Related references
Note: Only part of the references are listed.Effects of fine grains and sintering additives on stereolithography additive manufactured Al2O3 ceramic
Keqiang Zhang et al.
CERAMICS INTERNATIONAL (2021)
Additive manufacturing of advanced ceramic materials
Y. Lakhdar et al.
PROGRESS IN MATERIALS SCIENCE (2021)
Evaluation of the morphology and pore characteristics of silica refractory using X-ray computed tomography
Jiahang Fan et al.
CERAMICS INTERNATIONAL (2021)
Dynamic response and damage evolution of Zr-based bulk metallic glass under shock loading
Yan Li et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)
Stereolithography additive manufacturing of multi-ceramic triangle structures with tunable thermal expansion
Keqiang Zhang et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)
Digital light processing fabrication of mullite component derived from preceramic precusor using photosensitive hydroxysiloxane as the matrix and alumina nanoparticles as the filler
Chong He et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)
Additive manufacturing of structural materials
Guo Liu et al.
MATERIALS SCIENCE & ENGINEERING R-REPORTS (2021)
Effects of solid loading on stereolithographic additive manufactured ZrO2 ceramic: A quantitative defect study by X-ray computed tomography
Keqiang Zhang et al.
CERAMICS INTERNATIONAL (2021)
X-ray tomography of additive-manufactured zirconia: Processing defects - Strength relations
M. Saadaoui et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)
Dispersion and stability of SiC ceramic slurry for stereolithography
Guojiao Ding et al.
CERAMICS INTERNATIONAL (2020)
Fabrication of complex shaped alumina parts by gelcasting on 3D printed moulds
Sindi Sithembiso Ndinisa et al.
CERAMICS INTERNATIONAL (2020)
Preparation of porous Al2O3 ceramics with enhanced properties by SLS using Al2O3 poly-hollow microspheres (PHMs) coated with CaSiO3 sintering additive
Jia-Min Wu et al.
CERAMICS INTERNATIONAL (2020)
Additive manufacturing of hydroxyapatite bioceramic scaffolds: Dispersion, digital light processing, sintering, mechanical properties, and biocompatibility
Chengwei Feng et al.
JOURNAL OF ADVANCED CERAMICS (2020)
Preliminary 3D printing of large inclined-shaped alumina ceramic parts by direct ink writing
Liangliang Yang et al.
JOURNAL OF ADVANCED CERAMICS (2020)
Analysis of the effect of surface roughness on fatigue performance of powder bed fusion additive manufactured metals
Niloofar Sanaei et al.
THEORETICAL AND APPLIED FRACTURE MECHANICS (2020)
Additive manufacturing of silica aerogels
Shanyu Zhao et al.
NATURE (2020)
Synergy of solid loading and printability of ceramic paste for optimized properties of alumina via stereolithography-based 3D printing
Weiwei Liu et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)
Direct ink writing additive manufacturing of porous alumina-based ceramic cores modified with nanosized MgO
Shiyan Tang et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)
High solid loading, low viscosity photosensitive Al2O3 slurry for stereolithography based additive manufacturing
Keqiang Zhang et al.
CERAMICS INTERNATIONAL (2019)
Influence of boundary masks on dimensions and surface roughness using segmented exposure in ceramic 3D printing
Xiangquan Wu et al.
CERAMICS INTERNATIONAL (2019)
Deep Learning Techniques for Medical Image Segmentation: Achievements and Challenges
Mohammad Hesam Hesamian et al.
JOURNAL OF DIGITAL IMAGING (2019)
Detection of small delamination in mullite/Si/SiC model EBC system by pulse thermography
Yutaro Arai et al.
JOURNAL OF ADVANCED CERAMICS (2019)
Characterization of high-pressure die-cast hypereutectic Al-Si alloys based on microstructural distribution and fracture morphology
X. Y. Jiao et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)
3D printing of ceramics: A review
Zhangwei Chen et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)
Complex mullite structures fabricated via digital light processing of a preceramic polysiloxane with active alumina fillers
Johanna Schmidt et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)
3D printing of complex shaped alumina parts
Sirisala Mamatha et al.
CERAMICS INTERNATIONAL (2018)
Effect of plasticizer on the fabrication and properties of alumina ceramic by stereolithography-based additive manufacturing
Zhanwen Xing et al.
CERAMICS INTERNATIONAL (2018)
3D PRINTING Additive manufacturing of polymer-derived ceramics
Zak C. Eckel et al.
SCIENCE (2016)
Shaping of engineering ceramics by electro, chemical and physical processes
Eleonora Ferraris et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2016)
3D quantitative analysis of graphite morphology in high strength cast iron by high-energy X-ray tomography
Chihpin Chuang et al.
SCRIPTA MATERIALIA (2015)
Direct selective laser sintering/melting of high density alumina powder layers at elevated temperatures
J. Deckers et al.
8TH INTERNATIONAL CONFERENCE ON LASER ASSISTED NET SHAPE ENGINEERING (LANE 2014) (2014)
Surface roughness analysis, modelling and prediction in selective laser melting
Giovanni Strano et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2013)
Density improvement of alumina parts produced through selective laser sintering of alumina-polyamide composite powder
Jan Deckers et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2012)