☆ 4.6 Article

Characteristics of Gas-Solid Flow in an Intermittent Countercurrent Moving Bed

PROCESSES (2022)

Related references

Note: Only part of the references are listed.

Article Engineering, Chemical

Effect of a pulsating flow on hydrodynamics and fluid catalytic cracking chemical reaction in a circulating fluidized bed riser

Pilaiwan Chaiwang et al.

Summary: This study investigated the three-dimensional computational fluid dynamics (3D-CFD) of a pulsating flow applied to the fluid catalytic cracking (FCC) reaction in the riser of a circulating fluidized bed reactor. By considering the operating parameters of pulsating flow, it was found that frequency and type of the waveform significantly affect the reactant conversion level and product yield percentages.

PARTICUOLOGY (2022)

Add to Collection

Article Engineering, Chemical

Particle shape effect on hydrodynamics and heat transfer in spouted bed: A CFD-DEM study

E. Dianyu et al.

Summary: By investigating the effects of particle shape on hydrodynamics and heat transfer in a spouted bed, this study found that prolate spheroids form the largest bubbles and rise the highest, while oblate spheroids exhibit better heat transfer performance. Compared to spherical particles, ellipsoidal spheroids have better mobility and heat transfer efficiency.

PARTICUOLOGY (2022)

Add to Collection

Article Engineering, Chemical

DEM investigation of strain behaviour and force chain evolution of gravel-sand mixtures subjected to cyclic loading

Zhihong Nie et al.

Summary: The study used discrete element method to simulate the cyclic loading of gravel-sand mixtures with low fines contents, finding that increasing fines content accelerated the development of strain but had little effect on contact forces evolution. Strong contacts tended to develop along loading boundary with spatial differences, while weak contacts were initially controlled by confining pressure and then by axial stress.

PARTICUOLOGY (2022)

Add to Collection

Article Engineering, Chemical

Influence of the pressure drop and the air lock on the solid flux in a cross-flow moving bed

Ruojin Wang et al.

Summary: The gas-solid flow pattern in a rectangular cross-flow moving bed is simulated using the MP-PIC model with the Barracuda software and verified by experimental data. The study found that the actual solid flux in the bed is influenced significantly by the air lock and pressure drop in the solid feed and discharge tubes, rather than solely by valve openings as traditionally believed. The pressure drops in these tubes are calculated using the CPPMO and CPP methods, with gas resistance dominating the pressure drop in the solid discharge tubes and gas frictional resistance determining the pressure drop in the solid feed tube.

PARTICUOLOGY (2021)

Add to Collection

Article Engineering, Chemical

Experimental study on particle flow characteristics of three-dimensional moving bed

Lin Qiu et al.

POWDER TECHNOLOGY (2020)

Add to Collection

Article Engineering, Chemical

Modelling of dust emissions induced by flow over stockpiles and through packed beds

Daniel Schulz et al.

PARTICUOLOGY (2020)

Add to Collection

Article Engineering, Chemical

Hydrodynamics and solids mixing in fluidized beds with inclined-hole distributors

Alhussain Bakhurji et al.

PARTICUOLOGY (2019)

Add to Collection

Article Engineering, Chemical

Discrete and continuum modeling of granular flow in silo discharge

Tian Tian et al.

PARTICUOLOGY (2018)

Add to Collection

Article Engineering, Chemical

The influence of orifice shape on the flow rate: A DEM and experimental research in 3D hopper granular flows

Jiangfeng Wan et al.

POWDER TECHNOLOGY (2018)

Add to Collection

Review Engineering, Chemical

A review on gravity flow of free-flowing granular solids in silos - Basics and practical aspects

Khashayar Saleh et al.

CHEMICAL ENGINEERING SCIENCE (2018)

Add to Collection

Article Physics, Multidisciplinary

Investigation of flow rate in a quasi-2D hopper with two symmetric outlets

Xuezhi Zhang et al.

PHYSICS LETTERS A (2016)

Add to Collection

Article Engineering, Chemical

Numerical study on the behavior of funnel flow silos with and without inserts through a continuum hydrodynamic approach

Silvia Volpato et al.

CHEMICAL ENGINEERING RESEARCH & DESIGN (2014)

Add to Collection

Article Energy & Fuels

Impact of flow-corrective insert on flow patterns in two-dimensional moving bed

Shu-San Hsiau et al.

CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2013)

Add to Collection

Article Physics, Fluids & Plasmas

Geometry dependence of the clogging transition in tilted hoppers

C. C. Thomas et al.

PHYSICAL REVIEW E (2013)

Add to Collection

Article Engineering, Chemical

Simulation of dense granular flows: Dynamics of wall stress in silos

Riccardo Artoni et al.

CHEMICAL ENGINEERING SCIENCE (2009)

Add to Collection

Article Engineering, Chemical

Arch-Free flow in aerated silo discharge of cohesive powders

Antonio Cannavacciuolo et al.

POWDER TECHNOLOGY (2009)

Add to Collection

Article Engineering, Chemical

Gas pressure measurements inside an aerated hopper

G Donsi et al.

CHEMICAL ENGINEERING RESEARCH & DESIGN (2004)

Add to Collection

Article Engineering, Chemical

Gas flow maldistribution in moving beds of monosized particles

WR Paterson et al.

CHEMICAL ENGINEERING SCIENCE (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.