Related references
Note: Only part of the references are listed.Preliminary Study on Machining of Additively Manufactured Ti-6Al-4V
Jay K. Raval et al.
JOM (2022)
Effect of heat treatment on the microstructure and mechanical property of W/316L multi-material fabricated by selective laser melting
Yan Zhou et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2022)
Analysis of prolonged marine exposure on properties of AH36 steel
Goran Vukelic et al.
ENGINEERING FAILURE ANALYSIS (2022)
Heat treatment effect on the microstructure, mechanical properties, and wear behaviors of stainless steel 316L prepared via selective laser melting
Won-Sang Shin et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)
Improvement of corrosion resistance of SS316L manufactured by selective laser melting through subcritical annealing
Chengshuang Zhou et al.
CORROSION SCIENCE (2020)
The potential of SLM technology for processing magnesium alloys in aerospace industry
T. Kurzynowski et al.
ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2020)
Waviness of Freeform Surface Characterizations from Austenitic Stainless Steel (316L) Manufactured by 3D Printing-Selective Laser Melting (SLM) Technology
Tomasz Kozior et al.
MATERIALS (2020)
Analysis of Welded Joint Properties on an AISI316L Stainless Steel Tube Manufactured by SLM Technology
Petr Mohyla et al.
MATERIALS (2020)
VHCF response of Gaussian SLM AlSi10Mg specimens: Effect of a stress relief heat treatment
A. Tridello et al.
INTERNATIONAL JOURNAL OF FATIGUE (2019)
Additive manufacturing of continuous fibre reinforced thermoplastic composites using fused deposition modelling: Effect of process parameters on mechanical properties
J. M. Chacon et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2019)
Effect of post heat treatment on microstructure and mechanical properties of Ni-based composites by selective laser melting
Hongmei Zhang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Influence of processing parameters on internal porosity and types of defects formed in Ti6A14V lattice structure fabricated by selective laser melting
H. Salem et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Enhancing austenite stability in a new medium-Mn steel by combining deep cryogenic treatment and intercritical annealing: An experimental and theoretical study
Ning Yan et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Properties of oriented carbon fiber/polyamide 12 composite parts fabricated by fused deposition modeling
Guangxin Liao et al.
MATERIALS & DESIGN (2018)
Microstructure, Solidification Texture, and Thermal Stability of 316 L Stainless Steel Manufactured by Laser Powder Bed Fusion
Pavel Krakhmalev et al.
METALS (2018)
Main defects observed in aluminum alloy parts produced by SLM: From causes to consequences
Cassiopee Galy et al.
ADDITIVE MANUFACTURING (2018)
Effect of selective laser melting (SLM) process parameters on microstructure and mechanical properties of 316L austenitic stainless steel
E. Liverani et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Twinning induced plasticity in austenitic stainless steel 316L made by additive manufacturing
M. S. Pham et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Fabrication of continuous carbon, glass and Kevlar fibre reinforced polymer composites using additive manufacturing
Andrew N. Dickson et al.
ADDITIVE MANUFACTURING (2017)
3D printing of polymer matrix composites: A review and prospective
Xin Wang et al.
COMPOSITES PART B-ENGINEERING (2017)
Peep cryogenic treatment of tool steels
B. Podgornik et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)
Effects of process time interval and heat treatment on the mechanical and microstructural properties of direct laser deposited 316L stainless steel
Aref Yadollahi et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
Refinement of Retained Austenite in Super-bainitic Steel by a Deep Cryogenic Treatment
Feng Hu et al.
ISIJ INTERNATIONAL (2014)
Effects of heat treatment influencing factors on microstructure and mechanical properties of a low-carbon martensitic stainless bearing steel
Shaohong Li et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Internal friction measurements of phase transformations during the process of deep cryogenic treatment of a tool steel
Shaohong Li et al.
CRYOGENICS (2013)
Influence of deep cryogenic treatment on microstructure and evaluation by internal friction of a tool steel
Shaohong Li et al.
CRYOGENICS (2010)
Evaluation of factors influencing deep cryogenic treatment that affect the properties of tool steels
A. Oppenkowski et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2010)
Cryogenic Treatment of Tool Materials: A Review
Nirmal S. Kalsi et al.
MATERIALS AND MANUFACTURING PROCESSES (2010)
Effects of deep cryogenic treatment on property of 3Cr13Mo1V1.5 high chromium cast iron
Hao-huai Liu et al.
MATERIALS & DESIGN (2007)
Effect of deep cryogenic treatment on electrode life and microstructure for spot welding hot dip galvanized steel
ZS Wu et al.
MATERIALS & DESIGN (2003)
Effect of deep cryogenic treatment on the mechanical properties of tool steels
A Molinari et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)
Cryogenic treatment to augment wear resistance of tool and die steels
DM Lal et al.
CRYOGENICS (2001)
Share Paper
