☆ 4.5 Article

Statistical analysis and ANN modelling of tribological performance of aluminium hybrid composites fabricated by PM method

SURFACE TOPOGRAPHY-METROLOGY AND PROPERTIES (2022)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Influence of compaction pressure and Si3N4/ZrO2 reinforcement on the properties of aluminium hybrid composites

Aasiya Parveen et al.

Summary: Aluminium hybrid composites (AHCs) were developed in this study using powder metallurgy method, with varying weight percentages of Si3N4 and ZrO2 reinforcements. The SEM results showed uniform distribution of reinforcement and matrix particles, with accumulation of nano-size ZrO2 particles. With increasing compaction pressure and weight percentages of reinforcements, density and micro-hardness improved while porosity decreased. The highest hardness value was found to be 72 VHN for sample E at 500 MPa.

ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES (2022)

Add to Collection

Article Engineering, Mechanical

Influence of ultrasonic agitation on the abrasive wear characteristics of Al-Cu/2 vol% Grp composite

Ramendra Kumar Gupta et al.

Summary: In this study, the abrasive wear behavior of an Al-4.4 wt% Cu composite reinforced with 2 vol% graphite particles was investigated. The composite was prepared through Ultrasonic Treatment (UT) to achieve a uniform distribution of reinforcement particles. Wear tests were conducted on composites with and without UT treatment, as well as on the base alloy. The results showed that the composite with UT treatment exhibited higher coefficient of friction and wear resistance at 5 and 10 Newton loads compared to the base alloy. However, at 15 and 20 N load, the composite had lower COF and wear resistance. Micro-plowing and micro-cutting were identified as the two wear mechanisms for both the base alloy and the composites.

SURFACE TOPOGRAPHY-METROLOGY AND PROPERTIES (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Optimization of wear behaviour of Al7075/SiC/Al2O3 MMCs Using statistical method

M. Ravikumar et al.

Summary: Metal matrix composites are widely used in engineering applications for their improved mechanical and wear properties. This research focuses on fabricating hybrid MMCs by incorporating different wt. % of ceramic reinforcements into Al-7075 alloy through liquid metallurgical technique. The hardness of the composites was measured and found to increase with the reinforcement content. Pin on disc wear tests under dry sliding conditions were conducted, and the influence of wear parameters on wear loss and coefficient of friction was studied using ANOVA technique. The results showed that the wt. % of reinforcement has a significant impact on wear and COF. SEM and EDS analysis were used to investigate the wear mechanism.

ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES (2022)

Add to Collection

Article Engineering, Mechanical

Mechanical and corrosion behavior of SiC/Graphite/ZrO2 hybrid reinforced aluminum-based composites for marine environment

Sukriti Yadav et al.

Summary: This study investigates the mechanical and corrosion behavior of aluminum-based composites reinforced with hybrid reinforcements in marine conditions. Results show that the 3% reinforcement composite has the optimum mechanical properties and minimum corrosion rate, with increased hardness and tensile strength compared to pure Al. The corrosion behavior of the composite in simulated seawater conditions revealed a pitting corrosion mechanism with the 3% reinforced composite having the least corrosion rate.

SURFACE TOPOGRAPHY-METROLOGY AND PROPERTIES (2021)

Add to Collection

Article Engineering, Multidisciplinary

Fabrication and analysis of two-wheeler connecting rod for aluminium hybrid composites using finite element method

Aasiya Parveen et al.

Summary: This study developed a composite material Al/3 wt% Si3N4/4.5 wt% ZrO2 using powder metallurgy process and designed a connecting rod for TVS Apache 150 motor engine specifications using Solidworks software. The finite element method analysis in ANSYS Workbench showed a significant reduction in von-Mises stress for the developed composite material compared to existing composite materials.

ENGINEERING RESEARCH EXPRESS (2021)

Add to Collection

Article Engineering, Multidisciplinary

Analysis and prediction of the tensile strength of aluminum alloy composite using statistical and artificial neural network technique

Mohammad Mohsin et al.

