Related references
Note: Only part of the references are listed.Recovery of carbon fiber from prepreg using nitric acid and evaluation of recycled CFRP
Takuma Hanaoka et al.
COMPOSITES PART B-ENGINEERING (2022)
A Systematic Characterization Approach for Vacuum Bag Only Prepregs towards an Accurate Process Design
Muhammed H. Arikan et al.
MATERIALS (2022)
A Low-Cost Filament Winding Technology for University Laboratories and Startups
Artem Andrianov et al.
POLYMERS (2022)
Amino-functionalized carbon nanotubes for effectively improving the mechanical properties of pre-impregnated epoxy resin/carbon fiber
Alan Silva dos Santos et al.
JOURNAL OF APPLIED POLYMER SCIENCE (2021)
Continuous processing of pre-pregs using radio frequency heating
Aniruddh Vashisth et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2020)
A novel powder-epoxy towpregging line for wind and tidal turbine blades
Colin Robert et al.
COMPOSITES PART B-ENGINEERING (2020)
Dynamic Capillary-Driven Additive Manufacturing of Continuous Carbon Fiber Composite
Baohui Shi et al.
MATTER (2020)
Development of vacuum-assisted prepreg compression molding for production of automotive roof panels
Jeong-Min Lee et al.
COMPOSITE STRUCTURES (2019)
Characterization of fibre alignment in as-received aerospace grade unidirectional prepreg
Andrew L. Stewart et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2018)
Understanding and predicting defect formation in automated fibre placement pre-preg laminates
Jonathan P. -H. Belnoue et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2017)
Fast-curing epoxy polymers with silica nanoparticles: properties and rheo-kinetic modelling
A. Keller et al.
JOURNAL OF MATERIALS SCIENCE (2016)
Influence of cure kinetic, rheological and thermo-mechanical behavior on micro-level curing strain of an epoxy prepreg
A. S. Ganapathi et al.
JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2016)
An analytical model for B-stage joining and co-curing of carbon fibre epoxy composites
J. Studer et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2016)
A review of out-of-autoclave prepregs - Material properties, process phenomena, and manufacturing considerations
T. Centea et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2015)
Design and verification of a single slab RAS through mass production of glass/MWNT added epoxy composite prepreg
Jae-Hwan Shin et al.
JOURNAL OF APPLIED POLYMER SCIENCE (2015)
Combination of carbon fibre sheet moulding compound and prepreg compression moulding in aerospace industry
Jens Wulfsberg et al.
11TH INTERNATIONAL CONFERENCE ON TECHNOLOGY OF PLASTICITY, ICTP 2014 (2014)
Resin film impregnation in fabric prepregs with dual length scale permeability
Thomas A. Cender et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2013)
The engineering aspects of automated prepreg layup: History, present and future
Dirk H. -J. A. Lukaszewicz et al.
COMPOSITES PART B-ENGINEERING (2012)
Development of the properties of a carbon fibre reinforced thermosetting composite through cure
Nuri Ersoy et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2010)
Thermal Curing of Glass-Epoxy Prepregs by Luminescence Spectroscopy
R. C. M. Sales et al.
JOURNAL OF APPLIED POLYMER SCIENCE (2010)
Life cycle energy analysis of fiber-reinforced composites
Young S. Song et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2009)
Study on the curing process and the gelation of epoxy/anhydride system for no-flow underfill for flip-chip applications
ZQ Zhang et al.
MACROMOLECULAR MATERIALS AND ENGINEERING (2003)
Share Paper
