☆ 4.7 Article

Thermal analysis of a novel cycle for battery pre-warm-up and cool down for real driving cycles during different seasons

JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2023)

Related references

Note: Only part of the references are listed.

Article Thermodynamics

Experimental study of thermal management system for cylindrical Li-ion battery pack based on nanofluid cooling and copper sheath

Amirhosein Sarchami et al.

Summary: A novel thermal management system was developed and studied experimentally to control the temperature of cylindrical lithium-ion batteries. The study found that increasing the concentration of alumina nanoparticles and inflow velocity can significantly reduce the maximum temperature and temperature non-uniformity, while liquid cooling with stair channel can effectively reduce the temperature of the battery pack.

INTERNATIONAL JOURNAL OF THERMAL SCIENCES (2022)

Add to Collection

Article Energy & Fuels

Numerical and experimental investigation on electric vehicles battery thermal management under New European Driving Cycle

Mojtaba Safdari et al.

Summary: Optimizing the arrangement of the PCM-Air BTMS can enhance the cooling achievement of the battery pack under the NEDC. The use of different types of PCM depending on air velocity and driving distance is essential. Increasing PCM thickness and air gap appropriately can improve the battery temperature performance.

APPLIED ENERGY (2022)

Add to Collection

Article Thermodynamics

Surrogate model of liquid cooling system for lithium-ion battery using extreme gradient boosting

Chao Lyu et al.

Summary: This article proposes two innovations in surrogate modeling for BTMS structural optimization, which improve the efficiency and accuracy of BTMS structural optimization by considering operating conditions and using XGBoost model.

APPLIED THERMAL ENGINEERING (2022)

Add to Collection

Article Energy & Fuels

Nanofluid thermoelectric cooler based advanced battery thermal management system for battery degradation mitigation in real driving cycles

Hamed Khalili et al.

Summary: This study investigates a small-sized thermal management system based on nanofluid and thermoelectric elements to keep the battery pack temperature below 25 degrees C in electric vehicles. The introduction of two parameters, lithium-ion loss (LIL) and battery energy capacity fade (BECF), assesses the battery degradation. The system demonstrates lower energy consumption, better heat dissipation performance, longer battery life, and reduced pollution effects.

INTERNATIONAL JOURNAL OF ENERGY RESEARCH (2022)

Add to Collection

Article Energy & Fuels

Prediction of battery thermal behaviour in the presence of a constructal theory-based heat pipe (CBHP): A multiphysics model and pattern-based machine learning approach

Kittinan Boonma et al.

Summary: This study explores the thermal conductivity of a heat pipe based on constructal theory and combines it with a specialized form of machine learning and multiphysics numerical simulation to predict the thermal behavior of a lithium-ion battery during charging and discharging. The findings demonstrate that a heat pipe design grounded in constructal theory can lower the average and maximum temperatures of the battery, and the use of pattern-based machine learning significantly reduces training time and data transfer.

JOURNAL OF ENERGY STORAGE (2022)

Add to Collection

Article Energy & Fuels

Adaptive secondary loop liquid cooling with refrigerant cabin active thermal management system for electric vehicle

Srinivas Singirikonda et al.

Summary: A thermal management system is essential for electric vehicles to operate efficiently under different environmental conditions. This paper proposes a new battery thermal management system that controls the temperature of the battery and cabin, and effectively regulates temperature variations.

JOURNAL OF ENERGY STORAGE (2022)

Add to Collection

Article Energy & Fuels

Hybrid thermal management for achieving extremely uniform temperature distribution in a lithium battery module with phase change material and liquid cooling channels

S. Hekmat et al.

Summary: To enhance the performance and life span of a Li-ion battery module, it is essential to ensure a uniform temperature distribution. A novel hybrid battery thermal management system is proposed in this study, which can achieve a perfect temperature distribution under different discharge rates and coolant flow rates.

