Related references
Note: Only part of the references are listed.Fabrication of Aluminum Tubes Filled with Aluminum Alloy Foam by Friction Welding
Yoshihiko Hangai et al.
MATERIALS (2015)
Enhanced mechanical properties of 70/30 brass joint by multi-pass friction stir welding with rapid cooling
N. Xu et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2015)
Dynamic and quasi-static bending behaviour of thin-walled aluminium tubes filled with aluminium foam
Isabel Duarte et al.
COMPOSITE STRUCTURES (2014)
Aluminum alloy foam core sandwich panels fabricated from die casting aluminum alloy by friction stir welding route
Yoshihiko Hangai et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)
Fabrication of Aluminum Foam-Filled Thin-Wall Steel Tube by Friction Welding and Its Compression Properties
Yoshihiko Hangai et al.
MATERIALS (2014)
Microstructural Characterization of Pure Copper Tubes Produced by A Novel Method Friction Stir Back Extrusion
I. Dinaharan et al.
INTERNATIONAL CONFERENCE ON ADVANCES IN MANUFACTURING AND MATERIALS ENGINEERING (ICAMME 2014) (2014)
Recent Trends in Aluminum Foam Sandwich Technology
John Banhart et al.
ADVANCED ENGINEERING MATERIALS (2012)
The influence of multi-pass friction stir processing on the microstructural and mechanical properties of Aluminum Alloy 6082
Magdy M. El-Rayes et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2012)
Nondestructive observation of pore structure deformation behavior of functionally graded aluminum foam by X-ray computed tomography
Yoshihiko Hangai et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
A preliminary study on the feasibility of friction stir back extrusion
Fadi Abu-Farha
SCRIPTA MATERIALIA (2012)
Effect of tool rotating rate on foaming properties of porous aluminum fabricated by using friction stir processing
Yoshihiko Hangai et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2010)
Axial Crushing Performance of Porous Aluminum Filled Members
Takeshi Hamada et al.
JOURNAL OF THE JAPAN INSTITUTE OF METALS (2009)
Effects of the Strain Rate and Alloying on the Compression Characteristics of Closed Cell Aluminum Foams
Takeshi Hamada et al.
MATERIALS TRANSACTIONS (2009)
Fabrication of Porous Aluminum by Friction Stir Processing
Yoshihiko Hangai et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2009)
Nondestructive Quantitative Evaluation of Porosity Volume Distribution in Aluminum Alloy Die Castings by Fractal Analysis
Yoshihiko Hangai et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2009)
Aluminium Foam Sandwich Panels: Manufacture, Metallurgy and Applications
John Banhart et al.
ADVANCED ENGINEERING MATERIALS (2008)
Improvement of mechanical properties of aluminum die casting alloy by multi-pass friction stir processing
K. Nakata et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Graded open-cell aluminium foam core sandwich beams
A Pollien et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2005)
Novel production for highly formable Mg alloy plate
YS Sato et al.
JOURNAL OF MATERIALS SCIENCE (2005)
Aluminium foams for lighter vehicles
J Banhart
INTERNATIONAL JOURNAL OF VEHICLE DESIGN (2005)
Joining techniques for aluminium spaceframes used in automobiles Part II - adhesive bonding and mechanical fasteners
TA Barnes et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2000)
Share Paper
