☆ 4.7 Article

Evaluation and classification of CFRP kerf width by acoustic emission in nanosecond laser cutting

OPTICS AND LASER TECHNOLOGY (2022)

Related references

Note: Only part of the references are listed.

Article Optics

Simulation, statistical modeling, and optimization of CO2 laser cutting process of polycarbonate sheets

Mahmoud Moradi et al.

Summary: This study utilized numerical simulation and statistical analysis to investigate the effects of laser cutting process parameters on polycarbonate sheets. Results showed that cutting speed significantly influenced the top kerf width, with optimal parameters minimizing taper kerf. Increasing cutting speed and decreasing laser power reduced the heat-affected zone. The developed analysis can accurately predict kerf depth for different laser parameters.

OPTIK (2021)

Add to Collection

Article Engineering, Multidisciplinary

Structural condition monitoring and identification of laser cladding metallic panels based on an acoustic emission signal feature optimization algorithm

Yang Li et al.

Summary: The study focuses on monitoring and identifying the laser cladding processing condition of metallic panels using acoustic emission technology. A new method for feature extraction and optimization of acoustic emission signals is proposed, which effectively improves the identification rate of classification. The feasibility of the proposed method for analyzing laser cladding acoustic emission signal characteristics is verified, showing the effectiveness of acoustic emission-based structural condition monitoring and identification of laser cladding plate-like structures.

STRUCTURAL HEALTH MONITORING-AN INTERNATIONAL JOURNAL (2021)

Add to Collection

Article Mechanics

UV laser high-quality drilling of CFRP plate with a new interlaced scanning mode

Wenyuan Li et al.

Summary: An interlaced scanning mode (ISM) is proposed to improve the surface quality of carbon fibre reinforced polymers (CFRP) plate by reducing heat accumulation effect and surface defects compared to the default sequential scanning mode (SSM). Several experiments show that ISM can significantly reduce the overall average HAZ width and taper of the hole, leading to less damage in the HAZ and vicinity.

COMPOSITE STRUCTURES (2021)

Add to Collection

Article Optics

Thermal ablation regulation for ultraviolet (UV) nanosecond laser precision cutting of polycarbonate (PC) film

Congyi Wu et al.

Summary: The study focused on the UV nanosecond laser cutting of PC films, evaluating the cutting mechanism and analyzing the influence of process parameters on cutting quality through orthogonal experiments. The optimal parameter combination resulted in smaller cutting seam width and heat-affected zone width without obvious seam taper.

OPTICS AND LASER TECHNOLOGY (2021)

Add to Collection

Article Optics

High-quality cutting polarizing film (POL) by 355 nm nanosecond laser ablation

Youmin Rong et al.

Summary: With the development of ultra-high screen-to-body ratio liquid crystal display (LCD) screen, the cutting quality of LCD screen polarized film (POL) has become extremely important. High-quality cutting was achieved using a 355 nm (ultraviolet light) nanosecond laser, and the cutting quality was analyzed with laser ablation process as the core. The study also summarized the cutting mechanism of POL with laser ablation as the core by analyzing the thermal decomposition process of POL, and examined the effects of manufacturing parameters on cutting quality based on experimental results and laser ablation mechanism.

OPTICS AND LASER TECHNOLOGY (2021)

Add to Collection

Article Engineering, Industrial

Monitoring method for femtosecond laser modification of silicon carbide via acoustic emission techniques

Xiaozhu Xie et al.

Summary: The study analyzed the process of femtosecond laser modification of silicon carbide surface using acoustic emission analysis, revealing that the material removal of SiC surface ablated by fs-laser increases with the laser fluence, and the correlation between AE signals and surface structure characteristics.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection

Article Engineering, Manufacturing

Semi-supervised Monitoring of Laser powder bed fusion process based on acoustic emissions

Vigneashwara Pandiyan et al.

Summary: Metal-based Laser Powder Bed Fusion (LPBF) technology requires quality monitoring due to repeatability issues. A common method for monitoring uses Machine Learning algorithms, but an alternative semi-supervised approach is proposed in this article. By familiarizing ML algorithms only with acoustic signatures corresponding to defect-free regimes, anomalies can be classified with high accuracy.

VIRTUAL AND PHYSICAL PROTOTYPING (2021)

Add to Collection

Article Engineering, Mechanical

Examination of undisturbed acoustic emission generated by experimentally modelled two-body abrasive wear events

Michael Haas et al.

TRIBOLOGY INTERNATIONAL (2020)

Add to Collection

Article Optics

Experimental and parametric evaluation of cut quality characteristics in CO2 laser cutting of polystyrene

Elyas Haddadi et al.

OPTIK (2019)

Add to Collection

Review Engineering, Multidisciplinary

The fatigue of carbon fibre reinforced plastics - A review

Parvez Alam et al.

COMPOSITES PART B-ENGINEERING (2019)

Add to Collection

Article Engineering, Multidisciplinary

Optimization of machining parameters in turning Nimonic-75 using machine vision and acoustic emission signals by Taguchi technique

Y. D. Chethan et al.

MEASUREMENT (2019)

Add to Collection

Article Automation & Control Systems

Defect classification of laser metal deposition using logistic regression and artificial neural networks for pattern recognition

Haythem Gaja et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Automation & Control Systems

Study on burr occurrence and surface integrity during slot milling of multidirectional and plain woven CFRPs

Maojun Li et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Optics

Enhancement of low power CO2 laser cutting process for injection molded polycarbonate

Mahmoud Moradi et al.

OPTICS AND LASER TECHNOLOGY (2017)

Add to Collection

Article Engineering, Multidisciplinary

Application of acoustic emission sensor to investigate the frequency of tool wear and plastic deformation in tool condition monitoring

M. S. H. Bhuiyan et al.

MEASUREMENT (2016)

Add to Collection

Review Engineering, Manufacturing

Modeling of machining of composite materials: A review

Chinmaya R. Dandekar et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2012)

Add to Collection

Article Instruments & Instrumentation

AE signals as laser cutting quality indicators

T. Kek et al.

INSIGHT (2009)

Add to Collection

Review Engineering, Manufacturing

Laser beam machining - A review

Avanish Kumar Dubey et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)

Add to Collection

© Peeref 2019-2024. All rights reserved.