JOURNAL OF ENERGY STORAGE (2022)

Add to Collection

Article Energy & Fuels

An evaluation of the thermal behaviour of a lithium-ion battery pack with a combination of pattern-based artificial neural networks (PBANN) and numerical simulation

Mehrdad Mesgarpour et al.

Summary: This study conducted a numerical evaluation of the effects of battery cell and liquid-cooled channel configurations on thermal behavior, and introduced a physics-informed neural network and visual tracking technology to predict the thermal behavior of a battery package. Results show that evenly distributing cooling tubes can reduce the average temperature of the battery and phase change material, and the combination of liquid-cooling and phase change material can ensure that the battery temperature does not exceed limits.

JOURNAL OF ENERGY STORAGE (2022)

Add to Collection

Article Green & Sustainable Science & Technology

A new battery thermal management system employing the mini-channel cold plate with pin fins

Zengjia Guo et al.

Summary: A new battery thermal management system (BTMS) is proposed in this study, which utilizes a mini-channel cold plate with pin fins. The performance of the BTMS is evaluated using a 3D numerical model, and it is found that pin fins can improve heat transfer performance with acceptable pressure loss. The study also reveals that a staggered arrangement of pin fins outperforms an inline arrangement, and vertically arranged pin fins have higher performance compared to horizontally arranged pin fins.

SUSTAINABLE ENERGY TECHNOLOGIES AND ASSESSMENTS (2022)

Add to Collection

Article Energy & Fuels

Low-cost numerical lumped modelling of lithium-ion battery pack with phase change material and liquid cooling thermal management system

B. E. Lebrouhi et al.

Summary: This study develops a low cost lumped model for simulating a Li-ion battery pack with thermal management systems. The model uses transient energy balances and analogies between heat transfer and electrical transfer. Results show that combining phase change material and liquid cooling effectively reduces battery temperature.

JOURNAL OF ENERGY STORAGE (2022)

Add to Collection

Article Thermodynamics

Synergistic effect of insulation and liquid cooling on mitigating the thermal runaway propagation in lithium-ion battery module

Xinyu Rui et al.

Summary: This study investigated the synergy of heat dissipation and thermal insulation in the elimination of thermal runaway propagation (TRP) in Li-ion batteries of electric vehicles (EVs). It was found that pure liquid cooling alone is not effective in mitigating TRP, and successful inhibition of TRP requires the cooperation of thermal insulation and liquid cooling. Six critical conditions for TRP prevention were identified, and a theoretical diagram illustrating the relationship between heat dissipation and thermal insulation was obtained from modeling analysis.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

A new design for hybrid cooling of Li-ion battery pack utilizing PCM and mini channel cold plates

Sepehr Mousavi et al.

Summary: The paper introduces a novel battery thermal management system using phase change materials and mini-channel cold plates, showing that battery orientation significantly affects the cooling performance.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

Inclined U-shaped flat microheat pipe array configuration for cooling and heating lithium-ion battery modules in electric vehicles

Lin Liang et al.

Summary: The novel inclined U-shaped flat microheat pipe array (FMHPA) is used in the battery thermal management system to achieve high efficiency and space-saving. It reduces the maximum temperature and temperature difference of the module by 16% and 60% respectively, and maintains the heating rate within a suitable range. The FMHPAs effectively control the temperature rise rate and keep the module within the appropriate temperature range in various ambient temperatures.

ENERGY (2021)

Add to Collection

Article Chemistry, Physical

Design of cell spacing in lithium-ion battery module for improvement in cooling performance of the battery thermal management system

Kumar Kirad et al.

Summary: This study focuses on the thermal management of lithium-ion batteries by using forced air cooling for a battery module consisting of 30 batteries. Numerical models are built and validated for analysis of the cooling system, with a study on the effects of longitudinal and transverse spacing between batteries, as well as the flow velocity and discharge rate on thermal parameters. The research helps in selecting the optimal battery module spacing for improved cooling efficiency.

