☆ 4.7 Article

Spheroidization and dynamic recrystallization mechanisms of a novel HIPed P/M superalloy during hot deformation

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Related references

Note: Only part of the references are listed.

Article Chemistry, Physical

Hot deformation behavior and flow stress modeling of a novel CoNi-based wrought superalloy

Huiwei Li et al.

Summary: The thermal deformation behavior and flow stress modeling of a novel CoNi-based wrought superalloy were investigated at different temperatures and strain rates, showing dynamic recrystallization occurring under all deformation conditions. Additionally, when the alloy was deformed sub-solvusly at higher temperatures and lower strain rates, the gamma' phase dissolved resulting in substantial grain growth.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Chemistry, Physical

Flow behavior and dynamic recrystallization of a power metallurgy nickel-based superalloy during hot compression in (γ plus γ′)-phase region

Bing Sun et al.

Summary: The flow behavior and dynamic recrystallization of a powder metallurgy EP962NP nickel-based superalloy in the (gamma + gamma')-phase region have been investigated, showing typical characteristics of dynamic recrystallization behavior and discontinuous dynamic recrystallization mechanism with prevalent observation of necklace structures. The refined recrystallized gamma grains can be obtained with a higher strain rate, and primary gamma' morphology transforms from micron-scale irregular blocks to nano-scale spherical precipitates via dissolution and re-precipitation process during hot compression.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Hot compression behaviors and deformation mechanisms of a Ni-Co-based superalloy with columnar grains

Zijian Zhou et al.

Summary: This study investigated the deformation mechanisms and hot compression behaviors of a Ni-Co-based superalloy prepared using directional solidification. The effects of temperature and strain rate on dynamic recrystallization were analyzed, and constitutive equations were established. The dominant deformation mechanisms were found to be dependent on the strain rate and temperature.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Deformation mechanisms of a γ′ phase strengthened CoNi-based superalloy at high temperatures

Chunhe Chu et al.

Summary: The CoNi-based gamma' phase strengthened superalloy was designed with the addition of alloy elements Al, W, Cr, Ti, and Ta. The size and volume fraction of the gamma' phase can be controlled by post-heat-treatment, which in turn affects the mechanical behavior of the alloy. At different temperatures, the deformation mechanism and correlated mechanical behavior of the alloy undergo significant changes.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Chemistry, Physical

Evolution of Annealing Twins in a Hot Deformed Nickel-Based Superalloy

Yu-Chi Xia et al.

Summary: The hot deformation characteristics of GH4169 superalloy were investigated, and the effects of deformation parameters on flow curves and annealing twins were discussed. It was found that the deformation temperature greatly affected the shapes of flow curves, and the evolution of annealing twins was sensitive to deformation degree, temperature, and strain rate.

MATERIALS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Recrystallization nucleation under close-set 8 phase in a nickel-based superalloy during annealing

Guanqiang Wang et al.

Summary: This research aims to clarify the connections between recrystallization and the delta (8) phase (Ni3Nb) during annealing in Ni-based alloys. The results show that the microstructure and component of the 8 phase dominate the recrystallization nucleation in the alloy.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

Add to Collection

Article Chemistry, Physical

Microstructural origin and control mechanism of the mixed grain structure in Ni-based superalloys

Baoyun Zhang et al.

Summary: This study deeply explores the microstructural origin and control mechanism of mixed grain structure and determines the optimum processing parameters through thermo-mechanical processing. The evolution of microstructure corresponding to the identified optimal parameters is systematically investigated. The study reveals that discontinuous dynamic recrystallization and continuous dynamic recrystallization mechanisms occur simultaneously, and the grain boundary bulging discontinuous dynamic recrystallization dominates the microstructure control.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Review Materials Science, Multidisciplinary

Precipitate coarsening and its effects on the hot deformation behavior of the recently developed γ′-strengthened superalloys

Yuting Wu et al.

Summary: The coarsening behavior of gamma prime precipitates plays a significant role in the properties and hot deformation behavior of gamma'-strengthened superalloys. The particle size is crucial in the morphological evolution of precipitates, with different morphologies observed in different types of superalloys. The coarsening kinetics of precipitates are described using Lifshitz-Slyozof-Wagner (LSW) theory and Trans-Interface Diffusion Controlled (TIDC) theory in the research.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

The kinetics of dynamic recrystallization and construction of constitutive modeling of RAFM steel in the hot deformation process

Guowang Liu et al.

Summary: The study investigates the DRX behavior of austenite in reduced activation ferritic/martensitic steel through isothermal compression tests and constitutive modelling. Flow stress and softening behavior are found to be influenced by deformation temperature and strain rate. A new recrystallization kinetics model is developed to understand the relationship between recrystallization volume fraction and grain size during hot deformation, providing insights for controlling grain size in industrial processes.

JOURNAL OF NUCLEAR MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Dynamic Softening Mechanism and an Improved Unified Constitutive Model for an Al-Cu-Mn-Fe-Zr Alloy during Warm Deformation

Jun-Quan Wang et al.

