☆ 4.5 Article

Built-up edge formation mechanisms in orthogonal cutting of wood-plastic composite

WOOD MATERIAL SCIENCE & ENGINEERING (2022)

Related references

Note: Only part of the references are listed.

Article Chemistry, Physical

Machinability of Different Wood-Plastic Composites during Peripheral Milling

Zhaolong Zhu et al.

Summary: The aim of this study was to improve the machinability of wood-plastic composites by investigating the effects of different wood-plastic composites on machinability. The effects of milling with cemented carbide cutters were examined, and cutting forces, cutting temperature, surface quality, chip formation, and tool wear were evaluated. Optimal milling conditions were determined, and different wear patterns and chip formations were observed during the machining process of different wood-plastic composites.

MATERIALS (2022)

Add to Collection

Article Engineering, Mechanical

Improving Precision in Aluminum Alloy Machining Due to the Application of Diamond-Like Carbon Thin Film

William de Melo Silva et al.

Summary: The study showed that built up edge (BUE) affects cutting precision during low speed cutting of aluminum alloy, but using diamond-like carbon (DLC) film can improve the tool performance.

JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2021)

Add to Collection

Article Forestry

Machinability of wood fiber/polyethylene composite during orthogonal cutting

Xiaolei Guo et al.

Summary: The study investigated the machinability of wood fiber/polyethylene composite material and found that the cutting depth affects the cutting efficiency and surface quality. Shallow cutting depth results in continuous cutting governed by a continuous shearing process, while deep cutting depth leads to discontinuous cutting governed by plastic fracture.

WOOD SCIENCE AND TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation of the Wear Behavior of PVD Coated Carbide Tools during Ti6Al4V Machining with Intensive Built Up Edge Formation

M. S. I. Chowdhury et al.

Summary: The study investigates the effect of AlTiN and CrN PVD coatings on tool wear during the machining of a Ti6Al4V alloy with severe BUE formation. It demonstrates that CrN coating possesses unique micromechanical properties and tribological adaptive characteristics, minimizing BUE formation and significantly improving tool performance.

COATINGS (2021)

Add to Collection

Article Forestry

Effects of laser parameters on the width of color change area of poplar wood surface during a single irradiation

Rongrong Li et al.

Summary: The laser surface treatment method is efficient for modifying wood properties like color, wettability, and surface roughness. By experimenting, it was found that laser power and focus plane position significantly influence the width of color change area (WCCA). A quadratic model was established to accurately predict WCCA under different laser parameter combinations.

EUROPEAN JOURNAL OF WOOD AND WOOD PRODUCTS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Evaluation and Modeling of Processability of Laser Removal Technique for Bamboo Outer Layer

Rongrong Li et al.

Summary: CO2 laser removal technique was used for bamboo outer layer removal, with laser power having the most significant impact on removal depth and surface morphology. Feed speed and sweep width had opposite effects compared to laser power on the assessed parameters.

JOM (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of Tool Wear on Form Deviations in Dry Machining of UNS A97075 Alloy

Francisco Javier Trujillo Vilches et al.

Summary: Geometrical tolerances play a crucial role in the functionality and assembly of parts made of light alloys for aeronautical applications, which are often machined in dry conditions where tool wear becomes a significant factor affecting geometrical tolerances. In this study, the impact of tool wear on roundness, straightness, and cylindricity of dry-turned UNS A97075 alloy was analyzed, with indirect adhesion wear being identified as the main tool-wear mechanism influenced by feed. The findings highlight a relationship between cutting parameters, cutting time, tool wear, and form deviations, particularly emphasizing the influence of high feed and low cutting speed values on tool wear.

METALS (2021)

Add to Collection

Article Engineering, Manufacturing

Processing of T6 heat-treated Al-12Si-0.6Mg alloy

Senol Bayraktar et al.

MATERIALS AND MANUFACTURING PROCESSES (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Zinc Content and Cutting Tool Coating on the Machinability of the Al-(5-35) Zn Alloys

Senol Bayraktar et al.

METALS AND MATERIALS INTERNATIONAL (2020)

Add to Collection

Article Engineering, Mechanical

Machinability properties of Al-7Si, Al-7Si-4Zn and Al-7Si-4Zn-3Cu alloys

Senol Bayraktar et al.

JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2020)

Add to Collection

Article Engineering, Mechanical

Effect of rake angle on cutting performance during machining of stone-plastic composite material with polycrystalline diamond cutters

Pingxiang Cao et al.

JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Cutting performance of cemented carbide cutting tool in turning high-density fiberboard

Z. Zhu et al.

MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK (2018)

Add to Collection

Article Engineering, Chemical

Surface modification and improved adhesion of wood-plastic composites (WPCs) made with different polymers by treatment with atmospheric pressure rotating plasma jet

Andres Jesus Yanez-Pacios et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2017)

Add to Collection

Article Automation & Control Systems

The effects of cutting parameters and tool geometry on cutting forces and tool wear in milling high-density fiberboard with ceramic cutting tools

Zhaolong Zhu et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)

Add to Collection

Article Materials Science, Composites

A study on cutting temperature for wood-plastic composite

Zhijian Pei et al.

JOURNAL OF THERMOPLASTIC COMPOSITE MATERIALS (2016)

Add to Collection

Article Forestry

Effect of tool material on tool wear and delamination during machining of particleboard

Krzysztof Szwajka et al.

JOURNAL OF WOOD SCIENCE (2016)

Add to Collection

Article Materials Science, Paper & Wood

Cutting Forces and Chip Morphology during Wood Plastic Composites Orthogonal Cutting

Xiaolei Guo et al.

BioResources (2014)

Add to Collection

Article Engineering, Industrial

Stability and high performance machining conditions in simultaneous milling

Erhan Budak et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2013)

Add to Collection

Article Automation & Control Systems

Study on the optimization of cutting parameters in turning thin-walled circular cylindrical shell based upon cutting stability

Dong Chen et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)

Add to Collection

Article Acoustics

Effects of built-up edge-induced oscillations on chip formation during turning

Zoltan Palmai et al.

JOURNAL OF SOUND AND VIBRATION (2013)

Add to Collection

Article Engineering, Mechanical

Analysis of the evolution of the Built-Up Edge and Built-Up Layer formation mechanisms in the dry turning of aeronautical aluminium alloys

A. Gomez-Parra et al.

WEAR (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Design, optimization and manufacturing of wood-plastic composite pallet

E. Soury et al.

MATERIALS & DESIGN (2009)

Add to Collection

Article Materials Science, Composites

Mechanical properties of wood plastic composite panels made from waste fiberboard and particleboard

Majid Chaharmahali et al.

POLYMER COMPOSITES (2008)

Add to Collection

Article Materials Science, Multidisciplinary

Chip and built-up edge formation in the machining of in situ Al4C3-Al composite

Y Ozcatalbas

MATERIALS & DESIGN (2003)

Add to Collection

Article Engineering, Industrial

Wear mechanismes of new tool materials for Ti-6Al-4V high performance machining

N Corduan et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2003)

Add to Collection

© Peeref 2019-2024. All rights reserved.