Summary: Aluminum alloy (Al-20Fe-5Cr) matrix-based aluminum oxide (Al2O3) reinforced composites were developed through powder metallurgy (P/M) process. The study analyzed the impact of compaction pressure and wt.% of Al2O3 on tensile strength and elongation. Results showed that tensile strength increased with the addition of Al2O3, while elongation decreased.

ENGINEERING RESEARCH EXPRESS (2021)

Add to Collection

Review Materials Science, Multidisciplinary

A comprehensive review on material selection, processing, characterization and applications of aluminium metal matrix composites

V. Mahesh Kumar et al.

MATERIALS RESEARCH EXPRESS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Rice husk ash reinforced aluminium matrix composites: fabrication, characterization, statistical analysis and artificial neural network modelling

Mohd Bilal Naim Shaikh et al.

MATERIALS RESEARCH EXPRESS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Analysis of tribological behaviour of zirconia reinforced Al-SiC hybrid composites using statistical and artificial neural network technique

Sajjad Arif et al.

MATERIALS RESEARCH EXPRESS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Wear rate optimization of Al/SiCnp/e-glass fibre hybrid metal matrix composites using Taguchi method and genetic algorithm and development of wear model using artificial neural networks

Arunkumar M. Bongale et al.

MATERIALS RESEARCH EXPRESS (2018)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Fabrication methods of particulate reinforced Aluminium metal matrix composite-A review

Narender Panwar et al.

MATERIALS TODAY-PROCEEDINGS (2018)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

A review on effect of powder metallurgy process on mechanical and tribological properties of Hybrid nano composites

Omkar M. Patil et al.

MATERIALS TODAY-PROCEEDINGS (2018)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Characteristic Behaviour of Aluminium Metal Matrix Composites: A Review

Manish Shukla et al.

MATERIALS TODAY-PROCEEDINGS (2018)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Latest Research Development in Aluminum Matrix with Particulate Reinforcement Composites - A Review

A. Thirumoorthy et al.

MATERIALS TODAY-PROCEEDINGS (2018)

Add to Collection

Article Engineering, Chemical

Fabrication of 6061 aluminum alloy reinforced with Si3N4/n-Gr and its wear performance optimization using integrated RSM-GA

Neeraj Sharma et al.

PARTICULATE SCIENCE AND TECHNOLOGY (2017)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Optimization of friction and wear behaviour of Al-Si3N4 nano composite and Al-Gr-Si3N4 hybrid composite under dry sliding conditions

R. Ambigai et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Study of mechanical and tribological behaviour of Al/SiC/ZrO2 hybrid composites fabricated through powder metallurgy technique

Sajjad Arif et al.

MATERIALS RESEARCH EXPRESS (2017)

Add to Collection

Article Engineering, Civil

An investigation of abrasive and erosion behaviour of AA 2618 reinforced with Si3N4, AlN and ZrB2 in situ composites by using optimization techniques

Senthil Kumaran Selvaraj et al.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2017)

Add to Collection

Article Engineering, Multidisciplinary

Wear behaviour of Al 2618 alloy reinforced with Si3N4, AlN and ZrB2 in situ composites at elevated temperatures

N. Mathan Kumar et al.

ALEXANDRIA ENGINEERING JOURNAL (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Parametric Study of Dry Sliding Wear Behavior of Hybrid Metal Matrix Composite Produced by a Novel Process

Pardeep Sharma et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2015)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Dry Sliding Wear Behavior of Powder Metallurgy Aluminium Matrix Composite

R. Ganesh et al.

MATERIALS TODAY-PROCEEDINGS (2015)

Add to Collection

Review Materials Science, Multidisciplinary

Properties of ceramic-reinforced aluminium matrix composites - a review

Dipti Kanta Das et al.

INTERNATIONAL JOURNAL OF MECHANICAL AND MATERIALS ENGINEERING (2014)

Add to Collection

Article Engineering, Mechanical

Friction and wear behavior of Ni-P coated Si3N4 reinforced Al6061 composites

C. S. Ramesh et al.

TRIBOLOGY INTERNATIONAL (2010)

Add to Collection

Article Engineering, Industrial

The production and application of metal matrix composite materials

JW Kaczmar et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.