☆ 4.6 Article

On the Numerical Modeling of Flax/PLA Bumper Beams

MATERIALS (2022)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Influence of cross-section on the impact and post-impact behavior of biocomposites bumper beams

Liu Jiao-Wang et al.

Summary: This work aims to analyze the influence of the cross-section shape of a fully biodegradable composite bumper beam. Flax/PLA bumper beams with four different degrees of roundness were manufactured. Specimens were subjected to low velocity impacts and the post-impact behavior was evaluated through three-point bending tests. The results indicate that different cross-section shapes can be selected depending on whether the objective is to maximize impact performance or post-impact residual properties.

MECHANICS OF ADVANCED MATERIALS AND STRUCTURES (2023)

Add to Collection

Article Materials Science, Textiles

Fabrication of Automobile Component Using Hybrid Natural Fiber Reinforced Polymer Composite

Rajkumar Ramasubbu et al.

Summary: In recent years, natural fibers have been increasingly used for their lower weight to strength ratio, low cost, and environmental-friendly attributes. In this study, a hybrid composite (HC) was manufactured using sisal/kenaf fiber reinforced with epoxy matrix, and its mechanical properties were compared with sisal fiber composite (SFC) and kenaf fiber composite (KFC). The results showed that HC exhibited better properties, making it suitable for lightweight automobile applications.

JOURNAL OF NATURAL FIBERS (2022)

Add to Collection

Article Chemistry, Physical

Performance Evaluation of Jute/Glass-Fiber-Reinforced Polybutylene Succinate (PBS) Hybrid Composites with Different Layering Configurations

Muhammad Usman Ghani et al.

Summary: The effect of stacking sequence on the performance of glass-jute hybrid composites was studied. Composites with glass fiber layers on their outer surfaces showed the best mechanical, thermal, and water resistance properties.

MATERIALS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of stacking sequence and fiber content on mechanical and morphological properties of woven kenaf/polyester fiber reinforced polylactic acid (PLA) hybrid laminated composites

M. N. M. Azlin et al.

Summary: Hybrid laminated composites consisting of woven kenaf, woven polyester, and polylactic acid (PLA) were fabricated using the hot compression method. The composition and stacking sequence of the hybrid composites significantly influenced their mechanical properties. Increasing the content of woven kenaf improved the flexural properties of the hybrid composites, while the composition of woven kenaf and woven polyester had an effect on flexural strength. Additionally, the tensile fracture surface morphology was evaluated using field emission scanning electron microscopy (FESEM), providing insights for industrial applications.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Computer Science, Interdisciplinary Applications

Drilling of biocomposite materials: Modelling and experimental validation

A. Diaz-Alvarez et al.

Summary: This study compared the induced damage during drilling of biocomposites and traditional composites, finding that induced damage decreases with feed rate in biocomposites while it increases in traditional composites. Experimental tests confirmed the results, showing that constitutive model accounts for the behavior observed in biocomposites. The numerical model was able to reproduce the effect of cutting conditions observed during experimental tests on induced damage during drilling.

SIMULATION MODELLING PRACTICE AND THEORY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Biomimetic approaches towards lightweight composite structures for car interior parts

Katrin Greta Hoffmann et al.

Summary: Natural fibre-reinforced plastic composites made from fleeces and felts are commonly used in automotive interior parts due to their good density specific mechanical properties and low carbon footprint. By employing a biomimetic technology-pull approach, natural fibre-reinforced polypropylene plates with improved lightweight potential were produced, with the best results achieved using a sandwich structure surrounding a needle felt core.

MATERIALS & DESIGN (2021)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Numerical analysis of natural fiber reinforced composite bumper

N. Murugu Nachippan et al.

Summary: This study focuses on the static analysis of using natural fiber reinforced composite materials to manufacture car bumpers. The research found that glass fiber treated hemp fiber reinforced epoxy composites exhibit minimal deformation, making them the most suitable for automobile bumpers.

MATERIALS TODAY-PROCEEDINGS (2021)

Add to Collection

Article Mechanics

Analysis of orthogonal cutting of biocomposites

A. Diaz-Alvarez et al.

COMPOSITE STRUCTURES (2020)

Add to Collection

Article Mechanics

Energy absorption and residual bending behavior of biocomposites bumper beams

A. Diaz-Alvarez et al.

COMPOSITE STRUCTURES (2020)

Add to Collection

Article Materials Science, Composites

Effect of processing temperature on the static and dynamic mechanical properties and failure mechanisms of flax fiber reinforced composites

Qian Li et al.

COMPOSITES COMMUNICATIONS (2020)

Add to Collection

Article Mechanics

Low-velocity impact behaviour of green epoxy biocomposite laminates reinforced by sisal fibers

C. Militello et al.

COMPOSITE STRUCTURES (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Rheological and thermal behavior of PHB/piassava fiber residue-based green composites modified with warm water

Eduardo Braga Costa Santos et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2019)

Add to Collection

Article Mechanics

Analysis of low-velocity impact on flax/PLA composites using a strain rate sensitive model

E. Jalon et al.

COMPOSITE STRUCTURES (2018)

Add to Collection

Article Chemistry, Physical

Energy Absorption Capacity in Natural Fiber Reinforcement Composites Structures

Elias Lopez-Alba et al.

MATERIALS (2018)

Add to Collection

Proceedings Paper Engineering, Multidisciplinary

Simulation and Failure Analysis of Car Bumper Made of Pineapple Leaf Fiber Reinforced Composite

E. S. Arbintarso et al.

2ND INTERNATIONAL CONFERENCE ON INNOVATION IN ENGINEERING AND VOCATIONAL EDUCATION (2018)

Add to Collection

Article Mechanics

Constitutive model to predict the viscoplastic behaviour of natural fibres based composites

A. Rubio-Lopez et al.

COMPOSITE STRUCTURES (2016)

Add to Collection

Article Mechanics

Modelling impact behaviour of all-cellulose composite plates

A. Rubio-Lopez et al.

COMPOSITE STRUCTURES (2015)

Add to Collection

Article Engineering, Multidisciplinary

Development and characterization of a laminate composite material from polylactic acid (PLA) and woven bamboo fabric

A. Porras et al.

COMPOSITES PART B-ENGINEERING (2012)

Add to Collection

© Peeref 2019-2024. All rights reserved.