital particle image velocimetry (DPIV)

Berend Denkena et al.

Summary: The current state of the art shows that the friction behavior during machining is not yet fully understood, requiring further research. A novel method for analyzing friction mechanisms in machining was proposed in this study, revealing a significant influence of the sliding velocity of the chip on the coefficient of friction across a wide range of coating properties and cutting velocities.

CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2021)

Add to Collection

Article Engineering, Civil

Influence of ultrasonic vibration-assisted cutting on ploughing effect in cutting Ti6Al4V

Feiyang Chen et al.

Summary: The study utilized the finite element method to investigate the ploughing effect of ultrasonic vibration-assisted cutting Ti6Al4V. The research focused on establishing mechanical models of the ploughing area and verified the correctness of the analysis model. Results indicate that ultrasonic vibration-assisted cutting can significantly reduce ploughing force and temperature, therefore decreasing tool wear and plastic deformation of the machined surface.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2021)

Add to Collection

Article Engineering, Industrial

Prediction of residual stress with multi-physics model for orthogonal cutting Ti-6Al-4V under various tool wear morphologies

Xiaoliang Liang et al.

Summary: The study proposed a multi-physics model considering the impact of tool wear on tool geometrical alterations to predict residual stress distribution in orthogonal turning Ti-6Al-4 V. Experimental results confirmed the effectiveness of the model under tool wear conditions, providing a novel method for controlling residual stress distribution through monitoring tool wear morphology.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection

Article Engineering, Mechanical

Friction and cutting characteristics of micro-textured diamond tools fabricated with femtosecond laser

Qingwei Wang et al.

Summary: Experimental results show that micro-textured diamond tools significantly reduce cutting forces and friction coefficients, except for concentric circular texture. Additionally, the cutting performance of single-crystal diamond tools is effectively improved with the application of micro-textures.

TRIBOLOGY INTERNATIONAL (2021)

Add to Collection

Review Engineering, Mechanical

Synergetic effects of surface texturing and solid lubricants to tailor friction and wear - A review

Andreas Rosenkranz et al.

Summary: Surface texturing and solid lubricants can significantly reduce friction and wear under dry conditions, and their synergistic effect has advantages in tribological performance. The article summarizes the latest research progress on surface texturing and solid lubricants, discusses the synergy between them, highlights the underlying mechanisms, identifies gaps in the existing understanding, and suggests opportunities for future research.

TRIBOLOGY INTERNATIONAL (2021)

Add to Collection

Article Engineering, Mechanical

Investigation of the tribological properties of Ti-TiN-(Ti,Al,Nb,Zr)N composite coating and its efficiency in increasing wear resistance of metal cutting tools

Sergey Grigoriev et al.

Summary: Raising temperature significantly decreases the adhesion component of the friction coefficient for coated samples, leading to internal cracking and delamination. Increasing cutting speed results in greater diffusion depth of coating elements and a slight decrease in the adhesion component of the friction coefficient.

TRIBOLOGY INTERNATIONAL (2021)

Add to Collection

Article Green & Sustainable Science & Technology

Effects of Physicochemical Properties of Different Base Oils on Friction Coefficient and Surface Roughness in MQL Milling AISI 1045

Qingan Yin et al.

Summary: Research found that palm oil showed the best lubrication effect among different vegetable oils, achieving the lowest milling force, friction coefficient, and surface roughness values, resulting in the smoothest workpiece surface. Analysis revealed that palm oil, with a high content of saturated fatty acids, high viscosity, and small contact angle, could form the strongest lubricating oil film at the tool-workpiece interface.

INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING-GREEN TECHNOLOGY (2021)

Add to Collection

Article Engineering, Aerospace

Feasibility study of creep feed grinding of 300M steel with zirconium corundum wheel

Jiaqiang DANG et al.

Chinese Journal of Aeronautics (2021)

Add to Collection

Article Engineering, Manufacturing

Tool wear induced the gradient distribution of surface integrity with process-microstructure-property characteristics after turning Ti-6Al-4 V

Xiaoliang Liang et al.

Summary: This study investigates the impact of tool wear on surface integrity in high-speed machining, analyzing microstructural evolution and mechanical behaviors to consider depth gradient surface integrity issues. Results show gradient distribution of fiber texture and phase compositions from surface to substrate, with surface tensile stress and peak compressive stress enhancing progressively with initial wear state.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Manufacturing

In situ imaging based thermo-mechanical analysis of built-up edge in cutting process

Dong Zhang et al.

Summary: This study successfully carried out a real-time thermo-mechanical analysis of the influences of BUE on the metal cutting process, including the identification of BUE and chip morphologies, as well as the kinematic field during the cutting process using high-speed filming and digital imaging correlation technique. Experimental observations revealed that a cutting speed of 120 m/min has the least influence on the cutting process.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Manufacturing

Coupled thermo-mechanical sticking-sliding friction model along tool-chip interface in diamond cutting of copper

Shiquan Liu et al.

Summary: This study presents an improved sticking-sliding friction model for diamond cutting, considering the dynamic evolution of thermo-mechanical friction stress at the tool-chip interface. Analytical investigation and experimental evaluation reveal the impact of cutting temperature on tool-chip friction states, and analyze the effects of depth of cut and rake angle on friction.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Manufacturing

Machining of hard materials using textured tool with minimum quantity nano-green cutting fluid

Kishor Kumar Gajrani et al.

Summary: The combination of rake face micro-textured cutting tool with indigenously synthesized nano-green cutting fluids under in-house developed minimum quantity cutting fluid (MQCF) environment significantly improves hard machining performance, reducing cutting forces, workpiece surface roughness, and improving chip morphology compared to untextured cutting tools.

CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2021)

Add to Collection

Article Automation & Control Systems

Effect of surface line/regular hexagonal texture on tribological performance of cemented carbide tool for machining Ti-6Al-4V alloys

Kairui Zheng et al.