JOURNAL OF POWER SOURCES (2021)

Add to Collection

Article Thermodynamics

Topology optimization of cooling plates for battery thermal management

Xiaobao Mo et al.

Summary: A novel cooling plate was designed using the topology optimization method in this study, and numerical analysis showed significant improvements in reducing pressure drop and maximum temperature compared to traditional cooling plates. This approach could be considered as a high-efficiency method for battery thermal management.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2021)

Add to Collection

Article Thermodynamics

Experimental study on the thermal management of batteries based on the coupling of composite phase change materials and liquid cooling

Ziqiang Liu et al.

Summary: By utilizing a heat dissipation module based on a composite phase change material (CPCM) and liquid cooling, the thermal management of battery packs can be improved, making it more suitable for cyclic charging and discharging. Rapid realization of different heat dissipation solutions for battery pack modules with the coupling of CPCM and liquid cooling can be achieved by simply adjusting the hose connection. Furthermore, increasing the flow rate and decreasing the temperature of input cold water can enhance the heat dissipation effect of the battery pack.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

Experiment investigation on a novel composite silica gel plate coupled with liquid-cooling system for square battery thermal management

Yanrou Xu et al.

Summary: This study proposed a novel and effective hybrid cooling system combining composite silica gel plate (CSGP) with cooling tubes for battery module thermal management. The coupling of CSGP and copper tubes proved to be a feasible and effective method to control temperature with smaller temperature difference. The experimental results showed that the CSGP coupled with copper tubes can efficiently dissipate heat and control temperature, outperforming natural cooling and forced air convection methods.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

A novel liquid cooling plate concept for thermal management of lithium-ion batteries in electric vehicles

Mohsen Akbarzadeh et al.

Summary: This paper presents an innovative liquid cooling plate (LCP) embedded with phase change material (PCM) for thermal management of electric vehicle (EV) batteries. The hybrid LCP, combining active and passive cooling methods, is 36% lighter than traditional aluminum LCP and provides heating solution to slow temperature loss. Experimental and computational analyses show that the hybrid LCP reduces energy consumption and improves temperature uniformity, making it a promising thermal management solution for EVs.

ENERGY CONVERSION AND MANAGEMENT (2021)

Add to Collection

Article Thermodynamics

Investigation and optimization on cooling performance of a novel double helix structure for cylindrical lithium-ion batteries

Fei Dong et al.

Summary: In this study, a novel double helix cooling structure was designed for an 18650 lithium battery, and numerical simulation was used to investigate the effects of coolant mass flow rate, helix groove pitch, and flow diameter on cooling performance. By using Kriging approximate model method and Non-dominated Sorting Genetic Algorithm II, the optimal solutions were obtained. The results showed that increasing mass flow rate can effectively lower the maximum temperature of the battery within a certain range, while the pitch and diameter also have an impact on the cooling performance.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

A parametric study of a hybrid battery thermal management system that couples PCM/copper foam composite with helical liquid channel cooling

Huaqiang Liu et al.

Summary: A hybrid system combining PCM/copper foam with helical liquid channels was proposed and investigated numerically, showing more than 30 K temperature drop compared to natural convection. Various factors such as helical pitch, diameter, tube number, flow velocity, foam porosity, and pore density were studied to optimize battery temperature control.

ENERGY (2021)

Add to Collection

Article Thermodynamics

Thermodynamic analysis of a combined cycle of ammonia-based battery and absorption refrigerator

Shaozhi Zhang et al.

Summary: Heat-driven battery technology has been developing rapidly, with thermally regenerative ammonia-based batteries showing high power density. The combined cycle of TRAB and NH3/LiNO3/H2O absorption refrigerator demonstrated efficient operation in both refrigeration and battery modes, with evaluations on economic feasibility. The impact of operating factors and design parameters on system efficiency has been studied, offering potential for further research and optimization.