Summary: The deformation behavior of an Al-Cu-Mn-Fe-Zr alloy is influenced by temperature and strain rate, with the dominant mechanism being dynamic recovery to balance work hardening. Low strain rates consume more dislocations, making it difficult to trigger dynamic recrystallization, while high strain rates promote the process of dynamic recrystallization.

ADVANCED ENGINEERING MATERIALS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

A unified dislocation density-based model for an aged polycrystalline Ni-based superalloy considering the coupled effects of complicate deformation mechanisms and initial δ phase

Zi-Jian Chen et al.

Summary: The research focuses on the flow characteristics and microstructure evolution of an aged nickel-based superalloy through thermal compression experiments at different temperatures and strain rates. A unified model is developed to accurately predict the flow stresses of the alloy, taking into account the morphological changes of the delta phase and the acceleration of dynamic recrystallization behaviors with increased aging time.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Chemistry, Physical

Microstructure Evolution and a Unified Constitutive Model of Ti-55511 Alloy Compressed at Stepped Strain Rates

Gang Su et al.

Summary: The study investigated the flow behavior and microstructure change of the Ti-55511 alloy through thermal compression experiments. A unified constitutive model was developed, considering work hardening effect and dynamic softening mechanisms, with material parameters optimized using a multi-objective algorithm, demonstrating the model's ability to accurately describe the hot compressed alloy's flow features and microstructure evolution.

MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of Stress-Aging Pretreatment on Hot Deformation Behavior and Microstructure Evolution of a Ni-Cr-Nb-Mo-Ti Alloy

Hao Cheng et al.

Summary: The study investigated the hot deformation behavior and microstructure evolution of stress and stress-free aged Ni-Cr-Nb-Mo-Ti alloy through hot compressive tests. It was found that the basket-weave delta-phases refine grains during hot deformation, but significantly hinder the growth of DRX grains and lead to a substantial increase in peak stress. Dislocations pinned near the basket-weave delta-phases can hinder grain boundary migration and accelerate the DRX process during hot deformation.

ADVANCED ENGINEERING MATERIALS (2021)

Add to Collection

Article Chemistry, Physical

Effect of Zener-Hollomon parameter on microstructure evolution of a HEXed PM nickel-based superalloy

Gang Tan et al.

Summary: The microstructure evolution of a hot extrusion powder metallurgy nickel-based superalloy was investigated by hot compression tests, showing that the Z parameter has an impact on the nucleation mechanisms of dynamic recrystallization.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Methods and mechanisms for uniformly refining deformed mixed and coarse grains inside a solution-treated Ni-based superalloy by two-stage heat treatment

Guan-Qiang Wang et al.

Summary: The study investigated the uniform refinement mechanisms in a Ni-based superalloy during two-stage annealing treatment. By selecting suitable times for aging annealing treatment and recrystallization annealing treatment, a mixed microstructure with abnormal coarse recrystallization grains and fine grains can be achieved.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

Add to Collection

Letter Chemistry, Physical

An innovative approach for grain refinement in Ni-based superalloys: Modification in the classical delta process through γ pre-aging treatment

Jian Yang Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Chemistry, Physical

Investigation on the meta-dynamic recrystallization behavior of Inconel 718 superalloy in the presence of δ phase through a modified cellular automaton model

Fuxiang Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Chemistry, Physical

Hot deformation behaviors and three-dimensional processing map of a nickel-based superalloy with initial dendrite microstructure

J. Y. Shen et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Chemistry, Physical

Study on the dynamic recrystallization mechanisms of Inconel 740 superalloy during hot deformation

M. J. Wang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Thermal deformation and dynamic recrystallization of a novel HEXed P/M nickel-based superalloy

Hui-zhong Li et al.

MATERIALS CHARACTERIZATION (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Experimental study and numerical simulation of dynamic recrystallization for a FGH96 superalloy during isothermal compression

Hong Wu et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Nanoscience & Nanotechnology

A dislocation density-based model and processing maps of Ti-55511 alloy with bimodal microstructures during hot compression in α plus β region

Yi-Wei Xiao et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Engineering, Mechanical

Effect of inclusions on low cycle fatigue lifetime in a powder metallurgy nickel-based superalloy FGH96

Dianyin Hu et al.

INTERNATIONAL JOURNAL OF FATIGUE (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Influences of pre-precipitated 8 phase on microstructures and hot compressive deformation features of a nickel-based superalloy

Dao-Guang He et al.

VACUUM (2019)

Add to Collection

Article Chemistry, Physical

Mechanisms of DRX nucleation with grain boundary bulging and subgrain rotation during the hot working of nickel-based superalloys with columnar grains

Bingchao Xie et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Dynamic recrystallization behavior of GH4169G alloy during hot compressive deformation

Dan Jia et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

Add to Collection

Article Chemistry, Physical

Microstructure evolutions of a powder metallurgy superalloy during high-strain-rate deformation

Liming Tan et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Determination of dynamic recrystallization parameter domains of Ni80A superalloy by enhanced processing maps

Guo-zheng Quan et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2019)

Add to Collection

Review Chemistry, Physical

Characterization of the workability of Ni-Fe-Mo alloy by complex processing maps

Aneta Lukaszek-Solek et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Hot deformation behavior and flow stress modeling of a Ni-based superalloy

Martin Detrois et al.

