Related references
Note: Only part of the references are listed.Mechanical properties and microstructure of the Al0.3CoCrFeNiTi0.3 high entropy alloy under dynamic compression
Xianzhe Zhong et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)
Simultaneous enhancement of strength and ductility in a NiCoCrFe high-entropy alloy upon dynamic tension: Micromechanism and constitutive modeling
T. W. Zhang et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2020)
The effect of strain rate on mechanical properties and microstructure of a metastable FeMnCoCr high entropy alloy
Z. F. He et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
Ultra-high strain-rate strengthening in ductile refractory high entropy alloys upon dynamic loading
S. Zhang et al.
INTERMETALLICS (2020)
Simultaneous twinning and microband formation under dynamic compression in a high entropy alloy with a complex energetic landscape
D. L. Foley et al.
ACTA MATERIALIA (2020)
Dynamic Deformation Behaviors and Constitutive Relations of High-Strength Weldox700E Steel
Xianzhe Zhong et al.
ACTA MECHANICA SOLIDA SINICA (2019)
Effect of μ-precipitates on the microstructure and mechanical properties of non-equiatomic CoCrFeNiMo medium-entropy alloys
Jae Wung Bae et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2019)
Dynamic tensile deformation and microstructural evolution of AlxCrMnFeCoNi high-entropy alloys
C. M. Cao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Grain boundary decohesion by nanoclustering Ni and Cr separately in CrMnFeCoNi high-entropy alloys
Kaisheng Ming et al.
SCIENCE ADVANCES (2019)
Adiabatic shear localization in the CrMnFeCoNi high-entropy alloy
Zezhou Li et al.
ACTA MATERIALIA (2018)
Influence of deformation induced nanoscale twinning and FCC-HCP transformation on hardening and texture development in medium-entropy CrCoNi alloy
C. E. Slone et al.
ACTA MATERIALIA (2018)
Strain rate effects of dynamic compressive deformation on mechanical properties and microstructure of CoCrFeMnNi high-entropy alloy
Jeong Min Park et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Microstructural dependence of strain rate sensitivity in thermomechanically processed Al0.1CoCrFeNi high entropy alloy
Sindhura Gangireddy et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Magnetically-driven phase transformation strengthening in high entropy alloys
Changning Niu et al.
NATURE COMMUNICATIONS (2018)
Grain size dependence of strain rate sensitivity in a single phase FCC high entropy alloy Al0.3CoCrFeNi
Sindhura Gangireddy et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Serration behavior and negative strain rate sensitivity of Al0.1CoCrFeNi high entropy alloy
Mageshwari Komarasamy et al.
INTERMETALLICS (2017)
Negative to positive transition of strain rate sensitivity in Fe-22Mn-0.6C-x(Al) twinning-induced plasticity steels
H. K. Yang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Dynamic deformation behaviors and constitutive relations of an AlCoCr1.5Fe1.5NiTi0.5 high-entropy alloy
T. W. Zhang et al.
SCRIPTA MATERIALIA (2017)
Precipitation strengthening of ductile Cr15Fe20Co35Ni20Mo10 alloys
Kaisheng Ming et al.
SCRIPTA MATERIALIA (2017)
Effect of stacking faults on the ductility of Fe-18Mn-1.5Al-0.6C twinning-induced plasticity steel at low temperatures
Joon Yoo et al.
SCRIPTA MATERIALIA (2017)
Constitutive modeling of deformation behavior of high-entropy alloys with face-centered cubic crystal structure
Min Ji Jang et al.
MATERIALS RESEARCH LETTERS (2017)
Microstructure and mechanical properties of CoCrFeNiZrx eutectic high-entropy alloys
Wenyi Huo et al.
MATERIALS & DESIGN (2017)
High-velocity deformation of Al0.3CoCrFeNi high-entropy alloy: Remarkable resistance to shear failure
Z. Li et al.
SCIENTIFIC REPORTS (2017)
Microstructure evolution and critical stress for twinning in the CrMnFeCoNi high-entropy alloy
G. Laplanche et al.
ACTA MATERIALIA (2016)
The effect of interstitial carbon on the mechanical properties and dislocation substructure evolution in Fe40.4Ni11.3Mn34.8Al7.5Cr6 high entropy alloys
Zhangwei Wang et al.
ACTA MATERIALIA (2016)
Thermal activation mechanisms and Labusch-type strengthening analysis for a family of high-entropy and equiatomic solid-solution alloys
Zhenggang Wu et al.
ACTA MATERIALIA (2016)
A precipitation-hardened high-entropy alloy with outstanding tensile properties
J. Y. He et al.
ACTA MATERIALIA (2016)
Ductile CoCrFeNiMox high entropy alloys strengthened by hard intermetallic phases
W. H. Liu et al.
ACTA MATERIALIA (2016)
Mechanical Properties and Microstructure of the CoCrFeMnNi High Entropy Alloy Under High Strain Rate Compression
Bingfeng Wang et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2016)
Synthesis and microstructural characterization of a novel multicomponent equiatomic ZrNbAlTiV high entropy alloy
B. Vishwanadh et al.
SCRIPTA MATERIALIA (2016)
Atomic-scale properties of Ni-based FCC ternary, and quaternary alloys
Artur Tamm et al.