ENERGY (2021)

Add to Collection

Article Chemistry, Physical

Experimental investigation on the cooling and suppression effects of liquid nitrogen on the thermal runaway of lithium ion battery

Zonghou Huang et al.

Summary: The research shows that liquid nitrogen can effectively delay and suppress the thermal runaway of lithium ion batteries, significantly reducing the battery temperature in a short period of time. The cooling effect of liquid nitrogen becomes stronger as the application time increases.

JOURNAL OF POWER SOURCES (2021)

Add to Collection

Article Chemistry, Physical

Performance analysis on liquid-cooled battery thermal management for electric vehicles based on machine learning

Xingwang Tang et al.

Summary: This paper designs and analyzes the coupling system of liquid-cooled battery thermal management system (BTMS) and heat pump air conditioning system (HPACS) for battery electric vehicles (BEV). An automatic calibration model of the liquid-cooled BTMS based HPACS is established using support vector regression (SVR) to predict cooling capacity and system coefficient of performance, with particle swarm optimization (PSO) algorithm introduced to optimize the hyper parameters. The proposed PSO-SVR model shows improvement in correlation coefficient and reduction in mean squared error compared to the SVR model, indicating its potential as a new method to fit the complex nonlinear relationships among system COP, cooling capacity, and other influencing factors.

JOURNAL OF POWER SOURCES (2021)

Add to Collection

Article Thermodynamics

Novel hybrid thermal management for Li-ion batteries with nanofluid cooling in the presence of alternating magnetic field: An experimental study

Mehrdad Kiani et al.

Summary: This paper introduces a novel battery thermal management system composed of metal foam-paraffin PCM composite, nanofluid cooling, and heat sink, all under the influence of a magnetic field. Experimental simulations using a battery surrogate were conducted to study the effects of different conditions on paraffin wax melting and maximum battery temperature, resulting in a significantly improved hybrid BTMS with efficient heat dissipation.

CASE STUDIES IN THERMAL ENGINEERING (2021)

Add to Collection

Article Energy & Fuels

Effect analysis on performance enhancement of a novel and environmental evaporative cooling system for lithium-ion battery applications

Rekabra Youssef et al.

Summary: This study introduces a battery thermal management strategy using jute fiber as a cooling medium, which improves air cooling efficiency, temperature uniformity, and reduces equipment and weight. Experimental results support the effectiveness of this approach in enhancing battery thermal behavior.

JOURNAL OF ENERGY STORAGE (2021)

Add to Collection

Article Energy & Fuels

Investigation on battery thermal management system combining phase changed material and liquid cooling considering non-uniform heat generation of battery

Ping Ping et al.

Summary: A novel coupled thermal management system with phase change material (PCM) and liquid pipe was proposed and numerically investigated for maintaining the working temperature of a lithium-ion battery in the desired range under harsh conditions. The system exhibited good cooling performance, suppressing the maximum temperature and temperature difference of the battery pack, and effectively removing heat stored in PCM. Properly adjusting coolant velocity during charging was found to be feasible in saving power consumption while maintaining cooling capacity.

JOURNAL OF ENERGY STORAGE (2021)

Add to Collection

Article Thermodynamics

Performance evaluation of hybrid oscillating heat pipe with carbon nanotube nanofluids for electric vehicle battery cooling

Zhicheng Zhou et al.

Summary: This study developed a hybrid oscillating heat pipe using CNT nanofluids for cooling electric vehicle batteries, demonstrating improved heat transfer performance and reduced battery pack temperature.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

Numerical investigation of the direct liquid cooling of a fast-charging lithium-ion battery pack in hydrofluoroether

Xiaojun Tan et al.

Summary: This paper proposes a novel direct liquid battery cooling system for fast-charging battery packs based on a hydrofluoroether coolant. Through high-fidelity CFD simulations, it is found that optimizing channel design and coolant velocity can improve energy density and reduce power consumption, while a multilayer structure and cross-flowing configuration can reduce temperature difference and standard deviation.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

Numerical analysis and surrogate model optimization of air-cooled battery modules using double-layer heat spreading plates

Yefei Xu et al.

