Related references
Note: Only part of the references are listed.UV laser high-quality drilling of CFRP plate with a new interlaced scanning mode
Wenyuan Li et al.
COMPOSITE STRUCTURES (2021)
Temperature-dependent material removal during pulsed laser processing of CFRP composites
Nengru Tao et al.
OPTICS AND LASER TECHNOLOGY (2021)
Feasibility study of wave-motion milling of carbon fiber reinforced plastic holes
Deyuan Zhang et al.
INTERNATIONAL JOURNAL OF EXTREME MANUFACTURING (2021)
An investigation of the effects of step drill geometry on drilling induced delamination and burr of Ti/CFRP stacks
Zhen-yuan Jia et al.
COMPOSITE STRUCTURES (2020)
Thermal defect characterization and strain distribution of CFRP laminate with open hole following fiber laser cutting process
Maojun Li et al.
OPTICS AND LASER TECHNOLOGY (2020)
Experimental Study on Surface Integrity and Kerf Characteristics During Abrasive Waterjet and Hybrid Machining of CFRP Laminates
Xujing Yang et al.
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING (2020)
Experimental investigation and optimization of abrasive water jet machining parameter on multi-walled carbon nanotube doped epoxy/carbon laminate
R. K. Thakur et al.
MEASUREMENT (2020)
Investigation of cut quality in fiber laser cutting of CFRP
Sehyeok Oh et al.
OPTICS AND LASER TECHNOLOGY (2019)
Influence of controlled depth abrasive water jet milling on the fatigue behavior of carbon/epoxy composites
Akshay Hejjaji et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2019)
Effects of processing parameters on kerf characteristics and surface integrity following abrasive waterjet slotting of Ti6Al4V/CFRP stacks
Maojun Li et al.
JOURNAL OF MANUFACTURING PROCESSES (2019)
Surface quality and kerf width prediction in abrasive water jet machining of metal-composite stacks
Rishi Pahuja et al.
COMPOSITES PART B-ENGINEERING (2019)
Study on burr occurrence and surface integrity during slot milling of multidirectional and plain woven CFRPs
Maojun Li et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Fiber laser cutting of CFRP laminates with single- and multi-pass strategy: A feasibility study
Maojun Li et al.
OPTICS AND LASER TECHNOLOGY (2018)
Critical thrust and feed prediction models in drilling of composite laminates
Navid Zarif Karimi et al.
COMPOSITE STRUCTURES (2016)
Heat conduction analysis of laser CFRP processing with IR and UV laser light
K. Takahashi et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2016)
Machining damage in FRPs: Laser versus conventional drilling
Akshay Hejjaji et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2016)
Delamination Characterization and Comparative Assessment of Delamination Control Techniques in Abrasive Water Jet Drilling of CFRP
Kamlesh Phapale et al.
44TH NORTH AMERICAN MANUFACTURING RESEARCH CONFERENCE, NAMRC 44 (2016)
Method of obtaining accurate jet lag information in abrasive water-jet machining process
Yuqiang Wu et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Experimental investigation of drilling damage and stitching effects on the mechanical behavior of carbon/epoxy composites
Yosra Turki et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2014)
Investigating the effect of machining processes on the mechanical behavior of composite plates with circular holes
M. Saleem et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2013)
A review of mechanical drilling for composite laminates
DeFu Liu et al.
COMPOSITE STRUCTURES (2012)
A study on UV laser drilling of PEEK reinforced with carbon fibers
L. Romoli et al.
OPTICS AND LASERS IN ENGINEERING (2012)
Machinability analysis in drilling woven GFR/epoxy composites: Part II - Effect of drill wear
U. A. Khashaba et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2010)
Influence of kinematic operating parameters on kerf geometry in abrasive waterjet machining of silicon carbide ceramics
D. S. Srinivasu et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2009)
Share Paper
