☆ 4.1 Article

Formability, Phase Composition, and Microstructure of TiC-(5-50 wt %) NiCr-Based Materials Obtained by Free SHS Compression

RUSSIAN JOURNAL OF INORGANIC CHEMISTRY (2022)

Related references

Note: Only part of the references are listed.

Article Metallurgy & Metallurgical Engineering

Ablation Casting of Thin-Wall Ductile Iron

E. Heidari et al.

Summary: An unalloyed thin-wall ductile cast iron was cast with different chemical compositions and commercial inoculants to investigate their effects on microstructure and mechanical properties. While ablation casting uses water for heat transfer, it did not impact the microstructure of the 1 mm thick casting.

INTERNATIONAL JOURNAL OF METALCASTING (2022)

Add to Collection

Article Chemistry, Inorganic & Nuclear

Preparation of Luminophore CaTiO3:Pr3+ by Self-Propagating High-Temperature Synthesis

O. B. Tomilin et al.

Summary: A self-propagating high-temperature synthesis of CaTiO3:Pr3+ luminophore samples was achieved using the thermal effect of the reaction between titanium and sodium perchlorate. The influence of different factors on the luminescent characteristics of the synthesized product was investigated.

RUSSIAN JOURNAL OF INORGANIC CHEMISTRY (2022)

Add to Collection

Review Materials Science, Ceramics

Laminated cermet composite materials: The main production methods, structural features and properties (review)

P. M. Bazhin et al.

Summary: This paper reviews the main production methods of laminated cermet composite materials, describing the basic methods for obtaining individual macrolayers and their consolidation methods, while considering the structure and physical and mechanical characteristics of the materials based on the production method.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Ceramics

Long-sized rods of Al2O3-SiC-TiB2 ceramic composite material obtained by SHS-extrusion: Microstructure, X-ray analysis and properties

Pavel Bazhin et al.

Summary: Long-sized rods of Al2O3-SiC-TiB2 ceramic composite material were successfully obtained by SHS-extrusion, showing a composite structure with uniform phase distribution. The material exhibited good heat resistance and hardness, indicating potential applications in the field of high-performance ceramics.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Structural features of layered composite material TiB2/TiAl/Ti6Al4 obtained by unrestricted SHS-compression

A. D. Prokopets et al.

Summary: By studying the preparation and properties of TiAl/TiB2-based composite materials, the hardness, structure, and phase composition of the material can be determined, achieving a gradual approach of the surface hardness of the alloy to the hardness of the alloy itself.

MATERIALS LETTERS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural and mechanical characteristics of direct laser welding 7075 super hard aluminum alloy/ D6AC ultra-high strength alloy structural steel

Yang Bao et al.

Summary: Through direct laser welding 7075 super-hard aluminum and D6AC super-high strength alloy structural steel, it was found that by setting specific laser parameters, the best joint formation can be achieved. However, brittle intermetallic compounds may form within the joints.

MATERIALS LETTERS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Dynamic observation of dislocation evolution and interaction with twin boundaries in silicon crystal growth using in - situ synchrotron X-ray diffraction imaging

M. G. Tsoutsouva et al.

Summary: In this study, the grown-in dislocation dynamics and interaction mechanisms with growth twins during the directional solidification of silicon crystals were investigated using X-ray Bragg diffraction imaging techniques. The research found that existing dislocations in the seed propagate in the up-grown crystal and are blocked by growth twins, but continue to move laterally behind the growth front.

ACTA MATERIALIA (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

An efficient method for iron ore sintering with high-bed layer: double-layer sintering

Qiang Zhong et al.

Summary: The double-layer sintering process (DLSP) efficiently addresses the issues of poor permeability and low sintering productivity in high-bed sintering, achieving high efficiency production by simultaneously sintering the upper and lower feed layers.

JOURNAL OF IRON AND STEEL RESEARCH INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of the Ar pressure on the structure of the NiTi foams produced by self-propagating high-temperature synthesis

N. Resnina et al.

Summary: Increasing Ar pressure affects the structure and martensitic transformation of NiTi foams produced by SHS. This is due to changes in combustion wave propagation and the decrease in transformation temperatures due to an increase in Ni concentration in the NiTi phase.

MATERIALS LETTERS (2021)

Add to Collection

Review Chemistry, Inorganic & Nuclear

Role of Mixing and Milling in Mechanochemical Synthesis (Review)

O. V. Lapshin et al.

Summary: The discussion includes various topics on inorganic mechanochemical synthesis, covering synthesis methods, monitoring techniques, yield control, kinetics, as well as comparisons between thermal and mechanochemical syntheses with a focus on mixing and milling processes. The effects of mechanical treatment on individual particles and mixtures, and the role of macrokinetics in mixing processes, are also examined. Additionally, the basic assumptions for a mathematical model describing the macrokinetics of mechanochemical synthesis in solid + reactive gas and solid + solid systems are outlined.

RUSSIAN JOURNAL OF INORGANIC CHEMISTRY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Consolidation and properties of tungsten by spark plasma sintering and hot isostatic pressing

Jong Min Byun et al.

Summary: The study attempted to fabricate dense tungsten using a combination process of spark plasma sintering and hot isostatic pressing, achieving an improvement in relative density and higher strength. X-ray diffractometry and X-ray photoelectron spectroscopy analysis revealed that the specimens were mainly composed of tungsten with trace amounts of metallic tungsten bound with oxygen. The strength testing showed promising results with biaxial bending test.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Room and High-Temperature Sliding Wear Behavior of In Situ TiC-Based Cermet Fabricated through Selective Laser Melting

Atefeh Aramian et al.

