☆ 4.5 Article

Characteristics of Torch-Offset Cold Metal Transition-Cycle Step Welding of 5052Al Alloy with T2 Copper via Al-12Si Filler

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Dissimilar laser spot welding of aluminum alloy to steel in keyhole mode

Rui Xiao et al.

Summary: This study investigated the dissimilar joining of aluminum alloy to steel using laser spot welding in the keyhole mode. The results showed that the defocusing amount and laser power significantly influenced the formation of the weld. The aluminum alloy was prone to welding defects, but placing a copper heat sink under the aluminum alloy effectively absorbed the heat and reduced the defects. The study also investigated the influence of laser power, defocusing amount, welding time, and shielding gas on the joint characteristics. Microstructure analysis revealed the formation of a conelike fusion zone and sparsely distributed Fe-Al intermetallic compounds. The laser keyhole spot welds achieved a combination of metallurgical bonding and mechanical interlocking, leading to improved joint mechanical properties.

JOURNAL OF LASER APPLICATIONS (2022)

Add to Collection

Review Engineering, Industrial

Laser techniques for dissimilar joining of aluminum alloys to steels: A critical review

Jin Yang et al.

Summary: The use of multi-material structures is an effective solution to reduce weight and emissions in the automotive industry. However, joining aluminum alloys to steels is challenging due to their mismatched properties. Laser-based processes have been explored to overcome this issue and this review examines the recent achievements and progress in this field, evaluating factors such as joining conditions, filler materials, microstructure, and mechanical properties.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

Add to Collection

Article Engineering, Industrial

Enhancing the wettability for 4043 aluminum alloy on 301L stainless steel via chemical-etched surface texturing

Haoyue Li et al.

Summary: Chemical-etched surface texturing has a significant impact on wetting behavior, improving the wettability of aluminum/stainless steel by adjusting surface roughness. This study provides guidance for processing technologies such as brazing, welding, and coating.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

Add to Collection

Article Chemistry, Physical

Influence of porous high entropy alloy coating on wetting behavior and interfacial microstructure of Al-Si alloy on steel substrate

Min Zheng et al.

Summary: A porous FeCoNiCr high entropy alloy (HEA) coating was prepared on a steel substrate via vacuum sintering. The wetting behavior of liquid Al-12Si alloy over the coated and uncoated steel substrate was comparatively analyzed. The results showed that the porous coating enhanced the capillary force and facilitated the infiltration and spread of the liquid alloy, resulting in improved wettability and suppressed interfacial intermetallic compound (IMC) formation.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Optics

Effect of heat input on interfacial microstructure, tensile and bending properties of dissimilar Al/steel lap joints by laser Welding-brazing

Yang Jin et al.

Summary: The study found that with the increase of laser power, the fracture load of laser Al/steel joints first increased and then reached a plateau, but the laser power had limited influence on the joint's bending property due to the formation of tough FeZn10. Numerical simulation showed that the interfacial temperature varied with the increasing laser power, resulting in the change of IMCs layer.

OPTICS AND LASER TECHNOLOGY (2021)

Add to Collection

Article Optics

Experimental and numerical assessment of interfacial microstructure evolution in dissimilar Al/steel joint by diode laser welding-brazing

Ming Xiao et al.

Summary: Diode laser welding-brazing was used to lap join DP980 steel with AA 5754-O aluminum alloy, generating a composite-like reaction layer at the fusion zone/steel interface. Finite element analysis revealed the influence of vortexes on interfacial diffusion and dissolution, changing the behavior of the reaction products. This study provides insights into the formation mechanism of the interfacial reaction layer during laser welding-brazing.

OPTIK (2021)

Add to Collection

Article Optics

Effect of the scanning path on the nanosecond pulse laser welded Al/Cu lapped joint

Baohua Zhu et al.

Summary: The study showed that the outer spiral laser scanning path was the most beneficial for bonding strength, achieving a tensile-shear load of up to 198 N. A satisfactory weld formation, pinning effect due to the wave structure, and continuous interfacial IMC all contributed to the highest bonding strength of the joint.