Summary: In this study, different textured tools were used in the cutting process of Ti-6Al-4V alloy to analyze cutting force, tool wear morphology, and friction coefficient. It was found that tools with texture surface show lower cutting force, smoother wear morphology, and reduced friction coefficient, providing new insights for monitoring tool wear during cutting process.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)

Add to Collection

Review Engineering, Manufacturing

Advancements in material removal mechanism and surface integrity of high speed metal cutting: A review

Bing Wang et al.

Summary: This paper reviews the research and application of high speed metal cutting (HSMC) with a focus on material removal mechanism, cutting force and temperature variations, and summarizes the advantages and shortcomings of HSMC.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2021)

Add to Collection

Article Engineering, Industrial

Material removal mechanism of FCC single-crystalline materials at nano-scales: Chip removal & ploughing

Huan Liu et al.

Summary: An analytical model was proposed to predict the chip thickness and ploughing width for FCC crystal materials under arbitrary crystal orientations in nano-machining. The results indicate that the crystal orientation determines the transformation between chip removal and ploughing, offering insights into the machining mechanisms for FCC crystals at the nanoscale.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Coatings & Films

Surface integrity and wear behavior of 300M steel subjected to ultrasonic surface rolling process

Jiaqiang Dang et al.

Summary: The influences of ultrasonic surface rolling process (USRP) on the surface integrity and wear resistance of 300M steel samples were comprehensively studied. Results indicated that a 10-pass USRP treatment can significantly improve the surface integrity and enhance the wear resistance of 300M steel by about 30.9%. However, the improvements tend to be saturated along with the increase of processing passes.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Coatings & Films

Improvement on the mechanical, tribological properties and cutting performance of AlTiN-based coatings by compositional and structural design

Huadong Zhang et al.

Summary: AlTiSiN multi-layered coatings show promise for processing difficult-to-machine materials, with AlTiSiN G-3 exhibiting the best mechanical and tribological properties. Additionally, the oxidation resistance of the coatings follows the order of AlTiSiN G-1 > AlTiSiN G-2 > AlTiSiN G-3 > AlTiN.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection

Article Engineering, Manufacturing

On the microstructural evolution pattern of 300 M steel subjected to surface cryogenic grinding treatment

Jiaqiang Dang et al.

Summary: In this study, an ultrahigh strength 300 M steel was subjected to surface plastic deformation treatment using surface cryogenic grinding treatment (SCGT) technique. The microstructural evolution began with the formation of dislocation structures, followed by the development of ultrafine laminates and grains. SCGT induced a very high strain rate and strain gradient, leading to the transformation of martensite-matrix lamella into nanosized grains. The increase in grain size from nanoscale to microscale resulted in a significant decrease in microhardness.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Manufacturing

Investigation of the friction coefficient evolution and lubricant breakdown behaviour of AA7075 aluminium alloy forming processes at elevated temperatures

Xiao Yang et al.

Summary: The lubricant behavior at elevated temperatures was investigated through pin-on-disc tests between P20 tool steel and AA7075 aluminum alloy. The evolution of the coefficient of friction (COF) was observed to consist of three distinct stages with different friction mechanisms, influenced by temperature, contact pressure, and sliding speed. In the final stage, lubricant breakdown occurred due to increased temperature, contact pressure, sliding speed, and decreased initial lubricant volume, leading to high friction values at the interface.

INTERNATIONAL JOURNAL OF EXTREME MANUFACTURING (2021)

Add to Collection

Review Engineering, Manufacturing

Towards understanding the brittle-ductile transition in the extreme manufacturing

Tao Zhang et al.

Summary: This paper reviews the brittle-ductile transition (BDT) in extreme manufacturing, analyzes the factors affecting it, and discusses the mechanisms behind it. It suggests that the competition between plastic deformation and crack propagation determines the transition between brittleness and ductility. The brittleness or ductility of the machined material should be regulated by deformation scale, deformation temperature, and machining speed to benefit specific manufacturing processes.

INTERNATIONAL JOURNAL OF EXTREME MANUFACTURING (2021)

Add to Collection

Article Engineering, Manufacturing

Challenges in laser-assisted milling of titanium alloys

Matthew S. Dargusch et al.

Summary: Detailed studies on laser-assisted machining (LAM) of titanium alloys have revealed the positive impact of laser preheating on reducing cutting forces and improving productivity, as well as the detrimental effect of LAM on tool life. The research evaluates common cutting tools with different coating types to determine their effect on tool wear mechanisms in the machining of titanium alloys, and suggests the need for the development of new cutting tools that are not affected by diffusion-controlled wear processes.

INTERNATIONAL JOURNAL OF EXTREME MANUFACTURING (2021)

Add to Collection

Article Multidisciplinary Sciences

Assessment of Tool Wear and Surface Integrity in Ductile Cutting Using a Developed Tool

Seyed Hasan Musavi et al.

Summary: The study compares the performance of micro-textured cutting tools to non-textured tools in machining aluminum alloys, finding that the micro-textured tool significantly improves surface quality and tool life while reducing wear and density of defective regions on the workpiece surface.

ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING (2021)

Add to Collection

Article Engineering, Mechanical

Friction characteristics of mechanically microtextured metal surface in dry sliding

Jun Shimizu et al.

TRIBOLOGY INTERNATIONAL (2020)

Add to Collection

Article Green & Sustainable Science & Technology

Cutting Performance of Tool with Continuous Lubrication at Tool-chip Interface

Tongkun Cao et al.

INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING-GREEN TECHNOLOGY (2020)

Add to Collection

Article Education, Scientific Disciplines

Analysis of critical negative rake angle and friction characteristics in orthogonal cutting of AL1060 and T2

Yanchun Ding et al.

