☆ 4.4 Article

Investigation of the scanning strategy on the microstructure and tensile property of Ti6Al4V alloy fabricated by selective laser melting

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE (2023)

Related references

Note: Only part of the references are listed.

Review Automation & Control Systems

Scanning strategy in selective laser melting (SLM): a review

Haolin Jia et al.

Summary: This paper reviews the impact of scanning strategies on the performance of 3D printed parts in additive manufacturing. It mainly focuses on the scanning strategies in the selective laser melting process and summarizes the effects of various scanning strategies. Suggestions for optimizing scanning strategies for better performance are provided based on the analysis.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)

Add to Collection

Article Automation & Control Systems

Optimization of selective laser melting process parameters for surface quality performance of the fabricated Ti6Al4V

Moses Oyesola et al.

Summary: This study investigates the influence of laser power and scanning speed on the surface hardness and roughness of Ti6Al4V metal specimens fabricated via selective laser melting. Results show that increasing laser power leads to higher surface hardness and lower roughness, while increasing scanning speed results in higher hardness and roughness. Optimal process parameters identified are a laser power of 300 W and a scan speed of 1400 mm/s, producing minimal surface roughness and a hardness value of 409.391 HV for aerospace applications.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Influence of hot isostatic pressing on microstructure, properties and deformability of selective laser melting TC4 alloy

Tai-qi Yan et al.

Summary: The study investigated the effect of different hot isostatic pressing regimes on the properties of TC4 alloy fabricated by selective laser melting technology. Results showed that the phase constitution and microstructure of the alloy changed after hot isostatic pressing, leading to a decrease in strength and hardness but an increase in ductility. The optimal hot isostatic pressing regime was found to be 940 degrees C/3 h/150 MPa, achieving a tensile strength of approximately 890 MPa and an elongation of around 14.0%.

CHINA FOUNDRY (2021)

Add to Collection

Article Optics

Study on performance optimization of 316L stainless steel parts by High-Efficiency Selective Laser Melting

Yude Liu et al.

Summary: The study increased the layer thickness and utilized a heat treatment process to improve the mechanical properties of specimens in the SLM process. By optimizing process parameters, different types of defects were identified and improvement methods were proposed.

OPTICS AND LASER TECHNOLOGY (2021)

Add to Collection

Article Chemistry, Physical

Directionally-Dependent Mechanical Properties of Ti6Al4V Manufactured by Electron Beam Melting (EBM) and Selective Laser Melting (SLM)

Tim Pasang et al.

Summary: A study was conducted to investigate the mechanical properties of Ti6Al4V produced by additive manufacturing compared to wrought alloys. Differences were found in microstructures, hardness, surface roughness, and tensile strength among the samples. The ductility of the wrought alloy was consistently higher than that of the additive manufactured Ti6Al4V.

MATERIALS (2021)

Add to Collection

Article Engineering, Chemical

Properties of 316L formed by a 400 W power laser Selective Laser Melting with 250 μm layer thickness

Wentian Shi et al.

POWDER TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

The effect of laser scanning strategies on texture, mechanical properties, and site-specific grain orientation in selective laser melted 316L SS

Jithin James Marattukalam et al.

MATERIALS & DESIGN (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Mapping the geometry of Ti-6Al-4V: From martensite decomposition to localized spheroidization during selective laser melting

Pere Barriobero-Vila et al.

SCRIPTA MATERIALIA (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of Scanning Strategy on the Performances of GO-Reinforced Ti6Al4V Nanocomposites Manufactured by SLM

Xiaojin Miao et al.

METALS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Experiment of Process Strategy of Selective Laser Melting Forming Metal Nonhorizontal Overhanging Structure

Wentian Shi et al.

METALS (2019)

Add to Collection

Article Automation & Control Systems

Limits and solutions in processing pure Cu via selective laser melting using a high-power single-mode fiber laser

Matteo Colopi et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

Add to Collection

Article Automation & Control Systems

Research on forming characteristic of pulsed selective laser melting

Bin Qi et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

Add to Collection

Article Automation & Control Systems

Rheological characterization of process parameters influence on surface quality of Ti-6Al-4V parts manufactured by selective laser melting

Amir Mahyar Khorasani et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Automation & Control Systems

High strain rate dynamic behaviour of AlSi12 alloy processed by selective laser melting

P. Ponnusamy et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Engineering, Industrial

Roughness modeling of AlSi10Mg parts fabricated by selective laser melting

Alberto Boschetto et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)

Add to Collection

Article Engineering, Biomedical

Fatigue behaviour of NiTi shape memory alloy scaffolds produced by SLM, a unit cell design comparison

M. Speirs et al.

JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2017)

Add to Collection

Article Multidisciplinary Sciences

3D printing of high-strength aluminium alloys

John H. Martin et al.

NATURE (2017)

Add to Collection

Article Engineering, Manufacturing

316L stainless steel mechanical and tribological behavior-A comparison between selective laser melting, hot pressing and conventional casting

F. Bartolomeu et al.

ADDITIVE MANUFACTURING (2017)

Add to Collection

Article Automation & Control Systems

Surface quality of the curved overhanging structure manufactured from 316-L stainless steel by SLM

Di Wang et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)

Add to Collection

Editorial Material Multidisciplinary Sciences

Materials creation adds new dimensions to 3D printing

Dongdong Gu

SCIENCE BULLETIN (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Processing and properties of topologically optimised biomedical Ti-24Nb-4Zr-8Sn scaffolds manufactured by selective laser melting

Y. J. Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Add to Collection

Article Automation & Control Systems

Balling behavior of stainless steel and nickel powder during selective laser melting process

Ruidi Li et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2012)

Add to Collection

Article Engineering, Mechanical

Factor analysis of selective laser melting process parameters and geometrical characteristics of synthesized single tracks

Igor Yadroitsev et al.

RAPID PROTOTYPING JOURNAL (2012)

Add to Collection

© Peeref 2019-2024. All rights reserved.