ACTA MATERIALIA (2015)
Mechanical properties, microstructure and thermal stability of a nanocrystalline CoCrFeMnNi high-entropy alloy after severe plastic deformation
B. Schuh et al.
ACTA MATERIALIA (2015)
Tensile deformation of low density duplex Fe-Mn-Al-C steel
Fuqiang Yang et al.
MATERIALS & DESIGN (2015)
Work hardening behavior involving the substructural evolution of an austenite-ferrite Fe-Mn-Al-C steel
Leifeng Zhang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
High strain-rate compressive deformation behavior of the Al0.1CrFeCoNi high entropy alloy
N. Kumar et al.
MATERIALS & DESIGN (2015)
Microstructural Evolution in Fe-22Mn-0.4C Twinning-Induced Plasticity Steel During High Strain Rate Deformation
Yumi Ha et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2015)
Temperature dependence of the mechanical properties of equiatomic solid solution alloys with face-centered cubic crystal structures
Z. Wu et al.
ACTA MATERIALIA (2014)
Effect of aluminum on the microstructure and properties of two refractory high-entropy alloys
O. N. Senkov et al.
ACTA MATERIALIA (2014)
A refractory Hf25Nb25Ti25Zr25 high-entropy alloy with excellent structural stability and tensile properties
Y. D. Wu et al.
MATERIALS LETTERS (2014)
A fracture-resistant high-entropy alloy for cryogenic applications
Bernd Gludovatz et al.
SCIENCE (2014)
Effect of Nb addition on the structure and mechanical behaviors of CoCrCuFeNi high-entropy alloy coatings
J. B. Cheng et al.
SURFACE & COATINGS TECHNOLOGY (2014)
Constitutive modelling of plasticity of fcc metals under extremely high strain rates
C. Y. Gao et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2012)
Variable strain rate sensitivity in an aluminum alloy: Response and constitutive modeling
Akhtar S. Khan et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2012)
Alloy Design and Properties Optimization of High-Entropy Alloys
Y. Zhang et al.
JOM (2012)
Decomposition in multi-component AlCoCrCuFeNi high-entropy alloy
S. Singh et al.
ACTA MATERIALIA (2011)
Dislocation and twin substructure evolution during strain hardening of an Fe-22 wt.% Mn-0.6 wt.% C TWIP steel observed by electron channeling contrast imaging
I. Gutierrez-Urrutia et al.
ACTA MATERIALIA (2011)
Dynamic mechanical behaviour and dislocation substructure evolution of Inconel 718 over wide temperature range
Woei-Shyan Lee et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Tensile ductility of ultra-fine grained copper at high strain rate
Suo Tao et al.
MATERIALS SCIENCE AND ENGINEERING APPLICATIONS, PTS 1-3 (2011)
Dependence of tensile deformation behavior of TWIP steels on stacking fault energy, temperature and strain rate
S. Curtze et al.
ACTA MATERIALIA (2010)
Direct Electrodeposition of Cu-Ni-W Alloys for the Liners for Shaped Charges
Hanwei He et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2010)
Stacking fault energy and plastic deformation of fully austenitic high manganese steels: Effect of Al addition
Kyung-Tae Park et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
HIGH SPEED TENSILE TEST OF STEEL SHEETS FOR THE STRESS-STRAIN CURVE AT THE INTERMEDIATE STRAIN RATE
H. Huh et al.
INTERNATIONAL JOURNAL OF AUTOMOTIVE TECHNOLOGY (2009)
Dynamical behaviour and microstructural evolution of a nitrogen-alloyed austenitic stainless steel
S. Frechard et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Microband-induced plasticity in a high Mn-Al-C light steel
Je Doo Yoo et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Effect of grain and twin boundaries on the hardening mechanisms of twinning-induced plasticity steels
O. Bouaziz et al.
SCRIPTA MATERIALIA (2008)
Novel microstructure and properties of multicomponent CoCrCuFeNiTix alloys
X. F. Wang et al.
INTERMETALLICS (2007)
Flow stress of Nitronic-50 stainless steel over a wide range of strain rates and temperatures
Wei- Guo Guo et al.
MECHANICS OF MATERIALS (2006)
Effect of strain rate on stress-strain behavior of alloy 309 and 304L austenitic stainless steel
JA Lichtenfeld et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2006)
On the stress dependence of partial dislocation separation and deformation microstructure in austenitic stainless steels
TS Byun
ACTA MATERIALIA (2003)
The onset of twinning in metals:: A constitutive description
MA Meyers et al.
ACTA MATERIALIA (2001)
The influence of stacking fault energy on the mechanical behavior of Cu and Cu-Al alloys: Deformation twinning, work hardening, and dynamic recovery
A Rohatgi et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2001)
Share Paper
