☆ 4.7 Article

Influence of the rolling of contact pads on crack initiation in fretting fatigue tests

INTERNATIONAL JOURNAL OF FATIGUE (2022)

Related references

Note: Only part of the references are listed.

Article Engineering, Mechanical

Modeling contact size effect on fretting wear: a combined contact oxygenation - third body approach

Soha Baydoun et al.

Summary: The study found that the wear rate decreases asymptotically with contact size, due to easier oxygen access to the interface favoring abrasive wear (COC) and faster ejection of protective debris particles (TBT). Wear rate evolutions and analyses suggest that COC is mainly driven by minimum distance between contact center and air contact edges, while TBT is mainly controlled by ratio of collinear contact length to sliding amplitude.

WEAR (2022)

Add to Collection

Article Engineering, Mechanical

Prediction of initiation and total life in fretting fatigue considering kinked cracks

Danilo Rangel et al.

Summary: This paper proposes a method to calculate fretting fatigue crack initiation and total life using iterative models calibrated with fatigue stress-strain-life curves, taking into account multiaxial non-proportional stress fields in fretting problems and stress gradient effects. The crack initiation path is obtained through the SWT parameter, and the analyzed results are validated by comparison with tests for an Aluminium 7075-T651 alloy in a cylindrical-flat configuration.

THEORETICAL AND APPLIED FRACTURE MECHANICS (2022)

Add to Collection

Article Engineering, Mechanical

Investigation on fretting fatigue crack initiation in heterogenous materials using a hybrid of multiscale homogenization and direct numerical simulation

Can Wang et al.

Summary: This paper investigates the fretting fatigue behavior of mechanically fastened joints considering the heterogeneity of materials. The authors propose a combination of Multiscale Homogenization and Direct Numerical Simulation (MH-DNS) method to improve the prediction accuracy of fretting fatigue life. Different models are used to compare the results, and the MH-DNS model shows the best-predicted results.

TRIBOLOGY INTERNATIONAL (2022)

Add to Collection

Article Engineering, Mechanical

Early crack orientation prediction methods under fretting fatigue loading including wear effects

A. L. Pinto et al.

Summary: This paper investigates two different methods for predicting crack initiation direction in fretting problems subjected to partial slip conditions. Experimental data from fretting tests on an AA7050-T7451 alloy were used for validation. The results show that the Critical Direction Method (CDM) provides accurate estimates, while the Linear Elastic Fracture Mechanics (LEFM) approach fails to reproduce the experimental observations. Additionally, it was found that considering wear has little effect on the estimates regardless of the method used.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

Add to Collection

Article Engineering, Mechanical

Effects of fretting wear process on fatigue crack propagation and life assessment

A. L. Pinto et al.

Summary: This paper proposes a new methodology for fretting fatigue life assessment, combining multiaxial fatigue criteria, theory of critical distances, and a node-displacement wear algorithm. Validation using available data showed a total life estimation error between 11% and -39%, emphasizing the importance of including wear in the modeling for accurate results.

TRIBOLOGY INTERNATIONAL (2021)

Add to Collection

Article Engineering, Mechanical

Effect of shot peening residual stresses and surface roughness on fretting fatigue strength of Al 7075-T651

Vicente Martin et al.

TRIBOLOGY INTERNATIONAL (2020)

Add to Collection

Article Engineering, Mechanical

Numerical analysis of toroidal voids as stress relievers in shrink-fitted shafts

D. Erena et al.

TRIBOLOGY INTERNATIONAL (2020)

Add to Collection

Article Engineering, Mechanical

Fretting fatigue and shot peening: a multiaxial fatigue criterion including residual stress relaxation

Sabrina Vantadori et al.

TRIBOLOGY INTERNATIONAL (2020)

Add to Collection

Article Engineering, Mechanical

Fretting fatigue of 7050-T7451 Al alloy: the influence of bulk mean stress

Sabrina Vantadori et al.

INTERNATIONAL JOURNAL OF FATIGUE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Fretting-Fatigue Analysis of Shot-Peened Al 7075-T651 Test Specimens

Vicente Martin et al.

METALS (2019)

Add to Collection

Article Engineering, Mechanical

Lifetime estimation of mechanical assemblies under constant amplitude fretting fatigue loading

Andrea Carpinteri et al.

FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2019)

Add to Collection

Article Engineering, Mechanical

Voids as stress relievers and a palliative in fretting

D. Erena et al.

FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2018)

Add to Collection

Article Engineering, Mechanical

Nucleation and early crack path in fretting fatigue

C. Navarro et al.

INTERNATIONAL JOURNAL OF FATIGUE (2017)

Add to Collection

Article Engineering, Mechanical

Investigations on the fretting fatigue failure mechanism of bolted joints in high strength steel subjected to different levels of pre-tension

Carlos Jimenez-Pena et al.

TRIBOLOGY INTERNATIONAL (2017)

Add to Collection

Article Engineering, Mechanical

Two dimensional versus three dimensional modelling in fretting fatigue life prediction

Jesus Vazquez et al.

JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN (2016)

Add to Collection

Review Materials Science, Multidisciplinary

Controlling the ignition and flammability of magnesium for aerospace applications

Frank Czerwinski

CORROSION SCIENCE (2014)

Add to Collection

Article Engineering, Mechanical

Explicit equations for sub-surface stress field in plane contacts

J. Vazquez et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2013)

Add to Collection

Article Engineering, Mechanical

Experimental results in fretting fatigue with shot and laser peened Al 7075-T651 specimens

J. Vazquez et al.

INTERNATIONAL JOURNAL OF FATIGUE (2012)

Add to Collection

Article Mechanics

A new method for obtaining the stress field in plane contacts

J. Vazquez et al.

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2012)

Add to Collection

Article Engineering, Mechanical

Determination of fatigue related discontinuity state of 7000 series of aerospace aluminum alloys

Ali Merati et al.

ENGINEERING FAILURE ANALYSIS (2007)

Add to Collection

Article Engineering, Mechanical

Fretting fatigue in a spherical contact

C Navarro et al.

JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN (2002)

Add to Collection

© Peeref 2019-2024. All rights reserved.