OPTICS AND LASER TECHNOLOGY (2021)

Add to Collection

Article Engineering, Manufacturing

Interfacial microstructure and reaction mechanism with various weld fillers on laser welding-brazing of Al/Cu lap joint

Zhenglong Lei et al.

Summary: The study investigated the influence of pure Al, Al-Si, and Zn-Al weld fillers on the microstructure and mechanical properties during lap laser welding-brazing of Al to Cu. It was found that the Zn-Al weld filler effectively limited the formation of the Al2Cu brittle phase, enhancing the mechanical properties and strength of the Al/Cu joint.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Optics

Microstructure and mechanical properties of laser fusion welded Al/steel joints using a Zn-based filler wire

Jiahao Su et al.

OPTICS AND LASER TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

The Microstructure and Mechanical Properties of Multipass Friction Stir-Welded Al/Cu Lap Joints and Interface Transfer during Butt Joining of Thick Plates

Yanni Wei et al.

ADVANCED ENGINEERING MATERIALS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

On the Joint Formation and Interfacial Microstructure of Cold Metal Transfer Cycle Step Braze Welding of Aluminum to Steel Butt Joint

James Chen et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and Properties of an Al 6061/Galvanized Plate Fabricated by CMT Welding

Zhang Qi et al.

JOURNAL OF WUHAN UNIVERSITY OF TECHNOLOGY-MATERIALS SCIENCE EDITION (2020)

Add to Collection

Article Engineering, Manufacturing

Effect of the microstructure of IMCs and zinc accumulation on the mechanical properties of aluminum/galvanized steel joints in the VP-CMT process

Peizhi Xu et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection

Article Engineering, Industrial

Weld zone porosity elimination process in remote laser welding of AA5182-O aluminum alloy lap-joints

Wu Tao et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)

Add to Collection

Article Engineering, Manufacturing

Microstructural evolution and mechanical property of TC4/304 stainless steel joined by CMT using a CuSi3 filler wire

Peng Jin et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Al-Steel Joining by CMT Weld Brazing: Effect of Filler Wire Composition and Pulsing on the Interface and Mechanical Properties

Krishna P. Yagati et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2019)

Add to Collection

Article Chemistry, Physical

Effect of ultrasonic vibration on the intermetallic compound layer formation in Al/Cu friction stir weld joints

Najib A. Muhammad et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Chemistry, Physical

Wetting of T2 Cu by molten 4043 and 6061 Al alloys at 923-1023 K

Qiaoli Lin et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Influences of Friction Stir Welding and Post-Weld Heat Treatment on Al-Cu-Li Alloy

Yi Lin et al.

ADVANCED ENGINEERING MATERIALS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Cu Addition to Zn-12Al Alloy on Thermal Properties and Wettability on Cu and Al Substrates

Tomasz Gancarz et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2016)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Electron beam welding of aluminum to copper: mechanical properties and their relation to microstructure

C. Otten et al.

WELDING IN THE WORLD (2016)

Add to Collection

Article Automation & Control Systems

Dissimilar metal joining of stainless steel and titanium using copper as transition metal

Goncalo Pardal et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and properties of aluminum AA6061-T6 to copper (Cu)-T2 joints by cold metal transfer joining technology

Z. P. Cai et al.

JOURNAL OF MATERIALS RESEARCH (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructures and Properties of Aluminum-Copper Lap-Welded Joints by Cold Metal Transfer Technology

Jicai Feng et al.

ADVANCED ENGINEERING MATERIALS (2015)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of columnar-grained copper produced by the Ohno continuous casting technique

Y. H. Wang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of welding speed on microstructural and mechanical properties of laser lap weld joints in dissimilar Al and Cu sheets

S. J. Lee et al.

SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural evolution and mechanical properties of dissimilar Al-Cu joints produced by friction stir welding

C. W. Tan et al.

MATERIALS & DESIGN (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and phase constitution near the interface of Cu/Al vacuum brazing using Al-Si filler metal

Chunzhi Xia et al.

VACUUM (2008)

Add to Collection

© Peeref 2019-2024. All rights reserved.