☆ 4.5 Article

Heterogeneous material joining of sapphire and TC4 alloy with a functionally graded interface

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Ceramics

Metallization of Al2O3 ceramic with Mg by friction stir spot welding

Hirosuke Sonomura et al.

Summary: The surfaces of Al2O3 ceramic plates were metallized using a friction stir spot welding method, showing good adhesive strength. Investigation revealed the formation of a microcrystalline MgO layer at the interface, leading to strong adhesion. Bonding two metallized Al2O3 ceramic plates together at 1100 °C under vacuum resulted in a strong cross tensile strength, indicating strong adhesion.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of welding heat input on microstructure and properties of TC4 titanium alloy ultra-narrow gap welded joint by laser welding with filler wire

Naiwen Fang et al.

Summary: The increase of laser welding heat input leads to an increase in the average grain size and width of the equiaxed crystal zone in the center of the weld, as well as a gradual tendency of grain angles in the columnar crystal zone to be perpendicular. The heat-affected zone widens without obvious grain coarsening. The microhardness value of the HAZ in the welded joint is lower than that of the weld and the base metal, while the tensile strength is slightly higher but the elongation after fracture is reduced with the increase of welding heat input.

MATERIALS RESEARCH EXPRESS (2021)

Add to Collection

Article Engineering, Industrial

Interfacial metal/ceramic bonding mechanism for metallization of ceramics via cold spraying

Jiahao Qin et al.

Summary: This study investigates the bonding mechanisms between metallic particles and ceramic substrates using aluminum particles and alumina substrates in cold spraying process. The results show that the aluminum coatings successfully bonded on the ceramic surfaces due to mechanical interlocking and heteroepitaxy, providing more details about the bonding processes.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection

Article Engineering, Industrial

Bonding and strengthening mechanism on ultrasonic-assisted soldering of sapphire using Sn-3.5Ag-4Al solder

Yan Xu et al.

Summary: The study demonstrated the successful joining of sapphire with a Sn-3.5Ag-4Al solder using fast ultrasonic-assisted soldering technique. The enhancement of shear strength in the joints was attributed to the formation of a transition layer of amorphous Al2O3 at the interface, along with the presence of Al enrichment layer and Ag3Al2 phases. These structures contributed to the strong interfacial bonding, ultimately improving the mechanical properties of the joints.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Ceramics

Fabrication and characterisation of high-performance joints made of ZrB2-SiC ultra-high temperature ceramics

Xiaochao Jin et al.

Summary: In this study, ZrB2-SiC composite UHTCs parts were successfully joined using Ni foil as filler, forming the ZrB2-SiC/Ni/ZrB2-SiC (ZS/Ni/ZS) joint with good mechanical properties and oxidation resistance. The joint had a shear strength of approximately 161 MPa, demonstrating satisfactory performance. Additionally, the joint showed good oxidation resistance for a wide range of elevated temperatures (800-1600 degrees C), making it suitable for extreme environments.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Ceramics

Mechanism of the interfacial reaction between sapphire and Sn-3.5Ag-4Ti solder at a low temperature in air by ultrasound

Yan Xu et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Engineering, Industrial

Diffusion welding of powder metallurgy high speed steel by spark plasma sintering

Weijun Shen et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Ceramics

Selective laser induced autocatalytic metallization of NiO and Cr2O3 doped alumina zirconia ceramic substrates

Philipp Ninz et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Aluminium self-diffusion in high-purity α-Al2O3: Comparison of Ti-doped and undoped single crystals

Peter Fielitz et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Materials Science, Ceramics

Brazing of SiC ceramics pretreated by chromium coating using inactive AgCu filler metal

Zubin Chen et al.

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

The effects of sintering temperature on mechanical and electrical properties of Al2O3/Ti composites

Shengfang Shi et al.

MATERIALS TODAY COMMUNICATIONS (2020)

Add to Collection

Article Materials Science, Ceramics

The fabrication of Al2O3-Al FGM by SPS under different sintering temperatures: Microstructural evaluation and bending behavior

Saeed Farahmand et al.

CERAMICS INTERNATIONAL (2019)

Add to Collection

Article Chemistry, Physical

Fracture toughness distribution of alumina-titanium functionally graded materials fabricated by spark plasma sintering

Tomoyuki Fujii et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural and XRD Analysis and Study of the Properties of the System Ti-TiAl-B4C Processed under Different Operational Conditions

Isabel Montealegre-Melendez et al.

METALS (2018)

Add to Collection

Article Engineering, Biomedical

Al2O3-Ti functionally graded material prepared by spark plasma sintering for orthopaedic applications

Marjan Bahraminasab et al.

JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Fabrication of a PSZ-Ti functionally graded material by spark plasma sintering and its fracture toughness

Tomoyuki Fujii et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Wetting and Brazing of Alumina by Sn0.3Ag0.7Cu-Ti Alloy

J. R. Kang et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Sputtered Hf-Ti nanostructures: A segregation and high-temperature stability study

Mikhail N. Polyakov et al.

ACTA MATERIALIA (2016)

Add to Collection

Article Chemistry, Physical

Crystallization, high temperature deformation behavior and solid-to-solid formability of a Ti-based bulk metallic glass within supercooled liquid region

Kwang Seok Lee et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural evolution and characterisation of interfacial phases in Al2O3/Ag-Cu-Ti/Al2O3 braze joints

Majed Ali et al.

ACTA MATERIALIA (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Vacuum brazing of sapphire with Inconel 600 using Cu/Ni porous composite interlayer for gas pressure sensor application

Tuan Zaharinie et al.

MATERIALS & DESIGN (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Temperature-gradient joining of Ti-6Al-4V alloys by pulsed electric current sintering

Daihua He et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)

Add to Collection

Article Materials Science, Ceramics

Brazing of Al2O3 to Ti-6Al-4V alloy with in situ synthesized TiB-whisker-reinforced active brazing alloy

Minxuan Yang et al.

CERAMICS INTERNATIONAL (2011)

Add to Collection

Article Materials Science, Multidisciplinary

Synthesis of TiB2-TiC-Ni/TiAl/Ti functionally gradient materials by FAPAS process

Liang Lianjie et al.

RARE METALS (2011)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure and fracture behavior of SiO2 glass ceramic and TC4 alloy joint brazed with TiZrNiCu alloy

Liu Duo et al.

JOURNAL OF CENTRAL SOUTH UNIVERSITY OF TECHNOLOGY (2009)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure of alumina cerarnic/Ag-Cu-Ti brazing alloy/Kovar alloy joint

Y. Wang et al.

MATERIALS SCIENCE AND TECHNOLOGY (2007)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and mechanical performance of brazed joints of Cf/SiC composite and Ti alloy using Ag-Cu-Ti-W

G. B. Lin et al.

SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2006)

Add to Collection

© Peeref 2019-2024. All rights reserved.