☆ 4.7 Article

Investigation on characteristic and formation mechanism of porosity defects of Al-Li alloys prepared by sand casting

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Related references

Note: Only part of the references are listed.

Article Nanoscience & Nanotechnology

High solid-solution strengthening mechanism of a novel aluminum-lithium alloy fabricated by electromagnetic near-net shape technology

Shiju Li et al.

Summary: The microstructure evolution and precipitation strengthening behavior of Al-Li alloy manufactured by traditional casting, twin-roll casting (TRC) and electromagnetic twin-roll casting (E-TRC) were systematically investigated. The results show that the high cooling rate of the TRC process makes more alloying elements dissolve in the alpha(Al) matrix and improve the supersaturated solid solubility of the alloy. The electromagnetic oscillation field (EOF) in the TRC process enhances the mixing capability and diffusion ability of the solute atoms and inhibits the recrystallization of deformed microstructure, resulting in reduced macro-segregation and refined solidified microstructure. E-TRC increases the intragranular solid-solution capacity of the solute, leading to more and finer strengthening phases in the aging process, greatly improving the aging strengthening effect and significantly increasing the strength of the Al-Li alloy.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of the aging process and pre-deformation on the precipitated phase and mechanical properties of 2195 Al-Li alloy

Bingxin Xie et al.

Summary: Increasing aging temperature can improve aging kinetics and decrease the density of precipitated phases; double aging is beneficial for uniform size and distribution of precipitated phases; pre-deformation increases nucleation sites of T1 phase, reducing its average size.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Effects of wet shot peening on microstructures and mechanical properties of a 2060-T8 aluminum-lithium alloy

Xuefei Tao et al.

Summary: In this study, wet shot peening (WSP) was used to modify the microstructures and mechanical properties of an aluminum-lithium (Al-Li) alloy. Numerical simulation and experimental methods were employed to investigate the effects of WSP. The results showed that the gradient distributions of plastic strain and strain rate induced by WSP were the primary factors determining the microstructural evolution and deformation mechanisms. Experimental characterization revealed that WSP significantly improved the yield strength, tensile strength, and microhardness of the alloy, but reduced its total elongation. The non-uniform deformation of WSP also resulted in a gradient hierarchical microstructure that promoted the accumulation of geometrically necessary dislocations, leading to extra hardening effects.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Chemistry, Physical

Multicomponent Aging Al-Li-Based Alloys of the Latest Generation: Structural and Phase Transformations, Treatments, Properties, and Future Prospects

Dmitriy Y. Rasposienko et al.

Summary: This article provides an overview of modern material science problems in ultralightweight high-modulus commercial Al-Li-based alloys, highlighting successful innovations in the Soviet and Russian aviation industry. The key regularities of multicomponent alloying are discussed, along with the microstructures, phase composition, and properties formed during aging. The main mechanisms of phase formation are generalized, and recent achievements in designing unique structural and phase transformations through severe plastic deformations and heat treatment are presented.

MATERIALS (2022)

Add to Collection

Article Thermodynamics

Kinetic analysis of resin binder for casting in combustion decomposition process

Peng Wan et al.

Summary: This study used TG-DTA technology to analyze the combustion decomposition process of different resin binders, obtaining parameters such as residual mass and activation energy at high temperatures, providing important data support for thermal reclamation.

JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Internal Porosity Defects in Ductile Cast Irons

Yoshiaki Takemoto et al.

Summary: The formation of internal porosity defects in ductile cast irons may be related to the reductive reaction of carbon and FeO in solid bifilms, and can be prevented by avoiding the entrainment of carbon and oxide films.

INTERNATIONAL JOURNAL OF METALCASTING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Enhanced mechanical properties of 6082 aluminum alloy via SiC addition combined with squeeze casting

Wenming Jiang et al.

Summary: The addition of SiCp and squeeze casting have significant impacts on microstructure and mechanical properties of the 6082 aluminum alloy. The use of SiCp and squeeze casting can significantly improve the mechanical properties of the 6082 aluminum alloy, including increasing tensile strength, yield strength, elongation, elastic modulus and hardness.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Creep aging properties variation and microstructure evolution for 2195 Al-Li alloys with various loading rates

Fei Chen et al.

Summary: This study investigated the effects of different loading rates on creep aging treatment of Al-Li alloy, finding that the loading rate effectively influences the creep aging behavior of the materials. A higher loading rate is beneficial for the accumulation of creep strain and promotes the nucleation of T-1 phase, contributing to improved material properties.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Chemistry, Physical

Analysis of microstructure and high-temperature tensile properties of 2060 Al-Li alloy strengthened by laser shock peening

Xingwei Zheng et al.

Summary: The study demonstrates that laser shock peening can enhance the strength of 2060 alloy while reducing ductility, with dislocation strengthening identified as the primary mechanism for improving high-temperature tensile properties.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Chemistry, Physical

Effects of heat treatment on the microstructure, texture and mechanical property anisotropy of extruded 2196 Al-Cu-Li alloy

Xiaoxue Chen et al.

Summary: The mechanical properties and microstructures of extruded 2196 Al-Cu-Li alloy plates under different heat treatment parameters are tested and characterized along different directions, revealing that the mechanical property anisotropy is significantly affected by heat treatment due to differences in grain morphology, microtexture, recrystallization degree and secondary particles characteristics in different directions. The anisotropy is mainly influenced by the increase of number density and distribution uniformity of T-1 phase after aging treatment, as well as the elimination of PFZ and the increase of grain boundary strength.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Chemistry, Physical

The crystallographic corrosion and its microstructure in an Al-Cu-Li alloy

Jiaying Huang et al.

