☆ 4.6 Article

Development of a phased array ultrasound roller probe for inspection of wire plus arc additive manufactured components

JOURNAL OF MANUFACTURING PROCESSES (2022)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Steel-copper functionally graded material produced by twin-wire and arc additive manufacturing (T-WAAM)

Tiago A. Rodrigues et al.

Summary: A functionally graded material (FGM) part was successfully fabricated using twin-wire and arc additive manufacturing (T-WAAM) process, with retained d-ferrite found in a Cu matrix and a smooth gradient of hardness and electric conductivity along the FGM sample height. The FGM part exhibited an ultimate tensile strength of 690 MPa and an elongation at fracture of 16.6%.

MATERIALS & DESIGN (2022)

Add to Collection

Article Engineering, Manufacturing

Investigating the effect of residual stress on hydrogen cracking in multi-pass robotic welding through process compatible non-destructive testing

Yashar Javadi et al.

Summary: This study investigated the effect of welding residual stress (WRS) on hydrogen-induced cracks (HIC) and found that higher WRS resulted in larger size and number of HIC. Real-time monitoring of the negative impact of WRS on HIC was achieved using high-temperature in-process inspection for the first time.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Automation & Control Systems

A Phased Array Ultrasound Roller Probe for Automated in-Process/Interpass Inspection of Multipass Welds

Randika K. W. Vithanage et al.

Summary: Traditional non-destructive inspection of multi-pass welds can be complicated and costly, but a novel high-temperature ultrasound phased array roller probe allows for in-process inspection to identify defects earlier and has the potential for industrialization in the future.

IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS (2021)

Add to Collection

Review Engineering, Manufacturing

A review on wire and arc additive manufacturing of titanium alloy

Zidong Lin et al.

Summary: Wire and arc additive manufacturing (WAAM) is an economic and efficient technology suitable for producing large-scale metallic components, particularly in the fabrication of near-net-shape and large-scale titanium alloys. It has been significantly noticed and adopted due to its high deposition rate, low machinery cost, and shortened lead time compared to other powder-based additive manufacturing techniques.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Increasing the manufacturing efficiency of WAAM by advanced cooling strategies

Uwe Reisgen et al.

WELDING IN THE WORLD (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Wire arc additive manufacturing Ti6Al4V aeronautical parts using plasma arc welding: Analysis of heat-treatment processes in different atmospheres

Teresa Artaza et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Chemistry, Multidisciplinary

Nondestructive Ultrasonic Inspection of Composite Materials: A Comparative Advantage of Phased Array Ultrasonic

Hossein Taheri et al.

APPLIED SCIENCES-BASEL (2019)

Add to Collection

Article Materials Science, Characterization & Testing

Phased Array Ultrasonic Inspection of Metal Additive Manufacturing Parts

Ana Beatriz Lopez et al.

JOURNAL OF NONDESTRUCTIVE EVALUATION (2019)

Add to Collection

Article Materials Science, Multidisciplinary

On the origin of microstructural banding in Ti-6Al4V wire-arc based high deposition rate additive manufacturing

Alistair Ho et al.

ACTA MATERIALIA (2019)

Add to Collection

Article Chemistry, Physical

Optimising the mechanical properties of Ti-6Al-4V components produced by wire plus arc additive manufacturing with post-process heat treatments

M. J. Bermingham et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Review Engineering, Manufacturing

A review of the wire arc additive manufacturing of metals: properties, defects and quality improvement

Bintao Wu et al.

JOURNAL OF MANUFACTURING PROCESSES (2018)

Add to Collection

Review Materials Science, Multidisciplinary

The metallurgy and processing science of metal additive manufacturing

W. J. Sames et al.

INTERNATIONAL MATERIALS REVIEWS (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Wire plus Arc Additive Manufacturing

S. W. Williams et al.

MATERIALS SCIENCE AND TECHNOLOGY (2016)

Add to Collection

Article Automation & Control Systems

Wire-feed additive manufacturing of metal components: technologies, developments and future interests

Donghong Ding et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)

Add to Collection

Proceedings Paper Engineering, Industrial

Review of Non-destructive Testing (NDT) Techniques and their applicability to thick walled composites

M. R. Jolly et al.

PROCEEDINGS OF THE 4TH INTERNATIONAL CONFERENCE ON THROUGH-LIFE ENGINEERING SERVICES (2015)

Add to Collection

Article Engineering, Industrial

Investigation of the benefits of plasma deposition for the additive layer manufacture of Ti-6Al-4V

F. Martina et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2012)

Add to Collection

© Peeref 2019-2024. All rights reserved.