Related references
Note: Only part of the references are listed.Toward online layer-wise surface morphology measurement in additive manufacturing using a deep learning-based approach
Chenang Liu et al.
JOURNAL OF INTELLIGENT MANUFACTURING (2023)
In-situ synchrotron X-ray analysis of metal Additive Manufacturing: Current state, opportunities and challenges
Chrysoula Ioannidou et al.
MATERIALS & DESIGN (2022)
In Situ Analysis of Laser Powder Bed Fusion Using Simultaneous High-Speed Infrared and X-ray Imaging
Benjamin Gould et al.
JOM (2021)
Use of 450-808 nm diode lasers for efficient energy absorption during powder bed fusion of Ti6Al4V
Mohammed Alsaddah et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)
A critical look at the prediction of the temperature field around a laser-induced melt pool on metallic substrates
Yi Shu et al.
SCIENTIFIC REPORTS (2021)
A new ray tracing heat source model for mesoscale CFD simulation of selective laser melting (SLM)
Binqi Liu et al.
APPLIED MATHEMATICAL MODELLING (2020)
Influence of Scan Strategy on Porosity and Microstructure of Ti-6Al-4V Fabricated by Electron Beam Powder Bed Fusion
Peeyush Nandwana et al.
Materials Today Communications (2020)
Precise Measurements of Thermophysical Properties of Liquid Ti-6Al-4V (Ti64) Alloy On Board the International Space Station
Markus Mohr et al.
ADVANCED ENGINEERING MATERIALS (2020)
In-Situ Defect Detection in Laser Powder Bed Fusion by Using Thermography and Optical Tomography-Comparison to Computed Tomography
Gunther Mohr et al.
METALS (2020)
Investigation of Melt Pool Geometry Control in Additive Manufacturing Using Hybrid Modeling
Sudeepta Mondal et al.
METALS (2020)
Temperature Measurement of Laser-Irradiated Metals Using Hyperspectral Imaging
Dong-Xia Qu et al.
PHYSICAL REVIEW APPLIED (2020)
Processing parameters in laser powder bed fusion metal additive manufacturing
J. P. Oliveira et al.
MATERIALS & DESIGN (2020)
Melting behavior in laser powder bed fusion revealed by in situ X-ray and thermal imaging
Yuki Wakai et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)
Layer-wise spatial modeling of porosity in additive manufacturing
Jia (Peter) Liu et al.
IISE TRANSACTIONS (2019)
Keyhole threshold and morphology in laser melting revealed by ultrahigh-speed x-ray imaging
Ross Cunningham et al.
SCIENCE (2019)
High-speed X-ray investigation of melt dynamics during continuous-wave laser remelting of selective laser melted Co-Cr alloy
Brodan Richter et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2019)
Dynamics of pore formation during laser powder bed fusion additive manufacturing
Aiden A. Martin et al.
NATURE COMMUNICATIONS (2019)
Integrated Simulation Framework for Additively Manufactured Ti-6Al-4V: Melt Pool Dynamics, Microstructure, Solid-State Phase Transformation, and Microelastic Response
Rongpei Shi et al.
JOM (2019)
Assessing printability maps in additive manufacturing of metal alloys
Luke Johnson et al.
ACTA MATERIALIA (2019)
Benchmark Study of Thermal Behavior, Surface Topography, and Dendritic Microstructure in Selective Laser Melting of Inconel 625
Zhengtao Gan et al.
INTEGRATING MATERIALS AND MANUFACTURING INNOVATION (2019)
Transient dynamics of powder spattering in laser powder bed fusion additive manufacturing process revealed by in-situ high-speed high-energy x-ray imaging
Qilin Guo et al.
ACTA MATERIALIA (2018)
On the Simulation Scalability of Predicting Residual Stress and Distortion in Selective Laser Melting
C. Li et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2018)
Measurement of the Melt Pool Length During Single Scan Tracks in a Commercial Laser Powder Bed Fusion Process
J. C. Heigel et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2018)
Additive manufacturing of metallic components - Process, structure and properties
T. DebRoy et al.
PROGRESS IN MATERIALS SCIENCE (2018)
In situ X-ray imaging of defect and molten pool dynamics in laser additive manufacturing
Chu Lun Alex Leung et al.
NATURE COMMUNICATIONS (2018)
Ultrafast X-ray imaging of laser-metal additive manufacturing processes
Niranjan D. Parab et al.
