☆ 4.7 Article

Investigation on mechanical properties of AlON ceramics synthesized by spark plasma sintering

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2023)

Related references

Note: Only part of the references are listed.

Article Engineering, Multidisciplinary

Breaking through the dynamic strength-ductility trade-off in TiB reinforced Ti composites by incorporation of graphene nanoplatelets

Liang Liu et al.

Summary: Adjusting the three-dimensional reinforcement configuration by incorporating graphene nanoplatelets can overcome the strength-ductility incompatibility in titanium matrix composites. The addition of graphene nanoplatelets enhances both the dynamic strength and plasticity of the materials, while delaying the formation of adiabatic shear bands.

COMPOSITES PART B-ENGINEERING (2022)

Add to Collection

Article Physics, Applied

Comparisons of the Microstructure and Magnetic Properties of Anisotropic NdFeB Magnets Prepared by Hot Pressing and Spark Plasma Sintering

Xiang Li et al.

Summary: NdFeB hot-pressed and hot-deformed magnets were prepared by hot-pressed (HP) sintering and spark plasma sintering (SPS). The effects of different sintering mechanisms on the microstructure of the magnets were studied, revealing that the hot-deformed magnets prepared by HP have superior microstructural characteristics compared to those prepared by SPS, leading to significantly better comprehensive magnetic properties.

JOURNAL OF SUPERCONDUCTIVITY AND NOVEL MAGNETISM (2022)

Add to Collection

Article Materials Science, Ceramics

Fast one-step carbothermal reduction and nitridation method using nano-sized Al2O3 and carbon black to prepare aluminium oxynitride powder for highly transparent ceramics

Xiannian Sun et al.

Summary: A single-phase AlON powder was successfully synthesized using a fast one-step carbothermal reduction and nitridation method, showing potential for highly transparent AlON ceramics. By shortening the heating time, particle coarsening was significantly inhibited, resulting in the formation of small primary particle single-phase AlON powder.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Novel carbon nanotubes reinforced copper composite electrode for improved performance of electric discharge machining

J. Rajaguru et al.

Summary: Utilizing a Cu/CNT composite electrode in EDM machining can enhance Material Removal Rate and surface finish due to increased discharge energy and spark gap size, however, electrode wear may be accelerated due to reduced thermal conductivity caused by porosity effects.

MATERIALS LETTERS (2022)

Add to Collection

Article Nanoscience & Nanotechnology

A rapid route to improve the mechanical properties of the aged high Co-Ni steel

Xian-Yu Li et al.

Summary: SPS-forging was used to activate twins and produce fine omega phase in aged high Co-Ni steel. The M54 steel exhibited high tensile strength of 2054 +/- 24 MPa and good elongation of 12.6 +/- 1%.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Materials Science, Ceramics

Effect of Mo and TiC addition on the microstructure and mechanical properties of spark plasma sintered Si3N4 composites

Zhiyuan Ma et al.

Summary: This study aimed to enhance the fracture toughness of Si3N4 ceramics by adding TiC and Mo. The addition of TiC improved the hardness by inhibiting phase transformation and grain refinement. Meanwhile, Mo promoted phase transformation and formed molybdenum silicide, leading to improved fracture toughness. The Si3N4 composites with 8 wt% TiC and 8 wt% Mo exhibited optimal properties.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Review Chemistry, Multidisciplinary

Progress in Transparent Nano-Ceramics and Their Potential Applications

Wuyi Ming et al.

Summary: This study reviews the development trends and potential applications of transparent nano-ceramics in different fields, including laser nano-ceramic materials, magneto-optical transparent nano-ceramics, transparent armor nano-ceramic materials, electro-optical transparent nano-ceramics, and scintillation transparent nano-ceramics. The research results provide a meaningful reference for low-cost and sustainable production in the future.

NANOMATERIALS (2022)

Add to Collection

Article Materials Science, Ceramics

Transparent AlON ceramics by nitriding combustion synthesis precursors and pressureless sintering method

Yiming Zhang et al.