MATERIALS CHARACTERIZATION (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Modeling of thermal deformation behavior near γ′ solvus in a Ni-based powder metallurgy superalloy

Ming Zhang et al.

COMPUTATIONAL MATERIALS SCIENCE (2019)

Add to Collection

Article Chemistry, Physical

Hot deformation behaviors and optimization of processing parameters for Alloy 602 CA

Xiaoyu Qin et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Dynamic recrystallization in Mone1400 Ni-Cu alloy: Mechanism and role of twinning

G. R. Ebrahimi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Hot Deformation Behavior and Processing Maps of a Medium Manganese TRIP Steel

Ning Yan et al.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2019)

Add to Collection

Article Chemistry, Physical

Hot deformation characteristics and dislocation substructure evolution of a nickel-base alloy considering effects of delta phase

Dong-Xu Wen et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Evolution of twins and sub-boundaries at the early stage of dynamic recrystallization in a Ni-30%Fe austenitic model alloy

Wenxiong Chen et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of the Starting Microstructure on the Hot Deformation Behavior of a Low Stacking Fault Energy Ni-based Superalloy

Joshua McCarley et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Modelling the yield point phenomena during deformation at elevated temperatures: case study on Inconel 600

Amir Momeni et al.

PHILOSOPHICAL MAGAZINE (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure evolution and dynamic softening mechanisms during high-temperature deformation of a precipitate hardening Ni-based superalloy

Zhipeng Wan et al.

VACUUM (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Solidification behavior and Laves phase dissolution during homogenization heat treatment of Inconel 718 superalloy

Mohammad Javad Sohrabi et al.

VACUUM (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Hot-workability of super-304H exhibiting continuous to discontinuous dynamic recrystallization transition

K. Arun Babu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Evolution of microstructure and microtexture during hot deformation in an advanced P/M nickel base superalloy

S. S. Satheesh Kumar et al.

MATERIALS CHARACTERIZATION (2018)

Add to Collection

Article Chemistry, Physical

Grain Refinement of a Powder Nickel-Base Superalloy Using Hot Deformation and Slow-Cooling

Xianqiang Fan et al.

MATERIALS (2018)

Add to Collection

Article Automation & Control Systems

Direct powder forging of PM nickel-based superalloy: densification and recrystallisation

Shuyun Wang et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)

Add to Collection

Article Chemistry, Physical

Work hardening characteristics and microstructural evolution during hot deformation of a nickel superalloy at moderate strain rates

S. S. Satheesh Kumar et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Influence of processing parameters on dynamic recrystallization and the associated annealing twin boundary evolution in a nickel base superalloy

S. K. Pradhan et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of cobalt addition on microstructure and hot workability of IN713C superalloy

Yunping Li et al.

MATERIALS & DESIGN (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Characterization of hot deformation behavior of alloy 617 through kinetic analysis, dynamic material modeling and microstructural studies

K. Arun Babu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Materials Science, Multidisciplinary

EBSD analysis of evolution of dynamic recrystallization grains and δ phase in a nickel-based superalloy during hot compressive deformation

Y. C. Lin et al.

MATERIALS & DESIGN (2016)

Add to Collection

Article Chemistry, Physical

Dynamic recrystallization behavior of a γ′-hardened nickel-based superalloy during hot deformation

Hongbin Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

Add to Collection

Article Chemistry, Physical

EBSD study of a hot deformed nickel-based superalloy

Y. C. Lin et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Constitutive modeling for predicting peak stress characteristics during hot deformation of hot isostatically processed nickel-base superalloy

S. S. Satheesh Kumar et al.

JOURNAL OF MATERIALS SCIENCE (2015)

Add to Collection

Article Nanoscience & Nanotechnology

Study of dynamic recrystallization in a Ni-based superalloy by experiments and cellular automaton model

Yan-Xing Liu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of microstructure and γ′ distribution on the hot deformation behavior for a powder metallurgy superalloy FGH96

Chi Zhang et al.

JOURNAL OF MATERIALS RESEARCH (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Dynamic recrystallization behavior of a typical nickel-based superalloy during hot deformation

Xiao-Min Chen et al.

MATERIALS & DESIGN (2014)

Add to Collection

Article Materials Science, Multidisciplinary

The evolution of delta-phase in a superplastic Inconel 718 alloy

Yi Huang et al.

JOURNAL OF MATERIALS SCIENCE (2007)

Add to Collection

Article Materials Science, Multidisciplinary

The effects of elastic stress on microstructural development:: the three-dimensional microstructure of a γ-γ′ alloy

AC Lund et al.

ACTA MATERIALIA (2002)

Add to Collection

© Peeref 2019-2024. All rights reserved.