SCIENCE PROGRESS (2020)

Add to Collection

Article Materials Science, Ceramics

New observations on wear characteristics of solid Al2O3/Si3N4 ceramic tool in high speed milling of additive manufactured Ti6Al4V

Jiaqiang Dang et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Materials Science, Ceramics

An integrative approach to coating/carbide substrate design of CVD and PVD coated cutting tools during the machining of austenitic stainless steel

Q. He et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Chemistry, Physical

Effect of high hardness and adhesion of gradient TiAlSiN coating on cutting performance of titanium alloy

Wenzhang Lu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Engineering, Manufacturing

Chip formation and hole quality in dry drilling additive manufactured Ti6Al4V

Weiwei Ming et al.

MATERIALS AND MANUFACTURING PROCESSES (2020)

Add to Collection

Article Chemistry, Physical

Mechanism of atomic and close-to-atomic scale cutting of monocrystalline copper

Wenkun Xie et al.

APPLIED SURFACE SCIENCE (2020)

Add to Collection

Article Engineering, Civil

Effect of material microstructure on tool wear behavior during machining additively manufactured Ti6Al4V

Jiaqiang Dang et al.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2020)

Add to Collection

Article Automation & Control Systems

Mechanical and cutting performance of cemented carbide tools with Cr/x/DLC composite coatings

Tianmei Hao et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Article Automation & Control Systems

Development and validation of a new friction model for cutting processes

Bingxiao Peng et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Article Engineering, Industrial

Temperature monitoring of the tool-chip interface for PCBN tools using built-in thin-film thermocouples in turning of titanium alloy

Tianxiang Li et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)

Add to Collection

Article Engineering, Manufacturing

Effect of novel hybrid texture tool on turning process performance in MQL machining of Inconel 718 superalloy

P. Sivaiah et al.

MATERIALS AND MANUFACTURING PROCESSES (2020)

Add to Collection

Article Engineering, Industrial

Novel cutting inserts with multi-channel irrigation at the chip-tool interface: Modelling, design and experiments

Zhirong Liao et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Review Automation & Control Systems

The heat partition into cutting tool at tool-chip contact interface during cutting process: a review

Guangchao Hao et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Coatings & Films

Investigations into friction and wear behavior of AlTiN and AlCrN coatings deposited on laser textured WC/Co using novel open tribometer tests

Sarvesh Kumar Mishra et al.

SURFACE & COATINGS TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Ceramics

A 2D finite element approach for predicting the machining performance of nanolayered TiAlCrN coating on WC-Co cutting tool during dry turning of AISI 1045 steel

Ch Sateesh Kumar et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Materials Science, Ceramics

Multi-pattern failure modes and wear mechanisms of WC-Co tools in dry turning Ti-6Al-4V

Xiaoliang Liang et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Engineering, Manufacturing

Modeling of variable friction and heat partition ratio at the chip-tool interface during orthogonal cutting of Ti-6Al-4V

Siddharam Mane et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection

Article Engineering, Manufacturing

Performance of CrCN-WS2 hard/soft composite coated tools in dry cutting of titanium alloys

Yunsong Lian et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection

Article Engineering, Manufacturing

Performance analysis of coated carbide tool in turning of Nimonic 80A superalloy under different cutting environments

Mustafa Gunay et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection

Article Chemistry, Physical

Influence of CaF2@Al2O3on Cutting Performance and Wear Mechanism of Al2O3/Ti(C,N)/CaF2@Al2O3Self-Lubricating Ceramic Tools in Turning

Shuai Zhang et al.

MATERIALS (2020)

Add to Collection

Article Engineering, Mechanical

Influence of the nanostructure of Ti-TiN-(Ti,Al,Cr)N multilayer composite coating on tribological properties and cutting tool life

Alexey Vereschaka et al.

TRIBOLOGY INTERNATIONAL (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Tool wear induced modifications of plastic flow and deformed material depth in new generated surfaces during turning Ti-6Al-4V

Xiaoliang Liang et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Engineering, Mechanical

Experimental investigation on the performance of MQL drilling of AISI 321 stainless steel using nano-graphene enhanced vegetable-oil-based cutting fluid

Amrit Pal et al.

TRIBOLOGY INTERNATIONAL (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Preparation of WC-TiC-Ni3Al-CaF2 functionally graded self-lubricating tool material by microwave sintering and its cutting performance

Siwen Tang et al.

HIGH TEMPERATURE MATERIALS AND PROCESSES (2020)

Add to Collection

Article Engineering, Mechanical

Influence of alumina/MWCNT hybrid nanoparticle additives on tribological properties of lubricants in turning operations

Anuj Kumar Sharma et al.

FRICTION (2019)

Add to Collection

Review Engineering, Multidisciplinary

State-of-the-art of surface integrity induced by tool wear effects in machining process of titanium and nickel alloys: A review

Xiaoliang Liang et al.

MEASUREMENT (2019)

Add to Collection

Article Engineering, Manufacturing

Experimental investigation on machinability of DMLS Ti6Al4V under dry drilling process

Jiaqiang Dang et al.

MATERIALS AND MANUFACTURING PROCESSES (2019)

Add to Collection

Article Engineering, Industrial

Thermal, rheological, wettability and hard machining performance of MoS2 and CaF2 based minimum quantity hybrid nano-green cutting fluids

Kishor Kumar Gajrani et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Grain refinement mechanism under high strain-rate deformation in machined surface during high speed machining Ti6Al4V

Xiang Xu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Engineering, Mechanical

Gradient architecture of Si containing layer and improved cutting performance of AlCrSiN coated tools

Fei Cai et al.

WEAR (2019)

Add to Collection

Article Engineering, Mechanical

Analysis of the coefficient of friction at the workpiece-tool interface in milling of high strength compacted graphite cast irons

L. R. R. da Silva et al.

WEAR (2019)

Add to Collection

Review Automation & Control Systems

A comprehensive review on minimum quantity lubrication (MQL) in machining processes using nano-cutting fluids

Zafar Said et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

Add to Collection

Article Engineering, Mechanical

Finite element modeling of friction at the tool-chip-workpiece interface in high speed machining of Ti6Al4V

Maohua Du et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2019)

Add to Collection

Article Green & Sustainable Science & Technology

Hard machining performance of indigenously developed green cutting fluid using flood cooling and minimum quantity cutting fluid

Kishor Kumar Gajrani et al.

