Related references
Note: Only part of the references are listed.The Effect of Heat Accumulation on the Local Grain Structure in Laser-Directed Energy Deposition of Aluminium
Christian Hagenlocher et al.
METALS (2022)
In-situ digital image correlation and thermal monitoring in directed energy deposition additive manufacturing
James Haley et al.
OPTICS EXPRESS (2021)
Experimental and numerical thermal analysis of the laser powder bed fusion process using in situ temperature measurements of geometric primitives
Norman Schnell et al.
MATERIALS & DESIGN (2021)
Development of thermal model for the determination of SLM process parameters
Korhan Okten et al.
OPTICS AND LASER TECHNOLOGY (2021)
Effect of thermal cycling on microstructure and mechanical properties of 2A97 Al-Li alloy fabricated by direct laser deposition
Rui Chen et al.
VACUUM (2021)
Analytical Solution of the Non-Stationary Heat Conduction Problem in Thin-Walled Products during the Additive Manufacturing Process
Dmitrii Mukin et al.
MATERIALS (2021)
Process Window for Highly Efficient Laser-Based Powder Bed Fusion of AlSi10Mg with Reduced Pore Formation
Artur Leis et al.
MATERIALS (2021)
Microstructure by design: An approach of grain refinement and isotropy improvement in multi-layer wire-based laser metal deposition
M. Froend et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
Analytical modeling of in-process temperature in powder feed metal additive manufacturing considering heat transfer boundary condition
Jinqiang Ning et al.
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING-GREEN TECHNOLOGY (2020)
Numerical modelling of heat transfer and experimental validation in powder-bed fusion with the virtual domain approximation
Eric Neiva et al.
FINITE ELEMENTS IN ANALYSIS AND DESIGN (2020)
Modeling of thermal behavior and microstructure evolution during laser cladding of AlSi10Mg alloys
Chuanming Liu et al.
OPTICS AND LASER TECHNOLOGY (2020)
Dynamic Laser Absorptance Measured in a Geometrically Characterized Stainless-Steel Powder Layer
Brian J. Simonds et al.
PHYSICAL REVIEW APPLIED (2020)
Analytical Thermal Modeling of Powder Bed Metal Additive Manufacturing Considering Powder Size Variation and Packing
Jinqiang Ning et al.
MATERIALS (2020)
Melting modes in laser powder bed fusion
Sagar Patel et al.
MATERIALIA (2020)
Thermal histories and microstructures in Direct Energy Deposition of a High Speed Steel thick deposit
R. T. Jardin et al.
MATERIALS LETTERS (2019)
Keyhole threshold and morphology in laser melting revealed by ultrahigh-speed x-ray imaging
Ross Cunningham et al.
SCIENCE (2019)
Energy Coupling Mechanisms and Scaling Behavior Associated with Laser Powder Bed Fusion Additive Manufacturing
Jianchao Ye et al.
ADVANCED ENGINEERING MATERIALS (2019)
Analytical modeling of transient temperature in powder feed metal additive manufacturing during heating and cooling stages
Jinqiang Ning et al.
APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2019)
Analytical modeling of 3D temperature distribution in selective laser melting of Ti-6Al-4V considering part boundary conditions
Jinqiang Ning et al.
JOURNAL OF MANUFACTURING PROCESSES (2019)
Additive manufacturing of metallic components - Process, structure and properties
T. DebRoy et al.
PROGRESS IN MATERIALS SCIENCE (2018)
The full-field strain distribution and the evolution behavior during additive manufacturing through in-situ observation
Ruishan Xie et al.
MATERIALS & DESIGN (2018)
Impact of Interlayer Dwell Time on Microstructure and Mechanical Properties of Nickel and Titanium Alloys
B. K. Foster et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2017)
Processing constraints resulting from heat accumulation during pulsed and repetitive laser materials processing
Rudolf Weber et al.
OPTICS EXPRESS (2017)
Numerical simulation and experimental calibration of additive manufacturing by blown powder technology. Part I: thermal analysis
Michele Chiumenti et al.
RAPID PROTOTYPING JOURNAL (2017)
A Comprehensive Comparison of the Analytical and Numerical Prediction of the Thermal History and Solidification Microstructure of Inconel 718 Products Made by Laser Powder-Bed Fusion
Patcharapit Promoppatum et al.
ENGINEERING (2017)
In situ absorptivity measurements of metallic powders during laser powder-bed fusion additive manufacturing
Johannes Trapp et al.
APPLIED MATERIALS TODAY (2017)
Grain Structure Control of Additively Manufactured Metallic Materials
Fuyao Yan et al.
MATERIALS (2017)
2D modelling of clad geometry and resulting thermal cycles during laser cladding
Wei Ya et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)
Grain morphology evolution behavior of titanium alloy components during laser melting deposition additive manufacturing
T. Wang et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2015)
Effect of inter-layer dwell time on distortion and residual stress in additive manufacturing of titanium and nickel alloys
Erik R. Denlinger et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)
Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing
Wayne E. King et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)
Heat accumulation during pulsed laser materials processing
Rudolf Weber et al.
OPTICS EXPRESS (2014)
Share Paper