Summary: Fine AION powders with high sintering activities were synthesized, and high-transmittance AlON ceramics were achieved. The influences of different aluminum sources on precursors and nitride-functionalized products were studied. Al(NO3)(3) was found to be the most beneficial aluminum source for the preparation of active precursors and single-phase AlON powders. This research provides valuable reference for rapid preparation of AlON powders and transparent ceramics.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Ceramics

A comparison between a new Ultra Fast Pressureless Sintering (UFPS) technology and Spark Plasma Sintering (SPS) for Barium AluminoSilicate metastable phase

A. Allemand et al.

Summary: The SPS process is only suitable for manufacturing small hexagonal BAS components, while the UFPS technology can successfully process larger parts with better thermal control and eliminating the thermal gradient issue.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Transparent polycrystalline γ-AlON fabricated using a hybrid sintering process

Ayman Muhammad Tsabit et al.

Summary: This study reports on the properties of polycrystalline transparent gamma-AlON fabricated using a hybrid sintering process, aiming to reduce the time taken for the pressureless sintering process. The gamma-AlON fabricated using this hybrid process showed high optical transmittance, proving the feasibility of the method.

SCRIPTA MATERIALIA (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Direct achievement of ultra-high strength and good ductility for high Co-Ni secondary hardening steel by combining spark plasma sintering and deformation

Xianyu Li et al.

Summary: By combining spark plasma sintering and deformation, ultra-high strength steel with good ductility was successfully fabricated in this study. The martensite matrix produced by a distinctive mechanism in spark plasma sintering resulted in ultra-high strength of the specimens, while good ductility was observed in the specimens due to the gradual closing of micro-pores during SPS compression. The high Co-Ni steel produced achieved ultra-high strength and good ductility directly without the need for complicated traditional heat treatment processes.

MATERIALS LETTERS (2021)

Add to Collection

Article Chemistry, Physical

Mechanochemical Activation and Spark Plasma Sintering of the Lead-Free Ba(Fe1/2Nb1/2)O3 Ceramics

Dariusz Bochenek et al.

Summary: The study investigates the impact of technological process on the final properties of lead-free BFN ceramic materials. Results show that longer MA duration times can increase the perovskite phase content, while 40 hours of milling significantly improves the microstructure of BFN ceramics. The BFN(x)MA materials exhibit high electric permittivity values for energy storage applications and negative dielectric properties for shield elements against electromagnetic radiation.

MATERIALS (2021)

Add to Collection

Article Materials Science, Ceramics

DC electric field-assisted hot pressing of zirconia: Methodology, phenomenology, and sintering mechanism

Jingkun Xu et al.

Summary: This study successfully developed the electric field-assisted hot pressing (FAHP) technique to achieve flash sintering, effectively reducing grain sizes, and proposed a method to measure the current density limit for complete densification of 3YSZ.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2021)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Investigate the effect of process parameters of magnetic inductively assisted spark plasma sintering (SPS) of iron oxide (Fe3O4) on microstructure behaviour - Part I

Haetham G. Mohammed et al.

Summary: The new magnetically assisted spark plasma sintering technique introduces a continuous intensive magnetic field during the sintering process, improving material properties and reducing porosities. External magnetic fields parallel to the sintering process shorten processing times and refine grain structures, resulting in enhanced magnetic, electrical, and mechanical properties. The characterization of Fe3O4 nanopowder using various techniques confirms its suitability for the sintering process.

MATERIALS TODAY-PROCEEDINGS (2021)

Add to Collection

Article Materials Science, Ceramics

Direct coarse powder aqueous slip casting and pressureless sintering of highly transparent AlON ceramics

Xiannian Sun et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Materials Science, Ceramics

Gradient microstructure development and grain growth inhibition in high-entropy carbide ceramics prepared by reactive spark plasma sintering

Xiao-Feng Wei et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Spark Plasma Sintering as an Effective Texturing Tool for Reprocessing Recycled HDDR Nd-Fe-B Magnets with Lossless Coercivity

Awais Ikram et al.

METALS (2020)

Add to Collection

Article Materials Science, Ceramics

Effects of AlN content on mechanical and optical properties of AlON transparent ceramics

Hao Guo et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Review Materials Science, Multidisciplinary

A review of multi-physical fields induced phenomena and effects in spark plasma sintering: Fundamentals and applications

Zheng-Yang Hu et al.