JOURNAL OF CLEANER PRODUCTION (2019)

Add to Collection

Article Engineering, Mechanical

Theoretical and numerical modeling of tool-chip friction in ultrasonic-assisted turning

Mohammad Lotfi et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART E-JOURNAL OF PROCESS MECHANICAL ENGINEERING (2019)

Add to Collection

Article Engineering, Mechanical

Effect of conical micro-grooved texture on tool-chip friction property and cutting performance of WC-TiC/Co cemented carbide tools

Minghua Pang et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY (2019)

Add to Collection

Article Engineering, Mechanical

Estimation of the friction coefficient in turning process of metals through model experiment

Mohammad A. Chowdhury et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY (2018)

Add to Collection

Article Automation & Control Systems

Investigation of temperature distribution in orthogonal cutting through dual-zone contact model on the rake face

Esin Cakir et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Automation & Control Systems

Cutting performance of carbide tools with hybrid texture

Xiuqing Hao et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Automation & Control Systems

Tool life and workpiece surface integrity when turning an RR1000 nickel-based superalloy

R. Hood et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Automation & Control Systems

Analysis of tool-chip interface characteristics of self-lubricating tools with nanotextures and WS2/Zr coatings in dry cutting

Youqiang Xing et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Engineering, Manufacturing

Effect of tool wear evolution on chip formation during dry machining of Ti-6Al-4V alloy

Matthew S. Dargusch et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2018)

Add to Collection

Article Engineering, Mechanical

Modeling of plastic deformation induced by thermo-mechanical stresses considering tool flank wear in high-speed machining Ti-6Al-4V

Xiaoliang Liang et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2018)

Add to Collection

Article Engineering, Mechanical

Modeling and simulation of tool-chip interface friction in cutting Al/SiCp composites based on a three-phase friction model

Chunzheng Duan et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2018)

Add to Collection

Article Engineering, Mechanical

3D finite element investigations on textured tools with different geometrical shapes for dry machining of titanium alloys

Sarvesh Kumar Mishra et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2018)

Add to Collection

Article Engineering, Industrial

Cutting performance of textured polycrystalline diamond tools with composite lyophilic/lyophobic wettabilities

Xiuqing Hao et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)

Add to Collection

Article Engineering, Mechanical

Modeling of cutting force in MQL machining environment considering chip tool contact friction

Bikash Chandra Behera et al.

TRIBOLOGY INTERNATIONAL (2018)

Add to Collection

Article Engineering, Mechanical

Quantitative analysis of frictional behavior of cupronickel B10 at the tool-chip interface during dry cutting

Mohan Hao et al.

TRIBOLOGY INTERNATIONAL (2018)

Add to Collection

Article Engineering, Mechanical

Investigation of tool wear in the turning of Inconel 718 superalloy in terms of process performance and productivity enhancement

W. Grzesik et al.

TRIBOLOGY INTERNATIONAL (2018)

Add to Collection

Article Engineering, Mechanical

Environmental friendly hard machining performance of uncoated and MoS2 coated mechanical micro-textured tungsten carbide cutting tools

Kishor Kumar Gajrani et al.

TRIBOLOGY INTERNATIONAL (2018)

Add to Collection

Article Engineering, Chemical

Simulation of Sinuous Flow in Metal Cutting

A. S. Vandana et al.

TRIBOLOGY LETTERS (2018)

Add to Collection

Article Engineering, Mechanical

Control of tribofilm formation in dry machining of hardened AISI D2 steel by tuning the cutting speed

Junfeng Yuan et al.

WEAR (2018)

Add to Collection

Article Chemistry, Physical

Influences of Cutting Speed and Material Mechanical Properties on Chip Deformation and Fracture during High-Speed Cutting of Inconel 718

Bing Wang et al.

MATERIALS (2018)

Add to Collection

Article Engineering, Manufacturing

Tribological and machining characteristics of an electrostatic minimum quantity lubrication (EMQL) technology using graphene nano-lubricants as cutting fluids

Tao Lv et al.

JOURNAL OF MANUFACTURING PROCESSES (2018)

Add to Collection

Review Materials Science, Multidisciplinary

High-pressure coolant effect on the surface integrity of machining titanium alloy Ti-6Al-4V: a review

Wentao Liu et al.

MATERIALS RESEARCH EXPRESS (2018)

Add to Collection

Article Automation & Control Systems

Effect of symmetrical conical micro-grooved texture on tool-chip friction property of WC-TiC/Co cemented carbide tools

Minghua Pang et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Materials Science, Coatings & Films

Tribological behavior and cutting performance of monolayer, bilayer and multilayer diamond coated milling tools in machining of zirconia ceramics

Chengchuan Wang et al.

SURFACE & COATINGS TECHNOLOGY (2018)

Add to Collection

Article Engineering, Manufacturing

Effect of tool wear on chip formation during dry machining of Ti-6Al-4V alloy, part 1: Effect of gradual tool wear evolution

Shoujin Sun et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2017)

Add to Collection

Article Automation & Control Systems

Identification of a new friction model at tool-chip interface in dry orthogonal cutting

Chengyan Zhang et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)

Add to Collection

Article Automation & Control Systems

Investigating the influence of friction conditions on finite element simulation of microscale machining with the presence of built-up edge

Samad Nadimi Bavil Oliaei et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)

Add to Collection

Article Automation & Control Systems

Influence of friction models on FE simulation results of orthogonal cutting process

Amir Malakizadi et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)

Add to Collection

Article Automation & Control Systems

Friction, wear, and cutting tests on 022Cr17Ni12Mo2 stainless steel under minimum quantity lubrication conditions

Xu Chuangwen et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)

Add to Collection

Article Automation & Control Systems

Influence of cutter velocity, friction coefficient and rake angle on the formation of discontinuous rock fragments during rock cutting process

