Related references
Note: Only part of the references are listed.Laser cutting of CFRP by Quasi-Continuous Wave (QCW) fibre laser: Effect of process parameters and analysis of the HAZ index
C. Leone et al.
COMPOSITES PART B-ENGINEERING (2021)
Study on laser drilling induced defects of CFRP plates with different scanning modes based on multi-pass strategy
Wenyuan Li et al.
OPTICS AND LASER TECHNOLOGY (2021)
Green Picosecond Laser Machining of Thermoset and Thermoplastic Carbon Fiber Reinforced Polymers
Insung Choi et al.
MICROMACHINES (2021)
Experimental and FE analysis for accurate measurement of deflection in CFRP and GFRP laminates under bending
Sajjad Seifoori et al.
MEASUREMENT (2020)
Whole-field strain analysis and strength prediction of fiber laser machined CFRP laminate at elevated temperature
Maojun Li et al.
POLYMER COMPOSITES (2020)
The influence of machining processes on strain distribution and progressive failure characteristics when producing holes in CFRP
Maojun Li et al.
COMPOSITE STRUCTURES (2020)
Factors influencing the tensile strength of carbon fiber reinforced plastic laminates for laser machining method and the underlined mechanisms
Yunxia Ye et al.
JOURNAL OF LASER APPLICATIONS (2020)
Experimental study on hole quality and tensile progressive failure following fiber laser cutting of multidirectional carbon fiber reinforced plastic laminates
Maojun Li et al.
JOURNAL OF LASER APPLICATIONS (2019)
Influence of controlled depth abrasive water jet milling on the fatigue behavior of carbon/epoxy composites
Akshay Hejjaji et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2019)
Thermal damage of CFRP laminate in fiber laser cutting process and its impact on the mechanical behavior and strain distribution
Maojun Li et al.
ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2019)
Influence of pulse repetition rate and pulse energy on the heat accumulation between subsequent laser pulses during laser processing of CFRP with ps pulses
C. Freitag et al.
APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2018)
Characterizing and modelling delamination of carbon-fiber epoxy laminates during abrasive waterjet cutting
J. Schwartzentruber et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2018)
Residual strength and damage mechanisms of laminated carbon fiber reinforced polymer under thermal environments and laser irradiations
Weina Zhao et al.
POLYMER ENGINEERING AND SCIENCE (2018)
A review on machinability of carbon fiber reinforced polymer (CFRP) and glass fiber reinforced polymer (GFRP) composite materials
Meltem Altin Karatas et al.
DEFENCE TECHNOLOGY (2018)
Machining damage in FRPs: Laser versus conventional drilling
Akshay Hejjaji et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2016)
Influence of laser scanning conditions on CFRP processing with a pulsed fiber laser
K. Takahashi et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)
An approach towards damage free machining of CFRP and GFRP composite material: a review
Dhiraj Kumar et al.
ADVANCED COMPOSITE MATERIALS (2015)
Surface and sub-surface degradation of unidirectional carbon fiber reinforced epoxy composites under dry and wet reciprocating sliding
H. Dhieb et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2013)
A review of mechanical drilling for composite laminates
DeFu Liu et al.
COMPOSITE STRUCTURES (2012)
Experimental study on the CO2 laser cutting of carbon fiber reinforced plastic composite
A. Riveiro et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2012)
A study on UV laser drilling of PEEK reinforced with carbon fibers
L. Romoli et al.
OPTICS AND LASERS IN ENGINEERING (2012)
Evaluation of Cutting Process on the Tensile and Fatigue Strength of CFRP Composites
Yoshihisa Harada et al.
THERMEC 2011, PTS 1-4 (2012)
Laser beam machining - A review
Avanish Kumar Dubey et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)
Investigations on the thermal effect caused by laser cutting with respect to static strength of CFRP
Dirk Herzog et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)
Analysis of parametric influence on delamination in high-speed drilling of carbon fiber reinforced plastic composites
V. N. Gaitonde et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Fibre reinforced composites in aircraft construction
C Soutis
PROGRESS IN AEROSPACE SCIENCES (2005)
Analysis and prediction of laser cutting parameters of fibre reinforced plastics (FRP) composite materials
AA Cenna et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2002)
Share Paper