Summary: The study systematically investigated the localized corrosion behavior and microstructure of an Al-2.23Cu-0.96Li (wt%) alloy using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). It was found that the GPB zones in the alloy do not significantly affect the overall propagation direction of crystallographic corrosion, but are closely related to the formation of nanoscale localized corrosion morphology in the crystallographic corrosion.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Development and Application Prospects of Aluminum-Lithium Alloys in Aircraft and Space Technology

E. N. Kablov et al.

Summary: The development of contemporary aviation and space technology relies on the use of new materials, such as aluminum-lithium alloys, which provide significant weight reduction, high strength, corrosion resistance, and good weldability.

METALLURGIST (2021)

Add to Collection

Article Chemistry, Physical

Investigation on the ageing behaviour and hardening mechanisms of 5A90 Al-Li alloy U-shaped parts formed by electric resistance heating forming-quenching process

Yongkang Liu et al.

Summary: The electric resistance heating technology was introduced to improve the dimensional accuracy of 5A90 Al-Li alloy U-shaped parts. The current density significantly affected the forming quality, springback, and mechanical properties of the parts. The hardness increase was mainly attributed to the delta' phase precipitation hardening mechanism.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Chemistry, Physical

An insight into the precipitate evolution and mechanical properties of a novel high-performance cast Al-Li-Cu-Mg-X alloy

Guohua Wu et al.

Summary: This study investigated the microstructural evolution, coarsening kinetics of main precipitates, and related mechanical characteristics of a newly-developed cast Al-Li-Cu-Mg-X alloy during aging at different temperatures. The increasing aging temperature led to significantly enhanced coarsening rate of the delta' phase, resulting in a decrease in strength. The best combination of strength and ductility was achieved in the alloy aged at 175 degrees C for 32 hours.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Mechanical properties and microstructure evolution of an Al-Cu-Li alloy subjected to rolling and aging

Wang Lin et al.

Summary: Al-Cu-Li alloy sheets processed through cryorolling followed by aging exhibit high dislocation densities and a large number of precipitates, resulting in high ultimate tensile strength. On the other hand, samples processed through hot rolling followed by aging show a high uniform elongation rate. Gradual increase in precipitate size with aging time significantly affects the interaction mechanism between dislocations and precipitates.

JOURNAL OF CENTRAL SOUTH UNIVERSITY (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of Li addition on mechanical properties and ageing precipitation behavior of extruded Al-3.0Mg-0.5Si alloy

Yang Xiao-kun et al.

Summary: The addition of Li significantly improves the tensile strength and elasticity modulus of the alloy, but decreases ductility and changes the fracture mechanism; Li also alters the precipitation behavior of the alloy, with delta'-Al3Li becoming the main precipitates.

JOURNAL OF CENTRAL SOUTH UNIVERSITY (2021)

Add to Collection

Article Thermodynamics

Evaluation of pyrolysis and combustion products from foundry binders: potential hazards in metal casting

Angelika Kmita et al.

JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of ageing treatments on the precipitation behavior and mechanical properties of Al-Cu-Li alloys

Jinjun Xu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Nanoscience & Nanotechnology

On the relationship between internal porosity and the tensile ductility of aluminium alloy die-castings

Ewan Lordan et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Chemistry, Physical

Study on micro-structure, solid solubility and tensile properties of 5A90 Al-Li alloy cast by low-frequency electromagnetic casting processing

Fuyue Wang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

The Effect of Hydrogen on Pore Formation in Aluminum Alloy Castings: Myth Versus Reality

Murat Tiryakioglu

METALS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation and measurement of porosity in Al+4.5Cu/6wt%TiB2 in situ composite: optimization and statistical modelling

Shaik Mozammil et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of double-step homogenization treatments on the microstructure and mechanical properties of Al-Cu-Li-Zr alloy

Yunlai Deng et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Chemistry, Physical

Characterization and Analysis of Porosities in High Pressure Die Cast Aluminum by Using Metallography, X-Ray Radiography, and Micro-Computed Tomography

Ahmad Nourian-Avval et al.

MATERIALS (2020)

Add to Collection

Article Multidisciplinary Sciences

Mechanical and microstructural characterization of aluminum melted with alternative method

F. Severiano et al.

SN APPLIED SCIENCES (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Micro-Structure and Mechanical Properties of 2A97 Al-Li Alloy Cast by Low-Frequency Electromagnetic Casting

Fuyue Wang et al.

METALS (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Atomic size and chemical effects of alloying elements Cu, Mg and Si on the structure and dynamics of molten 8090-based AlLi alloy

Xunming Zhu et al.

INTERNATIONAL JOURNAL OF CAST METALS RESEARCH (2018)

Add to Collection

Article Chemistry, Analytical

Evolved gas analysis of PEP-SET sand by TG and FTIR

Xinyi Zhao et al.

JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural evolution and mechanical properties of cast Al-2Li-2Cu-0.5Mg-0.2Zr alloy during heat treatment

Xiaolong Zhang et al.

MATERIALS CHARACTERIZATION (2017)

Add to Collection

Article Automation & Control Systems

Forming performance of an as-quenched novel aluminum-lithium alloy

Huaguan Li et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)

Add to Collection

Review Metallurgy & Metallurgical Engineering

Melting and casting of lithium containing aluminium alloys

N. Akhtar et al.

INTERNATIONAL JOURNAL OF CAST METALS RESEARCH (2015)

Add to Collection

Article Nanoscience & Nanotechnology

Porosity, hydrogen and bifilm content in Al alloy castings

D. Dispinar et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)

Add to Collection

Article Nanoscience & Nanotechnology

Development and characterization of Al-Li alloys

RK Gupta et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)

Add to Collection

Article Engineering, Industrial

Effect of melt cleanliness on the formation of porosity defects in automotive aluminium high pressure die castings

C Tian et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2002)

Add to Collection

© Peeref 2019-2024. All rights reserved.