Pradeep L. Menezes

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)

Add to Collection

Article Automation & Control Systems

Impact of supply conditions of liquid nitrogen on tool wear and surface integrity when machining the Ti-6Al-4V titanium alloy

Y. Ayed et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)

Add to Collection

Article Automation & Control Systems

Experimental investigations on effects of tool flank wear on surface integrity during orthogonal dry cutting of Ti-6Al-4V

Xiaoliang Liang et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)

Add to Collection

Article Green & Sustainable Science & Technology

Surface texturing for tribology enhancement and its application on drill tool for the sustainable machining of titanium alloy

S. Niketh et al.

JOURNAL OF CLEANER PRODUCTION (2017)

Add to Collection

Article Green & Sustainable Science & Technology

Biodegradation and hard machining performance comparison of ecofriendly cutting fluid and mineral oil using flood cooling and minimum quantity cutting fluid techniques

Kishor Kumar Gajrani et al.

JOURNAL OF CLEANER PRODUCTION (2017)

Add to Collection

Article Engineering, Mechanical

Experimental study of the effect of coating thickness and substrate roughness on tool wear during turning

M. Bar-Hen et al.

TRIBOLOGY INTERNATIONAL (2017)

Add to Collection

Article Engineering, Mechanical

The role of PVD coating and coolant nature in wear development and tool performance in cryogenic and wet milling of Ti-6Al-4V

M. Ibrahim Sadik et al.

WEAR (2017)

Add to Collection

Article Engineering, Mechanical

Tool wear characterizations in finish turning of AISI 1045 carbon steel for MQCL conditions

Radoslaw W. Maruda et al.

WEAR (2017)

Add to Collection

Article Engineering, Mechanical

Sinuous flow and folding in metals: Implications for delamination wear and surface phenomena in sliding and cutting

Anirban Mahato et al.

WEAR (2017)

Add to Collection

Article Engineering, Mechanical

Experimental and theoretical study of the microscopic crater wear mechanism in titanium machining

S. Odelros et al.

WEAR (2017)

Add to Collection

Article Engineering, Manufacturing

Tool wear on nickel alloys with different coolant pressures: Comparison of Alloy 718 and Waspaloy

R. Polvorosa et al.

JOURNAL OF MANUFACTURING PROCESSES (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation of Coated Cutting Tool Performance during Machining of Super Duplex Stainless Steels through 3D Wear Evaluations

Yassmin Seid Ahmed et al.

COATINGS (2017)

Add to Collection

Article Engineering, Industrial

Advances in material and friction data for modelling of metal machining

Shreyes N. Melkote et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2017)

Add to Collection

Proceedings Paper Engineering, Industrial

Friction model for tool/work material contact applied to surface integrity prediction in orthogonal cutting simulation

L. A. Denguir et al.

16TH CIRP CONFERENCE ON MODELLING OF MACHINING OPERATIONS (16TH CIRP CMMO) (2017)

Add to Collection

Proceedings Paper Engineering, Industrial

Simulative investigations on different friction coefficient models

Frederik Zanger et al.

16TH CIRP CONFERENCE ON MODELLING OF MACHINING OPERATIONS (16TH CIRP CMMO) (2017)

Add to Collection

Article Automation & Control Systems

Tool wear mechanisms involved in crater formation on uncoated carbide tool when machining Ti6Al4V alloy

R. A. Rahman Rashid et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)

Add to Collection

Article Engineering, Manufacturing

Correlation Between Friction and Wear of Cubic Borone Nitride Cutting Tools in Precision Hard Machining

Wit Grzesik et al.

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2016)

Add to Collection

Article Mechanics

Some insights on the modelling of chip formation anditsmorphology during metal cutting operations

Tarek Mabrouki et al.

COMPTES RENDUS MECANIQUE (2016)

Add to Collection

Article Automation & Control Systems

Effect of hybrid texture combining micro-pits and micro-grooves on cutting performance of WC/Co-based tools

Jialin Sun et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)

Add to Collection

Article Engineering, Manufacturing

Effect of dynamic recrystallization at tool-chip interface on accelerating tool wear during high-speed cutting of AISI1045 steel

C. L. Pu et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2016)

Add to Collection

Article Engineering, Industrial

Development of a friction model and its application in finite element analysis of minimum quantity lubrication machining of Ti-6Al-4V

Nilanjan Banerjee et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)

Add to Collection

Article Engineering, Mechanical

Influence of Minimum Quantity Lubrication on Friction Characterizing Tool-Aluminum Alloy Contact

Frederic Cabanettes et al.

JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2016)

Add to Collection

Article Engineering, Manufacturing

Comparative investigation on using cryogenic machining in CNC milling of Ti-6Al-4V titanium alloy

Alborz Shokrani et al.

MACHINING SCIENCE AND TECHNOLOGY (2016)

Add to Collection

Article Engineering, Mechanical

Detecting the key geometrical features and grades of carbide inserts for the turning of nickel-based alloys concerning surface integrity

A. Fernandez-Valdivielso et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE (2016)

Add to Collection

Article Engineering, Mechanical

Influence of the machining parameters and cooling strategies on the wear behavior of wrought and additive manufactured Ti6Al4V for biomedical applications

S. Bruschi et al.

TRIBOLOGY INTERNATIONAL (2016)

Add to Collection

Article Engineering, Manufacturing

The influence of the cooling conditions on the cutting tool wear and the chip formation mechanism

Radoslaw W. Maruda et al.

JOURNAL OF MANUFACTURING PROCESSES (2016)

Add to Collection

Article Engineering, Manufacturing

Comparative Study of Turning of 4340 Hardened Steel with Hybrid Textured Self-Lubricating Cutting Inserts

Varun Sharma et al.

MATERIALS AND MANUFACTURING PROCESSES (2016)

Add to Collection

Article Chemistry, Physical

The friction coefficient evolution of a TiN coated contact during sliding wear

Guojia Ma et al.

