Related references
Note: Only part of the references are listed.Response of gyroid lattice structures to impact loads
Henrique Ramos et al.
INTERNATIONAL JOURNAL OF IMPACT ENGINEERING (2022)
Static and dynamic crushing of polymeric lattices fabricated by fused deposition modelling and selective laser sintering-an experimental investigation
Z. P. Sun et al.
INTERNATIONAL JOURNAL OF IMPACT ENGINEERING (2022)
Two elastically equivalent compound truss lattice materials with controllable anisotropic mechanical properties
Shuheng Wang et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2022)
Compressive performance and energy absorption of additively manufactured metallic hybrid lattice structures
Lijun Xiao et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2022)
Elastic properties of an additive manufactured three-dimensional vertex-based hierarchical re-entrant structure
Lumin Shen et al.
MATERIALS & DESIGN (2022)
Mechanical behavior and deformation mechanism of triply periodic minimal surface sheet under compressive loading
Zhonggang Wang et al.
MECHANICS OF ADVANCED MATERIALS AND STRUCTURES (2021)
Compression behavior of strut-reinforced hierarchical lattice-Experiment and simulation
Zhonggang Wang et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2021)
Quasi-static and dynamic compressive behaviour of sheet TPMS cellular structures
Nejc Novak et al.
COMPOSITE STRUCTURES (2021)
A topology strategy to reduce stress shielding of additively manufactured porous metallic biomaterials
Lei Zhang et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2021)
Strong and Tough Bioinspired Additive-Manufactured Dual-Phase Mechanical Metamaterial Composites
Sha Yin et al.
JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2021)
Process-induced geometric defect sensitivity of Ti-6Al-4V lattice structures with different mesoscopic topologies fabricated by electron beam melting
Lijun Xiao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
Deformation mechanisms and post-yielding behavior of additively manufactured lattice structures
Behzad Bahrami Babamiri et al.
MATERIALS & DESIGN (2020)
Plate-nanolattices at the theoretical limit of stiffness and strength
Cameron Crook et al.
NATURE COMMUNICATIONS (2020)
Critical instability at moving keyhole tip generates porosity in laser melting
Cang Zhao et al.
SCIENCE (2020)
Additive manufacturing of ultrafine-grained austenitic stainless steel matrix composite via vanadium carbide reinforcement addition and selective laser melting: Formation mechanism and strengthening effect
Bo Li et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Theoretical and numerical analysis of the mechanical responses of BCC and FCC lattice structures
Kyung-Won Lee et al.
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2019)
Mechanical properties of lightweight 316L stainless steel lattice structures fabricated by selective laser melting
Tianlin Zhong et al.
MATERIALS & DESIGN (2019)
A novel category of 3D chiral material with negative Poisson's ratio
Minghui Fu et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2018)
Mechanical properties of an improved 3D-printed rhombic dodecahedron stainless steel lattice structure of variable cross section
Xiaofei Cao et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2018)
Elastically-isotropic truss lattice materials of reduced plastic anisotropy
Thomas Tancogne-Dejean et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2018)
Compression behavior of lattice structures produced by selective laser melting: X-ray tomography based experimental and finite element up approaches
Yasin Amani et al.
ACTA MATERIALIA (2018)
Mechanical behaviour of auxetic cellular structures built from inverted tetrapods at high strain rates
Nejc Novak et al.
INTERNATIONAL JOURNAL OF IMPACT ENGINEERING (2018)
Elastically-isotropic elementary cubic lattices composed of tailored hollow beams
Thomas Tancogne-Dejean et al.
EXTREME MECHANICS LETTERS (2018)
Mechanical properties of open-cell rhombic dodecahedron titanium alloy lattice structure manufactured using electron beam melting under dynamic loading
Lijun Xiao et al.
INTERNATIONAL JOURNAL OF IMPACT ENGINEERING (2017)
Large deformation response of additively-manufactured FCC metamaterials: From octet truss lattices towards continuous shell mesostructures
Colin Bonatti et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2017)
Elastic and failure response of imperfect three-dimensional metallic lattices: the role of geometric defects induced by Selective Laser Melting
Lu Liu et al.
JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2017)
Additively-manufactured metallic micro-lattice materials for high specific energy absorption under static and dynamic loading
Thomas Tancogne-Dejean et al.
ACTA MATERIALIA (2016)
Multiscale metallic metamaterials
Xiaoyu Zheng et al.
NATURE MATERIALS (2016)
Mechanical behavior of open-cell rhombic dodecahedron Ti-6Al-4V lattice structure
Lijun Xiao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
Dynamic stress-strain states for metal foams using a 3D cellular model
Zhijun Zheng et al.
JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2014)
Finite element modelling of the compressive response of lattice structures manufactured using the selective laser melting technique
M. Smith et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2013)
Compressive behaviour of stainless steel micro-lattice structures
R. Gumruk et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2013)
Static mechanical behaviours of stainless steel micro-lattice structures under different loading conditions
Recep Gumruk et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Ultralight Metallic Microlattices
T. A. Schaedler et al.
SCIENCE (2011)
The quasi-static and blast loading response of lattice structures
S. McKown et al.
INTERNATIONAL JOURNAL OF IMPACT ENGINEERING (2008)
On the strength enhancement under impact loading of square tubes made from rate insensitive metals
H Zhao et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2004)
Effective properties of the octet-truss lattice material
VS Deshpande et al.
JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2001)
Foam topology bending versus stretching dominated architectures
VS Deshpande et al.
ACTA MATERIALIA (2001)
High strain rate compressive behaviour of aluminium alloy foams
VS Deshpande et al.
INTERNATIONAL JOURNAL OF IMPACT ENGINEERING (2000)