Summary: In this study, in situ TiC-NiCr cermet was fabricated using selective laser melting with different energy densities. Microstructural evaluation showed that lower energy densities led to non-uniform distribution of TiC and increased defects, while higher energy densities affected densification. The highest hardness was achieved at 378.2 J.mm(-3) energy density, but it decreased at higher values. Wear resistance improved slightly with increased energy density at room temperature, and the lowest wear rate was observed at 600 degrees C during elevated temperature testing.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection

Article Chemistry, Inorganic & Nuclear

Self-Propagating High-Temperature Synthesis of Ceramic Material Based on Aluminum-Magnesium Spinel and Titanium Diboride

A. P. Chizhikov et al.

Summary: The aim of this project is to synthesize ceramic composite materials based on aluminum-magnesium spinel strengthened by titanium diboride particles using the self-propagating high-temperature synthesis (SHS) method, and study their combustion characteristics, microstructure, and phase composition. It is found that changing the ratio of magnesium and aluminum in the composition results in changes in the phase composition of the synthesized products, and with an increase in combustion temperature, the morphology of the powder particles obtained with composite structures changes.

RUSSIAN JOURNAL OF INORGANIC CHEMISTRY (2021)

Add to Collection

Article Materials Science, Ceramics

Sintered Material Based on Titanium Carbide to Increase the Service Life of Slide Gates

M. S. Antipov et al.

Summary: A new cermet material based on titanium carbide with a complex binder has been obtained and studied for its optimal parameters using the SHS-extrusion method. The research shows that the microstructure, phase composition, and crystal lattice parameters of the obtained material do not change depending on the diameter of the extruded rod.

REFRACTORIES AND INDUSTRIAL CERAMICS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Structure and Mechanical Characteristics of a Laminated Ti3AlC2 MAX Phase-Based Composite Material Prepared by a Free Self-Propagating High-Temperature Synthesis Compression Method

A. D. Prokopets et al.

Summary: The research indicates that the time delay before exposure to pressure influences the structure and properties of Ti3AlC2 MAX phase-based laminated composite material.

INORGANIC MATERIALS (2021)

Add to Collection

Review Materials Science, Multidisciplinary

A review on recent developments of aluminum-based hybrid composites for automotive applications

Rohit Chandel et al.

Summary: The automotive sector is driven by the need for lightweight and efficient vehicles due to increased fuel costs and emission standards. Aluminum-based hybrid composites have been identified as promising alternatives to traditional alloys, with the potential to improve mechanical properties and reduce fuel consumption. The addition of reinforcement particles, both hard and soft, has been found to enhance strength, hardness, and wear resistance, demonstrating the potential for ceramic particulates and agricultural waste derivatives as secondary reinforcements.

EMERGENT MATERIALS (2021)

Add to Collection

Article Chemistry, Physical

Analysis of morphological, thermodynamic, and mechanical properties of typical hard phase Fe-5Cr-1.5B-0.45C alloy

Xiao-li Shi et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Self-Propagating High-Temperature Synthesis of MgAl2O4 Spinel

N. I. Radishevskaya et al.

INORGANIC MATERIALS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical and tribological properties of composite made of marble dust-reinforced C93200 copper alloy

Santosh Kumar Rajak et al.

MATERIALS RESEARCH EXPRESS (2020)

Add to Collection

Article Materials Science, Ceramics

Rapid fabrication of Al4SiC4 using a self-propagating high-temperature synthesis method

Yuki Nakashima et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Grain Size Reduction in a TiC-Co Material during SHS Extrusion

L. S. Stel'makh et al.

INORGANIC MATERIALS (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Tribological Characteristics and Corrosion Resistance of Coatings Obtained by Electrospark Alloying, Pulsed Cathodic Arc Evaporation, and Hybrid Technology Using TiCNiCr and TiCNiCr-Dy2O3Electrodes

A. D. Sytchenko et al.

RUSSIAN JOURNAL OF NON-FERROUS METALS (2020)

Add to Collection

Article Engineering, Mechanical

TiC-NiCr thermal spray coatings as an alternative to WC-CoCr and Cr3C2-NiCr

Giovanni Bolelli et al.

WEAR (2020)

Add to Collection

Article Materials Science, Ceramics

Nanostructured ceramic composite rods: Synthesis, properties and application

P. M. Bazhin et al.

CERAMICS INTERNATIONAL (2019)

Add to Collection

Article Physics, Condensed Matter

Effect of the Microstructure of Cermet Powders on the Performance Characteristics of Thermal Spray Coatings

A. E. Chesnokov et al.

JOURNAL OF SURFACE INVESTIGATION (2019)

Add to Collection

Article Materials Science, Ceramics

FREE SHS-COMPRESSION METHOD FOR PRODUCING LARGE-SIZED PLATES FROM CERAMIC MATERIALS

A. M. Stolin et al.

REFRACTORIES AND INDUSTRIAL CERAMICS (2019)

Add to Collection

Proceedings Paper Physics, Applied

Microstructure and Morphology of Powder Particles TiC-NiCr, Synthesized in Plasma Jet, at High-Energy Actions on Components of Initial Composition Ti-C-NiCr

Oleg P. Solonenko et al.

PROCEEDINGS OF THE XXV CONFERENCE ON HIGH-ENERGY PROCESSES IN CONDENSED MATTER (HEPCM 2017) (2017)

Add to Collection

Article Physics, Condensed Matter

Effect of the Microstructure of SHS Powders of Titanium Carbide-Nichrome on the Properties of Detonation Coatings

O. P. Solonenko et al.

JOURNAL OF SURFACE INVESTIGATION (2016)

Add to Collection

© Peeref 2019-2024. All rights reserved.