APPLIED SURFACE SCIENCE (2015)

Add to Collection

Article Chemistry, Physical

Effect of microscale texture on cutting performance of WC/Co-based TiAlN coated tools under different lubrication conditions

Kedong Zhang et al.

APPLIED SURFACE SCIENCE (2015)

Add to Collection

Article Engineering, Industrial

Experimental and numerical assessment of subsurface plastic deformation induced by OFHC copper machining

J. C. Outeiro et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2015)

Add to Collection

Article Engineering, Industrial

On control of flow instabilities in cutting of metals

Dinakar Sagapuram et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2015)

Add to Collection

Article Engineering, Industrial

High performance cutting of advanced aerospace alloys and composite materials

Rachid M'Saoubi et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2015)

Add to Collection

Article Automation & Control Systems

A comparative study on cutting performance of rake-flank face structured cutting tool in orthogonal cutting of AISI/SAE 4140

Anis Fatima et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)

Add to Collection

Article Automation & Control Systems

Investigation of friction in end-milling of Ti-6Al-4V under different green cutting conditions

ZhiQiang Liu et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)

Add to Collection

Article Automation & Control Systems

Finite element modeling of hard turning process via a micro-textured tool

Dong Min Kim et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)

Add to Collection

Article Green & Sustainable Science & Technology

New observations on tool wear mechanism in machining Inconel 718 under water vapor plus air cooling lubrication cutting conditions

YiHang Fan et al.

JOURNAL OF CLEANER PRODUCTION (2015)

Add to Collection

Article Engineering, Manufacturing

Influence of High-Pressure Coolant Assistance on the Machinability of the Titanium Alloy Ti555-3

Tarek Braham-Bouchnak et al.

MACHINING SCIENCE AND TECHNOLOGY (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Modelling the tuned criticality in stick-slip friction during metal cutting

Q. Wang et al.

MODELLING AND SIMULATION IN MATERIALS SCIENCE AND ENGINEERING (2015)

Add to Collection

Article Computer Science, Interdisciplinary Applications

Numerical analysis of the formation of the dead metal zone with different tools in orthogonal cutting

Lei Wan et al.

SIMULATION MODELLING PRACTICE AND THEORY (2015)

Add to Collection

Article Materials Science, Coatings & Films

Comparison of TiN-coated tools using CVD and PVD processes during continuous cutting of Ni-based superalloys

Shuho Koseki et al.

SURFACE & COATINGS TECHNOLOGY (2015)

Add to Collection

Article Engineering, Mechanical

Effect of the local friction and contact nature on the Built-Up Edge formation process in machining ductile metals

S. Atlati et al.

TRIBOLOGY INTERNATIONAL (2015)

Add to Collection

Article Engineering, Mechanical

被撤回的出版物: Characterization of friction properties at the work material/cutting tool interface during the machining of randomly structured carbon fibers reinforced polymer with Poly Crystalline Diamond tool under dry conditions (Retracted article. See vol. 186, 2023)

Gregory Chardon et al.

TRIBOLOGY INTERNATIONAL (2015)

Add to Collection

Proceedings Paper Engineering, Manufacturing

The mechanics of cutting: In-situ measurement and modelling

Mustapha Abouridouane et al.

15TH CIRP CONFERENCE ON MODELLING OF MACHINING OPERATIONS (15TH CMMO) (2015)

Add to Collection

Article Engineering, Industrial

In-process measurement of friction coefficient in orthogonal cutting

D. Smolenicki et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2014)

Add to Collection

Article Automation & Control Systems

A new analytical tool-chip friction model in dry cutting

Fangjuan Zhou

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)

Add to Collection

Article Green & Sustainable Science & Technology

Identification of a friction model for minimum quantity lubrication machining

Nilanjan Banerjee et al.

JOURNAL OF CLEANER PRODUCTION (2014)

Add to Collection

Article Engineering, Mechanical

Experimental investigation on friction under metal cutting conditions

H. Puls et al.

WEAR (2014)

Add to Collection

Article Engineering, Mechanical

Cutting performance and wear characteristics of Al2O3/TiC ceramic cutting tools with WS2/Zr soft-coatings and nano-textures in dry cutting

Youqiang Xing et al.

WEAR (2014)

Add to Collection

Article Engineering, Mechanical

Determination of friction in metal cutting with tool wear and flank face effects

Wit Grzesik et al.

WEAR (2014)

Add to Collection

Review Engineering, Mechanical

Tribofilm Formation As a Result of Complex Interaction at the Tool/Chip Interface during Cutting

German S. Fox-Rabinovich et al.

LUBRICANTS (2014)

Add to Collection

Proceedings Paper Nanoscience & Nanotechnology

Potential of Size Reduction of Flat-plate Solar Collectors When Applying Al2O3 Nanofluid

M. Faizal et al.

NANOSCIENCE, NANOTECHNOLOGY AND NANOENGINEERING (2014)

Add to Collection

Proceedings Paper Engineering, Industrial

The Impact of Novel Material Processing Methods on Component Quality, Life and Performance

I. S. Jawahir et al.

PROCEEDINGS OF THE 3RD INTERNATIONAL CONFERENCE IN THROUGH-LIFE ENGINEERING SERVICES (2014)

Add to Collection

Article Engineering, Industrial

Characterisation of friction and heat partition coefficients at the tool-work material interface in cutting

J. Rech et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2013)

Add to Collection

Article Engineering, Industrial

Recent advances in modelling of metal machining processes

P. J. Arrazola et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Experimental investigation on the effect of the material microstructure on tool wear when machining hard titanium alloys: Ti-6Al-4V and Ti-555

M. Nouari et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2013)

Add to Collection

Article Engineering, Industrial

Determination of tool friction in presence of flank wear and stress distribution based validation using finite element simulations in machining of titanium and nickel based alloys

Durul Ulutan et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2013)

Add to Collection

Article Engineering, Mechanical

Influence of Minimum Quantity Lubrication on Friction Coefficient and Work-Material Adhesion During Machining of Cast Aluminum With Various Cutting Tool Substrates Made of Polycrystalline Diamond, High Speed Steel, and Carbides

Pierre Faverjon et al.

JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2013)

Add to Collection

Article Engineering, Multidisciplinary

Crater and flank wear resistance of cutting tools having micro textured surfaces

Tatsuya Sugihara et al.

PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2013)

Add to Collection

Article Engineering, Mechanical

Tribological behaviour of Ti6Al4V and Inconel718 under dry and cryogenic conditions-Application to the context of machining with carbide tools

C. Courbon et al.

TRIBOLOGY INTERNATIONAL (2013)

Add to Collection

Article Engineering, Mechanical

Influence of the tool surface micro topography on the tribological characteristics in metal cutting: Part I experimental observations of contact conditions

M. Fallqvist et al.

WEAR (2013)

Add to Collection

Article Engineering, Mechanical

Influence of the tool surface micro topography on the tribological characteristics in metal cutting-Part II Theoretical calculations of contact conditions

F. Schultheiss et al.

WEAR (2013)

Add to Collection

Article Engineering, Mechanical

Friction quantification in the oblique cutting with CBN chamfered tools

Wit Grzesik et al.

WEAR (2013)

Add to Collection

Article Engineering, Mechanical

Wear performance of (nc-AlTiN)/(a-Si3N4) coating and (nc-AlCrN)/(a-Si3N4) coating in high-speed machining of titanium alloys under dry and minimum quantity lubrication (MQL) conditions

Zhiqiang Liu et al.

WEAR (2013)

Add to Collection

Article Engineering, Mechanical

Tool-wear analysis in cryogenic machining of NiTi shape memory alloys: A comparison of tool-wear performance with dry and MQL machining

Y. Kaynak et al.

WEAR (2013)

Add to Collection

Article Engineering, Mechanical

Degradation modes and tool wear mechanisms in finish and rough machining of Ti17 Titanium alloy under high-pressure water jet assistance

Y. Ayed et al.

WEAR (2013)

Add to Collection

Article Engineering, Mechanical

Evaluation of the effect of application of cutting fluid at high pressure on tool wear during turning operation of AISI 316 austenitic stainless steel

V. T. G. Naves et al.

WEAR (2013)

Add to Collection

Article Thermodynamics

Inluence of cutting parameters, tool coatings and friction on the process heat in cutting processes and phase transformations in workpiece surface layers

V. Schulze et al.

HTM-JOURNAL OF HEAT TREATMENT AND MATERIALS (2013)

Add to Collection

Proceedings Paper Engineering, Multidisciplinary

Friction and Wear characteristics of WC and TiCN-coated Insert in Turning Carbon Steel Workpiece

R. J. Talib et al.

INTERNATIONAL TRIBOLOGY CONFERENCE MALAYSIA 2013 (2013)

Add to Collection

Article Engineering, Industrial

Surface integrity analysis of machined Inconel 718 over multiple length scales

Rachid M'Saoubi et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2012)

Add to Collection

Article Automation & Control Systems

Performance of the self-lubricating textured tools in dry cutting of Ti-6Al-4V

Wu Ze et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2012)

Add to Collection

Article Materials Science, Multidisciplinary

Friction and wear properties of TiN, TiAIN, AlTiN and CrAlN PVD nitride coatings

Liu Aihua et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2012)

Add to Collection

Article Engineering, Industrial

A comparison of cryogenic and high pressure emulsion cooling technologies on tool life and chip morphology in Ti-6Al-4V cutting

M. J. Bermingham et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2012)

Add to Collection

Review Materials Science, Multidisciplinary

Hierarchical adaptive nanostructured PVD coatings for extreme tribological applications: the quest for nonequilibrium states and emergent behavior

German S. Fox-Rabinovich et al.

SCIENCE AND TECHNOLOGY OF ADVANCED MATERIALS (2012)

Add to Collection

Proceedings Paper Engineering, Manufacturing

Machining of nodular cast iron (PF-NCI) using CBN tools

W. Grzesik et al.

FIFTH CIRP CONFERENCE ON HIGH PERFORMANCE CUTTING 2012 (2012)

Add to Collection

Article Engineering, Mechanical

Research on the dynamic mechanical characteristics and turning tool life under the conditions of excessively heavy-duty turning

Genghuang He et al.

FRONTIERS OF MECHANICAL ENGINEERING (2012)

Add to Collection

Article Engineering, Manufacturing

Molecular dynamics simulations of plastic material deformation in machining with a round cutting edge

Chang-Ju Kim et al.

INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING (2012)

Add to Collection

Article Engineering, Industrial

Surface integrity in material removal processes: Recent advances

I. S. Jawahir et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2011)

Add to Collection

Article Engineering, Industrial

Performance of electrical discharge textured cutting tools

P. Koshy et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2011)

Add to Collection

Article Engineering, Manufacturing

New observations on tool life, cutting forces and chip morphology in cryogenic machining Ti-6Al-4V

M. J. Bermingham et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2011)

Add to Collection

Article Engineering, Mechanical

Friction and wear behaviors of the carbide tools embedded with solid lubricants in sliding wear tests and in dry cutting processes

Deng Jianxin et al.

WEAR (2011)

Add to Collection

Article Engineering, Mechanical

Investigation of microstructured milling tool for deferring tool wear

Wenlong Chang et al.

WEAR (2011)

Add to Collection

Article Engineering, Manufacturing

Alginate microsphere fabrication using bipolar wave-based drop-on-demand jetting

C. Leigh Herran et al.

Journal of Manufacturing Processes (2011)

Add to Collection

Proceedings Paper Engineering, Manufacturing

A New Experimental Approach for Determination the Effect of Tool Flank Wear Length on Cutting Temperature Distributions

Lin Yan et al.