MATERIALS & DESIGN (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of the AlON/Ti6Al4V active element brazing joint

Chun Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure Evolution of Fine-Grained Cobalt T400 Tribaloy Processed by Spark Plasma Sintering or Hot Isostatic Pressing of Gas-Atomized Powders

X. Boulnat et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)

Add to Collection

Article Materials Science, Ceramics

Effect of heating rate on properties of transparent aluminum oxynitride sintered by spark plasma sintering

Yingchun Shan et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2019)

Add to Collection

Article Materials Science, Ceramics

Formation of twins in AlON material and its effects on the Vickers hardness and fracture toughness

Maomao Ding et al.

CERAMICS INTERNATIONAL (2019)

Add to Collection

Article Materials Science, Ceramics

Fabrication of transparent γ-AlON by direct 2-step pressureless sintering of Al2O3 and AlN using an AlN-deficient composition

Ji-Hoon Min et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Static recrystallization of transparent polycrystalline yttrium aluminum garnet (YAG)

Wen Jiang et al.

SCRIPTA MATERIALIA (2019)

Add to Collection

Article Materials Science, Ceramics

Transparent AlON ceramic combined with VO2 thin film for infrared and terahertz smart window

Bo Peng et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Article Chemistry, Physical

Effects of pulse conditions on microstructure and mechanical properties of Si3N4/6061Al composites prepared by spark plasma sintering (SPS)

Han Jiang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Article Materials Science, Ceramics

Strengthening mechanism of twin lamellas in transparent AlON ceramics

Huilu Guo et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2018)

Add to Collection

Review Materials Science, Ceramics

Progress and Challenges in the Synthesis of AlON Ceramics by Spark Plasma Sintering

Xibao Li et al.

TRANSACTIONS OF THE INDIAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

SiC and ZrN nano-particulate reinforced AlON composites: Preparation, mechanical properties and toughening mechanisms

X. J. Zhao et al.

CERAMICS INTERNATIONAL (2016)

Add to Collection

Article Materials Science, Ceramics

Spark plasma sintering behavior of AlON ceramics doped with different concentrations of Y2O3

Xibao Li et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure evolution in HIPed AlON and its effect on optical property

Feng Chen et al.

OPTICAL MATERIALS EXPRESS (2015)

Add to Collection

Article Materials Science, Ceramics

The Effect of Grain Size on the Mechanical and Optical Properties of Spark Plasma Sintering-Processed Magnesium Aluminate Spinel MgAl2O4

Amnon Rothman et al.

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2014)

Add to Collection

Article Physics, Applied

Composition-dependent bonding and hardness of γ-aluminum oxynitride: A first-principles investigation

Bingtian Tu et al.

JOURNAL OF APPLIED PHYSICS (2014)

Add to Collection

Article Materials Science, Ceramics

First-Principles Insight into the Composition-Dependent Structure and Properties of γ-Alon

Bingtian Tu et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2014)

Add to Collection

Proceedings Paper Materials Science, Ceramics

Preparation of γ-AlON Transparent Ceramics by Pressureless Sintering

Feng Chen et al.

HIGH-PERFORMANCE CERAMICS VIII (2014)

Add to Collection

Article Materials Science, Ceramics

Preparation of AlON ceramics via reactive spark plasma sintering

Filiz Cinar Sahin et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2012)

Add to Collection

Article Materials Science, Multidisciplinary

Preparation and Light Transmission Properties of AlON Ceramics by the Two-Step Method with Nanosized Al2O3 and AlN

Jianqi Qi et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2011)

Add to Collection

Article Chemistry, Physical

Thermal conductivity of Spark Plasma Sintered AlN ceramics with multiple components sintering additive

Xiulan He et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2010)

Add to Collection

Article Materials Science, Ceramics

Ballistic testing of transparent armour ceramics

E. Strassburger

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2009)

Add to Collection

Article Materials Science, Ceramics

Fabrication and Microstructures of YAG Transparent Ceramics

M. Liu et al.

SCIENCE OF SINTERING (2008)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure and texture evolution in gel-cast α-alumina/alumina platelet ceramic composites

M Wei et al.

SCRIPTA MATERIALIA (2005)

Add to Collection

© Peeref 2019-2024. All rights reserved.