☆ 4.7 Article

Understanding tack behaviour during prepreg-based composites' processing

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2023)

Related references

Note: Only part of the references are listed.

Article Engineering, Aerospace

Influence and optimization of parameters of prepreg viscosity during placement

Lei ZU et al.

Summary: This paper tested and studied the viscosity of prepreg in the automatic placement process. The results showed the relationship between viscosity and laying rate, laying pressure, and laying temperature. Peel tests were simulated to validate the correctness of the test data and the two-line cohesion model. The laying process parameters were optimized using a response surface test.

CHINESE JOURNAL OF AERONAUTICS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Quantifying the Influence of Out-Time on Prepreg Material Properties and Out-Of-Plane Steering Defects During Automated Fiber Placement

Klaus Heller et al.

Summary: In automated fiber placement (AFP), understanding the interaction between material properties and process parameters is crucial for cost-efficient manufacturing. This study quantifies the changes in mechanical properties and tack of uncured prepreg tapes over time, and investigates their impact on the occurrence of defects during AFP lay-up trials.

FRONTIERS IN MATERIALS (2022)

Add to Collection

Article Engineering, Civil

Process-dependent wrinkle formation for steered tow during automated fiber placement: Modeling and experimental verification

Helin Pan et al.

Summary: This paper conducts an experimental study to explore the interaction between process parameters and wrinkle formation during tow steering in automated fiber placement (AFP). A process-dependent theoretical model is proposed, and closed-form solutions for predicting critical steering radius and stress distribution coefficient are derived. The model is validated by steering trials and shows good agreement with experimental results. The influence of process parameters on critical steering radius is discussed, and it is demonstrated that adjusting process parameters based on the proposed model can improve lay-up efficiency and quality.

THIN-WALLED STRUCTURES (2022)

Add to Collection

Article Engineering, Chemical

Analysis of contact area in a continuous application-and-peel test method for prepreg tack

G. Y. H. Choong et al.

Summary: The relationship between prepreg tack and the degree of intimate contact (DoIC) between prepreg and a rigid substrate was explored through continuous application-and-peel test method. It was found that optimal feed rates and compaction pressure could increase tack and contact area. As feed rates decrease, both true contact area and tack increase, but at a critical rate, the bond failure mechanism switches from adhesive to cohesive failure.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2021)

Add to Collection

Article Materials Science, Composites

Wrinkle Formation and Initial Defect Sensitivity of Steered Tow in Automated Fiber Placement

Meisam Kheradpisheh et al.

Summary: This paper investigates the wrinkle formation of a prepreg with initial defect during steering in automated fiber placement (AFP) and its impact on mechanical properties. A theoretical model and numerical methods are developed to solve the wrinkle problem, validated by experimental results to accurately predict wrinkle formation wavelengths.

JOURNAL OF COMPOSITES SCIENCE (2021)

Add to Collection

Article Engineering, Manufacturing

Hypo-viscoelastic modelling of in-plane shear in UD thermoset prepregs

Yi Wang et al.

Summary: Recent studies have found that in-plane shear behavior of prepreg material during manufacturing is influenced by deformation rate and temperature. A phenomenological viscoelastic model has been formulated to better understand this behavior.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2021)

Add to Collection

Article Materials Science, Composites

Adhesion-cohesion balance of prepreg tack in thermoset automated fiber placement. Part 1: Adhesion and surface wetting

D. Budelmann et al.

Summary: The constitution of prepreg tack in automated fiber placement is influenced by factors such as surface roughness, surface energy, and viscous resin flow. Contact angle measurements showed a correlation between thermodynamic work of adhesion and maximum tack, indicating the importance of molecular interaction at the interface between prepreg resin and substrate. Matching ratios of polar and dispersive surface free energy components were found to enhance adhesion between the materials.

COMPOSITES PART C: OPEN ACCESS (2021)

Add to Collection

Article Engineering, Manufacturing

Adaptation of material deposition parameters to account for out-time effects on prepreg tack

A. W. Smith et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2020)

Add to Collection

Review Materials Science, Composites

Prepreg tack: A review of mechanisms, measurement, and manufacturing implication

Dennis Budelmann et al.

POLYMER COMPOSITES (2020)

Add to Collection

Article Engineering, Manufacturing

Experimental characterisation of the in-plane shear behaviour of UD thermoset prepregs under processing conditions

Yi Wang et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2020)

Add to Collection

Article Engineering, Multidisciplinary

Simulations and experiments for automated fiber placement of prepreg slit tape: Wrinkle formation and fundamental observations

Sreehari Rajan et al.

COMPOSITES PART B-ENGINEERING (2020)

Add to Collection

Article Engineering, Multidisciplinary

Numerical modeling of interply adhesion in composite forming of viscous discontinuous thermoplastic prepregs

P. D. Mulye et al.

COMPOSITES PART B-ENGINEERING (2020)

Add to Collection

Article Engineering, Multidisciplinary

Modelling defect formation in textiles during the double diaphragm forming process

Adam J. Thompson et al.

COMPOSITES PART B-ENGINEERING (2020)

Add to Collection

Article Engineering, Manufacturing

Interaction of process parameters and material properties with regard to prepreg tack in automated lay-up and draping processes

D. Budelmann et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2019)

Add to Collection

Article Engineering, Manufacturing

Nonlinear hyperviscoelastic modelling of intra-ply deformation behaviour in finite element forming simulation of continuously fibre-reinforced thermoplastics

Dominik Doerr et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2018)

Add to Collection

Article Materials Science, Composites

Wrinkle formation during steering in automated fiber placement: Modeling and experimental verification

Muhsan Belhaj et al.

JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2018)

Add to Collection

Article Engineering, Manufacturing

An experimental and simulative study on the defects appeared during tow steering in automated fiber placement

Nima Bakhshi et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2018)

Add to Collection

Article Engineering, Manufacturing

Characterisation of tack for uni-directional prepreg tape employing a continuous application-and-peel test method

Andreas Endruweit et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2018)

Add to Collection

Article Engineering, Manufacturing

Understanding the buckling behaviour of steered tows in Automated Dry Fibre Placement (ADFP)

M. Y. Matveev et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2016)

Add to Collection

Article Engineering, Chemical

Modelling adhesive joints with cohesive zone models: effect of the cohesive law shape of the adhesive layer

R. D. S. G. Campilho et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2013)

Add to Collection

Article Engineering, Manufacturing

The experimental determination of prepreg tack and dynamic stiffness

R. J. Crossley et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2012)

Add to Collection

Article Engineering, Multidisciplinary

The engineering aspects of automated prepreg layup: History, present and future

Dirk H. -J. A. Lukaszewicz et al.

COMPOSITES PART B-ENGINEERING (2012)

Add to Collection

Article Mechanics

Intra/inter-ply shear behaviors of continuous fiber reinforced thermoplastic composites in thermoforming processes

Qianqian Chen et al.

COMPOSITE STRUCTURES (2011)

Add to Collection

Article Mechanics

Modelling slit tape buckling during automated prepreg manufacturing: A local approach

A. Beakou et al.

COMPOSITE STRUCTURES (2011)

Add to Collection

Article Materials Science, Multidisciplinary

Experimental Analysis of Prepreg Tack

O. Dubois et al.

EXPERIMENTAL MECHANICS (2010)

Add to Collection

Article Mechanics

Development of a new structural prepreg: characterisation of handling, drape and tack properties

R Banks et al.

COMPOSITE STRUCTURES (2004)

Add to Collection

© Peeref 2019-2024. All rights reserved.