Summary: This paper investigates the air-cooled battery module with a thermally conductive heat spreading plate (HSP) and successfully enhances the cooling performance of the battery module through multi-objective optimization.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2021)

Add to Collection

Article Thermodynamics

A numerical study on thermal management of a lithium-ion battery module via forced-convective air cooling

Lalan K. Singh et al.

Summary: This study investigates the efficiency of heat removal in an air cooled battery module under different conditions, and finds that the number of cells in the module affects the maximum temperature, while the arrangement of cells has minimal influence on velocity and thermal field beyond a critical value.

INTERNATIONAL JOURNAL OF REFRIGERATION (2021)

Add to Collection

Article Thermodynamics

Numerical study of combined air and phase change cooling for lithium-ion battery during dynamic cycles

Yue Yang et al.

Summary: The study shows that the battery pack with combined forced convection and PCM cooling has better thermal performance, with both the maximum temperature and maximum temperature difference controlled within the ideal range. Additionally, at an ambient temperature of 26.5°C, the phase change temperature of 35°C is most advantageous for the thermal management system.

INTERNATIONAL JOURNAL OF THERMAL SCIENCES (2021)

Add to Collection

Article Chemistry, Physical

Active air cooling thermal management system based on U-shaped micro heat pipe array for lithium-ion battery

Ruyang Ren et al.

Summary: A new active air cooling thermal management system based on U-shaped micro heat pipe array has been developed, and comparative experiments have shown that it has the best cooling performance even under high charge and discharge rates.

JOURNAL OF POWER SOURCES (2021)

Add to Collection

Article Chemistry, Physical

Optimum cooling surface for prismatic lithium battery with metal shell based on anisotropic thermal conductivity and dimensions

Lin Liang et al.

Summary: The study investigates the optimal cooling surface for prismatic lithium battery based on anisotropic thermal conductivity, dimensions, and metal shell. Results show that increasing the thickness and area of aluminum shell can improve the cooling effect. Double surface cooling reduces the temperature rise by 24.1% compared with single surface cooling.

JOURNAL OF POWER SOURCES (2021)

Add to Collection

Article Energy & Fuels

Experimental and numerical investigation of the LiFePO4 battery cooling by natural convection

Orhan Kalkan et al.

Summary: The thermal performance of a LiFePO4 pouch type battery under different discharge rates was experimentally and numerically investigated. It was found that natural convection cooling is not sufficient for the battery at high discharge rates.

JOURNAL OF ENERGY STORAGE (2021)

Add to Collection

Article Energy & Fuels

Numerical study of novel liquid-cooled thermal management system for cylindrical Li-ion battery packs under high discharge rate based on AgO nanofluid and copper sheath

Mahdi Tousi et al.

Summary: A novel battery thermal management system based on AgO nanofluid is designed to maintain the maximum temperature and temperature homogeneity in 18650/21700 types lithium-ion batteries. The study shows that at high discharge rates, the use of optimal inflow velocity and nanofluid volume fraction as coolant can effectively reduce the temperature of the battery pack. Comparing the 18650 and 21700 types lithium-ion battery thermal management systems, the 21700 type battery pack shows promising potential.

JOURNAL OF ENERGY STORAGE (2021)

Add to Collection

Article Energy & Fuels

Numerical analysis of battery thermal management system coupling with low-thermal-conductive phase change material and liquid cooling

Junyi Niu et al.

Summary: Research compares the performance of BTMS in battery modules using LTC-PCM, LTCM, and HTCP. It further investigates the impact of different widths of LTC-PCM and flow rates of HTF. Results show that increasing LTC-PCM width reduces Tave, but the influence becomes minimal with flowing HTF.