ADVANCED MANUFACTURING TECHNOLOGY, PTS 1, 2 (2011)

Add to Collection

Article Engineering, Manufacturing

Contact Conditions at the Chip-Tool Interface in Machining

Jihong Hwang et al.

INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING (2011)

Add to Collection

Article Engineering, Industrial

Improving anti-adhesive properties of cutting tool surfaces by nano-/micro-textures

T. Enomoto et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2010)

Add to Collection

Article Engineering, Mechanical

Investigations on the effects of friction modeling in finite element simulation of machining

Pedro J. Arrazola et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2010)

Add to Collection

Article Engineering, Manufacturing

Minor cutting edge-workpiece interactions in drilling of an advanced nickel-based superalloy

J. Kwong et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2009)

Add to Collection

Article Engineering, Manufacturing

Surface integrity of dry machined titanium alloys

A. Ginting et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2009)

Add to Collection

Article Engineering, Manufacturing

Analytical and experimental investigation of rake contact and friction behavior in metal cutting

Emre Ozlu et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2009)

Add to Collection

Article Engineering, Industrial

Identification of a friction model at tool/chip/workpiece interfaces in dry machining of AISI4142 treated steels

F. Zemzemi et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)

Add to Collection

Article Engineering, Multidisciplinary

Development of cutting tools with microscale and nanoscale textures to improve frictional behavior

Noritaka Kawasegi et al.

PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2009)

Add to Collection

Article Engineering, Mechanical

Tribological oxidation behaviour of PVD hard coatings

J. L. Mo et al.

TRIBOLOGY INTERNATIONAL (2009)

Add to Collection

Article Engineering, Manufacturing

ANALYSIS OF TRIBOLOGICAL PARAMETERS DURING MACHINING

S. Bahi et al.

INTERNATIONAL JOURNAL OF MATERIAL FORMING (2009)

Add to Collection

Article Engineering, Industrial

The effect of machinability on thermal fields in orthogonal cutting of AN 4140 steel

P. J. Arrazola et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2008)

Add to Collection

Article Engineering, Manufacturing

The effect of tool edge radius on the contact phenomenon of tool-based micromachining

K. S. Woon et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)

Add to Collection

Article Engineering, Manufacturing

A new material model for 2D numerical simulation of serrated chip formation when machining titanium alloy Ti-6Al-4V

Madalina Calamaz et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)

Add to Collection

Article Engineering, Manufacturing

A new approach for the friction identification during machining through the use of finite element modeling

P. J. Arrazola et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)

Add to Collection

Article Engineering, Manufacturing

Modelling tool wear in cemented-carbide machining alloy 718

J. Lorentzon et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)

Add to Collection

Article Engineering, Manufacturing

Modelling and analysis of micro scale milling considering size effect, micro cutter edge radius and minimum chip thickness

Xinmin Lai et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)

Add to Collection

Article Engineering, Manufacturing

Surface integrity and tool life when turning Inconel 718 using ultra-high pressure and flood coolant systems

A. R. C. Sharman et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2008)

Add to Collection

Article Engineering, Manufacturing

A critical analysis on the friction modelling in orthogonal machining

L. Filice et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2007)

Add to Collection

Article Engineering, Manufacturing

The influence of friction models on finite element simulations of machining

T Özel

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2006)

Add to Collection

Article Engineering, Mechanical

Friction modelling in metal cutting

THC Childs

WEAR (2006)

Add to Collection

Article Engineering, Manufacturing

The effect of cutting tool material and edge geometry on tool life and workpiece surface integrity

J. I. Hughes et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2006)

Add to Collection

Article Engineering, Industrial

Turning of advanced Ni based alloys obtained via powder metallurgy route

D. A. Axinte et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2006)

Add to Collection

Review Engineering, Manufacturing

Heat generation and temperature prediction in metal cutting: A review and implications for high speed machining

N. A. Abukhshim et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2006)

Add to Collection

Article Engineering, Industrial

The effect of machining on surface integrity of titanium alloy Ti-6% Al-4% V

CH Che-Haron et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2005)

Add to Collection

Article Engineering, Manufacturing

Analysis of the cutting force components and friction in high speed machining

G Sutter et al.

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2005)

Add to Collection

Article Engineering, Manufacturing

Research on experiments and action mechanism with water vapor as coolant and lubricant in Green cutting

JY Liu et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2005)

Add to Collection

Article Materials Science, Ceramics

Self-lubricating behaviors of Al2O3/TiB2ceramic tools in dry high-speed machining of hardened steel

JX Deng et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2005)

Add to Collection

Article Engineering, Manufacturing

A new thermomechanical model of cutting applied to turning operations. Part II. Parametric study

A Moufki et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2005)

Add to Collection

Article Engineering, Industrial

Modelling the effects of flank wear land and chip formation on residual stresses

L Chen et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2004)

Add to Collection

Article Engineering, Mechanical

A model for the contact conditions at the chip-tool interface in machining

B Ackroyd et al.

JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2003)

Add to Collection

Article Mathematics, Applied

A finite element study of the effect of friction in orthogonal metal cutting

GQ Shi et al.

FINITE ELEMENTS IN ANALYSIS AND DESIGN (2002)

Add to Collection

Article Materials Science, Coatings & Films

Friction and wear testing of multilayer coatings on carbide substrates for dry machining applications

W Grzesik et al.

SURFACE & COATINGS TECHNOLOGY (2002)

Add to Collection

Article Engineering, Industrial

Surface integrity of a high speed milled gamma titanium aluminide

AL Mantle et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)

Add to Collection

Article Engineering, Manufacturing

Friction and cutting forces in cryogenic machining of Ti-6Al-4V

SY Hong et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2001)

Add to Collection

Article Engineering, Manufacturing

Observations on chip formation and acoustic emission in machining Ti-6Al-4V alloy

J Barry et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2001)

Add to Collection

Article Engineering, Mechanical

The influence of thin hard coatings on frictional behaviour in the orthogonal cutting process

W Grzesik

TRIBOLOGY INTERNATIONAL (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.