JOURNAL OF SYNCHROTRON RADIATION (2018)
Additive manufacturing of metals: a brief review of the characteristic microstructures and properties of steels, Ti-6Al-4V and high-entropy alloys
Stephane Gorsse et al.
SCIENCE AND TECHNOLOGY OF ADVANCED MATERIALS (2017)
Microstructure evolution and EBSD analysis of a graded steel fabricated by laser additive manufacturing
Qiang Wang et al.
VACUUM (2017)
Ror2 signaling regulates Golgi structure and transport through IFT20 for tumor invasiveness
Michiru Nishita et al.
SCIENTIFIC REPORTS (2017)
Localized melt-scan strategy for site specific control of grain size and primary dendrite arm spacing in electron beam additive manufacturing
Narendran Raghavan et al.
ACTA MATERIALIA (2017)
Numerical modeling of heat-transfer and the influence of process parameters on tailoring the grain morphology of IN718 in electron beam additive manufacturing
Narendran Raghavan et al.
ACTA MATERIALIA (2016)
Microstructural Control of Additively Manufactured Metallic Materials
P. C. Collins et al.
ANNUAL REVIEW OF MATERIALS RESEARCH, VOL 46 (2016)
HiSPoD: a program for high-speed polychromatic X-ray diffraction experiments and data analysis on polycrystalline samples
Tao Sun et al.
JOURNAL OF SYNCHROTRON RADIATION (2016)
Finite Element Simulation of Selective Laser Melting process considering Optical Penetration Depth of laser in powder bed
Ali Foroozmehr et al.
MATERIALS & DESIGN (2016)
In-process sensing in selective laser melting (SLM) additive manufacturing
Thomas G. Spears et al.
INTEGRATING MATERIALS AND MANUFACTURING INNOVATION (2016)
A review on selective laser sintering/melting (SLS/SLM) of aluminium alloy powders: Processing, microstructure, and properties
E. O. Olakanmi et al.
PROGRESS IN MATERIALS SCIENCE (2015)
Simultaneous X-ray diffraction and phase-contrast imaging for investigating material deformation mechanisms during high-rate loading
M. Hudspeth et al.
JOURNAL OF SYNCHROTRON RADIATION (2015)
Site specific control of crystallographic grain orientation through electron beam additive manufacturing
R. R. Dehoff et al.
MATERIALS SCIENCE AND TECHNOLOGY (2015)
Possibilities of CT scanning as analysis method in laser additive manufacturing
Aleksis Karme et al.
15TH NORDIC LASER MATERIALS PROCESSING CONFERENCE, NOLAMP 15 (2015)
Transient x-ray diffraction with simultaneous imaging under high strain-rate loading
D. Fan et al.
REVIEW OF SCIENTIFIC INSTRUMENTS (2014)
Residual stress via the contour method in compact tension specimens produced via selective laser melting
Bey Vrancken et al.
SCRIPTA MATERIALIA (2014)
Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder
Lore Thijs et al.
ACTA MATERIALIA (2013)
Investigation of laser consolidation process for metal powder by two-color pyrometer and high-speed video camera
Tatsuaki Furumoto et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2013)
Finite element simulation of the temperature and stress fields in single layers built without-support in selective laser melting
Ahmed Hussein et al.
MATERIALS & DESIGN (2013)
Increasing Solar Absorption for Photocatalysis with Black Hydrogenated Titanium Dioxide Nanocrystals
Xiaobo Chen et al.
SCIENCE (2011)
3D Digitization of Metallic Specular Surfaces using Scanning from Heating Approach
Alban Bajard et al.
THREE-DIMENSIONAL IMAGING, INTERACTION, AND MEASUREMENT (2011)
Analysis and compensation of rolling shutter effect
Chia-Kai Liang et al.
IEEE TRANSACTIONS ON IMAGE PROCESSING (2008)
Ultrafast X-ray phase-contrast imaging of the initial coalescence phase of two water droplets
Kamel Fezzaa et al.
PHYSICAL REVIEW LETTERS (2008)
Process modeling in laser deposition of multilayer SS410 steel
Liang Wang et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2007)
Phase transformation dynamics during welding of Ti-6Al-4V
JW Elmer et al.
JOURNAL OF APPLIED PHYSICS (2004)