JOURNAL OF ENERGY STORAGE (2021)

Add to Collection

Article Thermodynamics

A novel battery thermal management system coupling with PCM and optimized controllable liquid cooling for different ambient temperatures

Depeng Kong et al.

ENERGY CONVERSION AND MANAGEMENT (2020)

Add to Collection

Article Thermodynamics

Numerical evaluation of a thermal management system consisting PCM and porous metal foam for Li-ion batteries

Y. Salami Ranjbaran et al.

JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2020)

Add to Collection

Article Thermodynamics

Air and PCM cooling for battery thermal management considering battery cycle life

Fenfang Chen et al.

APPLIED THERMAL ENGINEERING (2020)

Add to Collection

Article Thermodynamics

Hybrid thermal management of lithium-ion batteries using nanofluid, metal foam, and phase change material: an integrated numerical-experimental approach

Mehrdad Kiani et al.

JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2020)

Add to Collection

Article Energy & Fuels

Life cycle cost analysis (LCCA) of PV-powered cooling systems with thermal energy and battery storage for off-grid applications

Christoph Luerssen et al.

APPLIED ENERGY (2020)

Add to Collection

Article Thermodynamics

Durability of phase-change-material module and its relieving effect on battery deterioration during long-term cycles

Youfu Lv et al.

APPLIED THERMAL ENGINEERING (2020)

Add to Collection

Article Thermodynamics

Heat-pipe based spray-cooling thermal management system for lithium-ion battery: Experimental study and optimization

Shurong Lei et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2020)

Add to Collection

Article Energy & Fuels

Experimental investigation on thermal performance of a battery liquid cooling structure coupled with heat pipe

Xuezhen Yuan et al.

JOURNAL OF ENERGY STORAGE (2020)

Add to Collection

Article Thermodynamics

Thermal modeling of full-size-scale cylindrical battery pack cooled by channeled liquid flow

Wenjiong Cao et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2019)

Add to Collection

Article Thermodynamics

The thermal performance of a novel internal cooling method for the electric vehicle battery: An experimental study

Jingren Gou et al.

APPLIED THERMAL ENGINEERING (2019)

Add to Collection

Article Green & Sustainable Science & Technology

Cooling performance of nanofluid submerged vs. nanofluid circulated battery thermal management systems

R. D. Jilte et al.

JOURNAL OF CLEANER PRODUCTION (2019)

Add to Collection

Article Thermodynamics

Water cooling based strategy for lithium ion battery pack dynamic cycling for thermal management system

Ke Li et al.

APPLIED THERMAL ENGINEERING (2018)

Add to Collection

Article Thermodynamics

Effects of the different air cooling strategies on cooling performance of a lithium-ion battery module with baffle

Jiaqiang E et al.

APPLIED THERMAL ENGINEERING (2018)

Add to Collection

Article Thermodynamics

A lumped thermal model of lithium-ion battery cells considering radiative heat transfer

Walid Allafi et al.

APPLIED THERMAL ENGINEERING (2018)

Add to Collection

Proceedings Paper Automation & Control Systems

Non-linear identification of a Peltier cell model using evolutionary multi-objective optimization

Victor Huilcapi et al.

IFAC PAPERSONLINE (2017)

Add to Collection

Article Electrochemistry

LIONSIMBA: A Matlab Framework Based on a Finite Volume Model Suitable for Li-Ion Battery Design, Simulation, and Control

Marcello Torchio et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2016)

Add to Collection

Article Thermodynamics

Heat transfer and thermal management with PCMs in a Li-ion battery cell for electric vehicles

N. Javani et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2014)

Add to Collection

Article Electrochemistry

Development of first principles capacity fade model for Li-ion cells

P Ramadass et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2004)

Add to Collection

Article Thermodynamics

Analytic model for transient heat exchanger response

J Yin et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2003)

Add to Collection

© Peeref 2019-2024. All rights reserved.